Extron electronics TLP Pro 1230WTG Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLP Pro 1230WTG • Setup Guide

Overview

The Extron®TLP Pro 1230WTG is a 12"ultra-wide tabletop touchpanel with a capacitive, edge-to-edge glass touchscreen

and a resolution of 1920x720. It has a weighted base that allows it to stand on any suitable table or desktop. It is ideal for

any AV applications requiring a large touchpanel with a fully customizable interface. This guide provides instructions for

experienced installers to mount and install the touchpanel. For more complete details, see the TLPPro 1230WTG User Guide at

www.extron.com.

Setup Overview and Checklist

Get Ready

Download and install the latest version of the following software:

zGUI Designer — For designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces

zGlobal Configurator®Plus and Professional — For setting up and conguring the control processor and touchpanel

zGlobal Scripter®— Provides an integrated development environment for Extron control systems programming. Global

Scripter provides an Extron-exclusive Python™library (ControlScript®) and Global Scripter modules to get you started.

zToolbelt — For device discovery, device information, rmware updates, and conguration of network settings, system

utilities, and user management for TouchLink Pro devices.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you also require:

IP address Subnet mask Gateway

Username — This can be either admin or user.

Passwords — The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords can be changed during conguration. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for

either admin or user).

Make a note of the touchpanel MAC address.

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels until you have read the Attention in the “Power Supply” section of the

TLPPro 1230WTG User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «sources d’alimentation» du

TLPPro 1230WTG User Guide.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2).

Connect cables to the touchpanels (see Rear Panel and Base Features on page 3).

Connect the touchpanel to a power source. These models must be powered by PoE. A power injector must be purchased

separately.

An Extron IP Link®control processor must be connected to the same Ethernet subnetwork as the touchpanel.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,

gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

Create a graphical user interface with GUI Designer (see the GUI Designer Help File for step-by-step instructions).

Associate functions with the graphical user interface features using Global Congurator or Global Scripter.

TLP Pro 1230WTG • Setup Guide

Mounting

Go to www.extron.com to see a list of optional mounting kits that are available for this model. The kits must be purchased

separately. Follow the installation instructions provided with the kit.

Desktop Mounting

These touchpanels come assembled with stands that allow them to be placed on any suitable at surface (for example a desk, table,

or lectern).

Fixed Mounting

1. Mark the location for two mounting holes, 4.96inches (126 mm) apart (see ﬁgure 2, B, on page 3).

2. Drill two pilot holes into the desktop.

3. Insert two #10 at-head wood screws (not provided) through the touchpanel and align them with the two pilot holes.

4. Secure the touchpanel to the tabletop.

SMA-1 Swivel Mount Adapter

To permanently mount the touchpanel and swivel it up to 180° in either direction, use the optional Extron SMA-1 swivel mount

adapter.

1. Attach the conduit, insulation disk, and swivel disk and congure the set screws to allow for the degree of swivel that is required

(see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com).

2. Place the mounting hole in the base over the conduit of the SMA-1.

3. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide.

Front Panel Features

A B C

Figure 1. TLP Pro 1230WTG Front Panel

AAmbient light sensor — Monitors ambient light level and adjusts screen brightness.

BMotion sensor — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.

zIf the Sleep Timer has been set, and no motion has been detected for a user-dened period of time, the touchpanel

enters sleep mode.

zIf Wake on Motion has been set, and motion is detected by the sensor while the screen is in sleep mode, the screen

display is restored and active.

For further information about setting the Sleep Timer and Wake on Motion, see the “Setup Menu” section in the

TLP Pro 1230WTG User Guide, which is available at www.extron.com.

CCapacitive touch screen — Provides simple control of AV systems. The TLP Pro 1230WTG has a 12 inch screen with a

1920x720 resolution.

DSpeakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the

screen, one on each side of the panel.

EStatus light — Can be programmed to provide system feedback. The LED light bar is located under the screen.

Product Category

Rear Panel and Base Features

A E

E F

Figure 2. TLP Pro 1225TG Rear Panel and Base

ASpeakers (2) — For video preview and audible feedback for the user.

BMounting Holes — Used to secure the touchpanel to a desktop or other at surface (see Desktop Mounting on page 2).

CCable Guide — The LAN/PoE and HDMI cables are inserted through this hole at the back of the base (see “TLP Pro 1230WTG

Base Features” in the TLP Pro 1230WTG User Guide).

DLAN/PoE Connector — These touchpanels must be powered by Power over Ethernet (PoE; see “Connecting Power” below).

ATTENTION:

• Do not power on the touchpanels until you have read the Attention notice in the “Power Supply” section of the

TLP Pro 1230WTG User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «PowerSupply» du

TLP Pro 1230WTG User Guide.

NOTE: The TLP Pro 1230WTG ships without a power injector. The power injector must be purchased separately.

EUSB connector — Compatible with USB 2.0. The port is concealed behind a plastic cover, which can be removed with a small,

at-bladed screw driver.

FRear status light — An LED light bar that can be programmed to provide system feedback.

GHDMI Connector — A recessed connector for HDMI input.

HMENU button — Activates the Setup Menu (see page 4).

IRESET button — Pressing the RESET button allows the unit to be reset in any of three different modes and can also be used to

toggle between enabling and disabling the DHCP client (see Reset Modes: A Brief Summary on page 4)

JRESET LED — Provides feedback about the reset status when the user presses the RESET button (see Reset Modes: A Brief

Summary).

Connecting Power

ATTENTION:

• Do not power on the touchpanels until you have read the Attention notice in the “Power Supply” section of the

TLP Pro 1230WTG User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «PowerSupply» du

TLP Pro 1230WTG User Guide.

The TLP Pro 1230WTG must be powered by Power over Ethernet (PoE). The power injector must be purchased separately. The

PI 140 is shown in ﬁgure 3 on page 4. Your power injector may look different.

gure 2

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

For information about replacing and disposing of batteries, see the TLP Pro 1230WTG User Guide at www.extron.com.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

68-3147-50 Rev. A

01 21

TLP Pro 1230WTG • Setup Guide

1. Connect a straight-through Ethernet cable from the power injector

to a switch or router. This cable carries network information from

the switch or router to the power supply input.

2. Connect a second straight-through cable from the power injector

to the PoE/LAN connector of the touchpanel (see ﬁgure 2, D,

on page 3). This cable carries the network information and

48VDC from the power injector to the touchpanel.

3. Connect the IEC power cord to a convenient 100 VAC to 240 VAC,

50-60 Hz power source.

Alternatively, use an Ethernet cable to connect the LAN/PoE+ port of

the touchpanel to a PoE+ switch.

100-240V~50/60 Hz

1.1A MAX INPUT OUTPUT

POWERED TLP

LAN

To Network or

XTP Device

To a TLP Pro

touchpanel

Extr

on PI 140

Figure 3. Connecting the Power Injector

Reset Modes: A Brief Summary

The TLP Pro 1230WTG offers the following reset modes. For complete information, see the TLPPro 1230WTG User Guide.

• Use factory firmware: Use this mode to replace rmware in the event of rmware failure. Press and hold the RESET

button (I) while applying power to the unit.

• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les. Press and hold

the RESET button for 6 seconds. After the RESET LED (J) blinks twice (at 3 and 6 seconds),

release and momentarily press the RESET button.

• Reset to Factory Defaults: Use this mode to return the touchpanel to factory default settings, including passwords. Press

and hold the RESET button for 9 seconds. After the RESET LED blinks three times (at 3, 6 and 9

seconds), release and momentarily press the RESET button.

NOTES:

• The factory congured passwords for all accounts on this device have been set

to the device serial number. Passwords can be changed during conguration.

Passwords are case sensitive.

• If the device is reset to default settings, the passwords are reset to the default

password, which is extron (for either admin or user).

• Enable or Disable the

DHCP Client:

Use this mode to toggle between DHCP enabled and DHCP disabled. Press the RESET button

ve times, consecutively. After the fth press, do not press the button again within 3 seconds.

If DHCP was enabled, it is now disabled and the RESET LED blinks three times. If DHCP was

disabled, it is now enabled and the RESET LED blinks six times.

NOTES:

• By default DHCP is off and the unit uses a static IP address.

• When you disable the DHCP client, the unit reverts to using the previously-set static IP

address.

Setup Menu

Press the Menu button (H) to open the setup menu. Select

any of the six available screens (Status, Network, Display,

Audio, Input and Advanced) by tapping the appropriate

button in the navigation bar at the top of the screen (for more

information, see the TLPPro 1230WTG User Guide).

Info

Model: TLP Pro 1225MG

Part Number: 60-1787-02

Firmware

Version:1.02.0001-b001

PoE Status: Active

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

GUI Project:

Sleep Timer:

1280x800

5 Minutes

Audio

Master Volume:

Master Mute:Off

100

Input

HDMI Port: No Signal

Status Display AudioAdvanced Exit

NetworkInput

Advanced

Controller IP: 192.168.254.250

Project Size: 1/196 MB

Bootloader

Version:1.03.0000

Figure 4. Setup Menu: Status Page for TLP Pro 1230WTG

gure 3

Autres manuels pour TLP Pro 1230WTG

Table des matières

Autres manuels Extron electronics Écran tactile

Extron electronics

Extron electronics TouchLink TLP 710TV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 720M Manuel utilisateur

Extron electronics

Extron electronics RWM 1 Manuel utilisateur

Extron electronics

Extron electronics TLP 1000MV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1020T Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 300M Series Manuel utilisateur

Extron electronics

Extron electronics TLP 710MV Manuel utilisateur

Extron electronics

Extron electronics TouchLink TLP Pro 1025T Series Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1230WTG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1520TG Manuel utilisateur

Extron electronics

Extron electronics TLP 1000MV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 720M Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 720C Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 525M seriesl Manuel utilisateur

Extron electronics

Extron electronics TLP 700TV Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1225MG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1225MG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1220TG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 725T Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 525T Series Manuel utilisateur

Extron electronics

Extron electronics SMK 2 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1220MG Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 1220MG Manuel utilisateur

Extron electronics

Extron electronics TLP 700MV Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur