Extron electronics TLP Pro 1225MG Manuel utilisateur

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

www.extron.com

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Overview

The Extron®TLP Pro 1225MG, TLP Pro 1525MG, and TLP Pro 1725MG are wall-mounted touchpanels with capacitive, edge-to-edge

glass touchscreens. The TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525MG has a 15.6 inch

screen with a 1366x768 resolution. The TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution. All three touchpanels

are ideal for any AV applications requiring large touchpanels with exible mounting options and fully customizable interfaces. This

guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the

TLPPro 1225, 1525, and 1725 Series User Guide at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

GUI Designer — Used to design layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Global Configurator®Plus and Professional — Used to set up and congure the control processor and touchpanel.

Global Scripter®— Used to rovide an integrated development environment for Extron control systems programming.

Global Scripter provides an Extron-exclusive Python™library (ControlScript®) and modules to get you started.

Toolbelt — Used for device discovery, device information, rmware updates, and conguration of network settings, system

utilities, and user management for TouchLink Pro devices.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you also require:

IP address Subnet mask Gateway

Username — This can be either admin or user.

Passwords — The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords can be changed during conguration. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for

either admin or user).

Make a note of the touchpanel MAC address from the label on the back of the device.

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels until you have read the Attention in the “Power Supply” section of the

TLPPro 1225, 1525, and 1725 Series User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «sources d’alimentation» du TLPPro

1225, 1525, and 1725 Series User Guide.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2).

Connect cables to the touchpanels (see Rear Panel Features on page 4).

Connect the touchpanel to a Power over Ethernet (PoE) injector. The TLP Pro 1725MG ships with the PI 140 power injector.

A power injector must be purchased separately for the 12-inch and 15-inch models.

Connect an Extron IP Link®Pro control processor to the same Ethernet subnetwork as the touchpanel.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 6) or Toolbelt (see Toolbelt Help File) to set the DHCP status and, if necessary, the IP

address, subnet mask, gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).

Associate functions with the graphical user interface features by conguring (see the Global Conﬁgurator Help File) or

programming (see the Global Scripter Help File) the system.

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Mounting

ATTENTION:

• Do not install the TLP Pro 1225MG, TLP Pro 1525MG, or TLP Pro 1725MG in a re resistant rated wall or partition

assembly.

• Ne pas installer le TLP Pro 1225MG, le TLP Pro 1525MG, ou le TLP Pro 1725MG dans un mur résistant au feu ou une

cloison.

• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and

national building codes and electrical codes.

• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du

bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

Wall Mounting

The touchpanels can be wall mounted using the provided hardware. Where local codes require a rear metal enclosure, either model

can be mounted using the Extron BB 700M (not provided). Figure 1 shows the TLP Pro 1525MG. Mount the TLP Pro 1225MG or

TLP Pro 1725MG in the same way.

With a wall box

Some local building codes require the touchpanel to be mounted in a wall box such as the Extron BB 700M. This installation

procedure is described below.

1. Cut a hole in the drywall, 9.6 inches (243 mm) wide

x 6.6 inches (166 mm) high, and install the

Install the BB 700M (optional).

TLP Pro 1525MG

Back View

Hold the touchpanel at a slight angle.

Mount the touchpanel over the two

hooks on the mounting plate.

Add the mounting plate. Align with

the wall box and mark holes for screws.

Secure the mounting plate

to the wall with screws (4).

Place the provided mounting screws (2)

with washers in the mounting screw slot

in the touchpanel.

Secure the touchpanel by tightening the

mounting screws against the base of the

mounting plate.

BB 700M (see gure 1, 1), as described

in the BB 700M Installation Guide (see

www.extron.com).

2. Place the metal mounting plate

against the wall, mark the four

mounting holes, and drill four pilot

holes (2) in those locations.

3. Secure the mounting plate with four

#10 screws (3).

4. Run and connect cables to the back

of the touchpanel (4, and see Rear

Panel Features on page 4).

5. Insert the two provided Phillips pan

head #6-32 x ¾ inch length screws

with washers in the mounting screw

slot (5, see gure 1, Back View

inset). Leave a gap for the ange at the

bottom of the mounting plate to t into.

6. Hold the touchpanel at a slight angle

and lower the notches at the top of

the back panel over the hooks of the

mounting plate (6).

7. Swing the bottom of the touchpanel

inwards so that it lies at against the

mounting plate with the ange at the bottom

of the mounting plate sitting in a groove in the

bottom of the touchpanel.

8. Secure the touchpanel to the mounting plate with the

mounting screws (7).

Without a wall box

If the wall box is not required by local building codes, you can

mount the touchpanel directly into drywall.

1. Download the cut-out template for your touchpanel from

steps 3 through 8

Figure 1. TLP Pro 1525MG Mounting

www.extron.com. Print it at 100% (no scaling).

2. Use the template to mark the wall, cut the hole, and drill the four pilot holes. The size of the cut-out hole is 9.25 inches (235 mm)

wide x 6.25 inches (159 mm) high.

3. Secure the mounting plate and complete the installation, as described in steps 3 through 8 above.

Product Category

Rack Mounting

These touchpanels can be mounted in any standard 19-inch equipment rack, using the optional rack mounting kit. The

TLP Pro 1225MG can be mounted with the RM2 mounting kit. The TLP Pro 1525MG and the TLP Pro 1725MG can be mounted in

the RM3 mounting kit. Read the “Underwriters Labs Guidelines for Rack Mounting” section of the TLPPro 1225, 1525, and 1725

Series User Guide and follow the instructions provided with the appropriate kit.

Front Panel Features

Figure 2 shows the TLP Pro 1225MG front panel. The TLP Pro 1525MG and TLP Pro 1725MG features are very similar.

Figure 2. TLP Pro 1225MG Front Panel

AAmbient light sensor — Monitors ambient light level and adjusts screen brightness.

BStatus light — Can be programmed to provide system feedback. This LED light bar is located above the screen.

CCapacitive touch screen — Provides simple control of AV systems.

zThe TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution.

zThe TLP Pro 1525MG has a 15.6 inch screen with a 1366x768 resolution.

zThe TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution.

DSpeakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the

screen, one on each side of the panel.

EMotion sensor — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.

zIf the sleep timer feature has been set, and no motion has been detected for a user-dened period of time, the touchpanel

enters sleep mode.

zIf the wake on motion feature has been set, and motion is detected by the sensor while the screen is in sleep mode, the

screen display is restored and active.

For more information about setting the Sleep Timer or Wake on Motion, see the “Setup Menu” section of the TLPPro 1225,

1525, and 1725 Series User Guide.

FMenu button — Activates the setup menu (see Setup Menu). Access the button from under the touchpanel. It performs the

same function as the rear panel Menu button but is easier to reach when the touchpanel is installed.

gure 2

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Rear Panel Features

Figure 2 shows the TLP Pro 1225MG rear panel. The TLP Pro 1525MG and TLP Pro 1725MG features are very similar.

RESET

HDMI IN

XTP /

LAN /

PoE

Figure 3. TLP Pro 1225MG Rear Panel

AMounting plate notch (2) — Fit over the hooks at the top of the mounting plate (see Wall Mounting on page 2).

BRESET LED — Provides feedback about the reset status when the user presses the reset button.

CRESET button — Pressing the RESET button allows the unit to be reset in any of three different modes (see Reset Modes:

a Brief Summary on page 5). For more information, see the TLPPro 1225, TLPPro 1525, and TLP Pro 1725 Series User

Guide.

DMENU button — Activates the setup menu (see Setup Menu).

EUSB connectors (2) — For peripheral controls.

FMounting screw slot (2) — Insert the provided screws here to secure the touchpanel to the mounting plate.

GAudio output — One 3.5 mm line level audio output for use with headphones or assistive listening devices.

HHDMI input — For alternative video input.

IXTP/LAN/PoE input

zXTP input — Connect the touchpanel to an Extron XTP®source using a twisted pair cable, terminated with an RJ-45

connector. For complete information about which cables to use, see the user guide for your XTP product.

zLAN input — Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector.

zPoE input — the connector can be used with a PoE power injector (see Connecting Power on page 5).

NOTE: Some XTP models are able to remotely power these touchpanels but not all have that capability. Go to the Extron

website and check the product page for your XTP model to ensure it can power your touchpanel.

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

gure 3

note

Product Category

1. Connect a straight-through Ethernet cable from the power injector to a switch or

router (see gure 4, 1). This cable carries network information from the switch

or router to the power supply input.

2. Connect a second straight-through cable (2) from the power injector to the

TLP Pro touchpanel XTP/LAN/PoE connector (see ﬁgure 3, I, on page 4).

This cable carries the network information and 48VDC from the power injector

to the touchpanel.

3. Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz

power source (gure 4, 3).

Alternatively, use an Ethernet cable to connect the XTP/LAN/PoE port of the interface

to a PoE+ switch or connect the touchpanel directly to an XTP model that is capable

of remotely powering a touchpanel (see the note on page 4).

100-240V~50/60 Hz

1.1A MAX INPUT OUTPUT

POWERED TLP

LAN

To Network or

XTP Device

To a TLP Pro

touchpanel

Extron PI 140

Figure 4. Connecting the Power Injector

Reset Modes: a Brief Summary

These touchpanels offer the following reset modes. For full information about the modes, see the TLPPro 1225, 1525, and 1725

Series User Guide.

• Use factory firmware: Use this mode to replace rmware in the event of rmware failure. Press and hold the RESET

button (see ﬁgure 3, C) while applying power to the unit.

• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les. Press and

hold the RESET button for 6 seconds. After the RESET LED (B) blinks twice, release and

momentarily press the RESET button.

• Reset to Factory Defaults: Use this mode to return the interface to factory default settings. Press and hold the RESET

button for 9 seconds. After the RESET LED blinks three times, release and momentarily press

the RESET button.

NOTES:

• The factory congured passwords for all accounts on this device have been set to the

device serial number. Passwords can be changed during conguration. Passwords are

case sensitive.

• If the device is reset to default settings, the passwords are reset to the default

password, which is extron (for either admin or user).

• Enable or Disable the

DHCP Client:

Use this mode to toggle between DHCP enabled and DHCP disabled.

Press the RESET button ve times, consecutively. After the fth press, do not press the button

again within 3 seconds. If DHCP was enabled, it is now disabled and the RESET LED blinks

three times. If DHCP was disabled, it is now enabled and the RESET LED blinks six times.

NOTES:

• By default DHCP is off and the unit uses a static IP address.

• When you disable the DHCP client, the unit reverts to using the previously-set static IP

address.

Connecting Power

ATTENTION:

• Do not power on the touchpanels until you have read the Attention in the “Rear Panel Features” section of the TLPPro

1225, 1525, and 1725 Series User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du

TLPPro 1225, 1525, and 1725 Series User Guide.

The TLP Pro 1725MG ships with the Extron PI 140 power injector included. For the TLP Pro 1225MG and TLP Pro 1525MG, the

power injector must be purchased separately. Figure 4 shows the PI 140. Your power injector may look different.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

For information about replacing and disposing of batteries, see the TLPPro 1225, 1525, and 1725 Series User Guide at

www.extron.com.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Setup Menu

Press the MENU button (ﬁgure 2, Fon page 3 or ﬁgure 3, D,

on page 4) to open the setup menu. Select any of the six available

screens (Status, Network, Display, Audio, Input and Advanced)

by tapping the appropriate button in the navigation bar at the top of

the screen (for more information, see the TLPPro 1225, 1525, and

1725 Series User Guide).

Figure 5 shows the setup menu for the TLP Pro 1225MG. The setup

menu for the TLP Pro 1525MG and TLP Pro 1725MG are very similar.

Info

Model: TLP Pro 1225MG

Part Number: 60-1787-02

Firmware

Version:1.02.0001-b001

PoE Status: Active

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

GUI Project:

Sleep Timer:

1280x800

5 Minutes

Audio

System Volume:

System Mute: Off

100

Input

HDMI Port: No Signal

Status Display AudioAdvanced Exit

NetworkInput

Advanced

Controller IP: 192.168.254.250

Project Size: 1/196 MB

Bootloader

Version:1.03.0000

XTP: 1280x720 HDCP

Figure 5.Setup Menu: Status page for TLP Pro 1225MG

68-3474-50 Rev. C

10 21

Autres manuels pour TLP Pro 1225MG

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Écran tactile

Extron electronics

Extron electronics TLP Pro 1220MG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1725TG Manuel utilisateur

Extron electronics

Extron electronics RWM 1 Manuel utilisateur

Extron electronics

Extron electronics TLP 700MV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1220MG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1020T Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1520TG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1225TG Manuel utilisateur

Extron electronics

Extron electronics ZRTP Series Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1230WTG Manuel utilisateur

Extron electronics

Extron electronics BB 1000M Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 525T Series Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP Pro 1020 Series Manuel utilisateur

Extron electronics

Extron electronics TLP 710MV Manuel utilisateur

Extron electronics

Extron electronics Scan Rate Indicator SRI 200 Manuel utilisateur

Extron electronics

Extron electronics SMK 2 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 720M Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP 710TV Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP Pro 520M Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP 350CV Manuel utilisateur

Extron electronics

Extron electronics TLP 1000MV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1225MG Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP Pro 1025T Series Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 720C Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur