Extron electronics CVC 300 Manuel utilisateur

Installation Guide

Component Video and HDTV to RGB Converter

68-1541-01 Rev. B

12 08

CVC 300

The Extron CVC 300 Component Video Converter converts all

standard component video formats: NTSC/PAL, DVD, and

Betacam®, to RGBHV or RGBS; and converts SMPTE HDTV

component video to RGBHV. The CVC 300 can also strip

sync-on-green (SOG) from RGsB video. The converter outputs

RGBHV or RGBS video on BNC connectors. The ﬁgure below

shows a typical CVC 300 application.

LAN

ACT LINK

RESET

OUTPUTS

INPUTS

Matrix Switcher

Projector

RGBHV

Component

POWER

12V

3A MAX

CVC 300

OUTPUT

RG B V

H/HV

PR/R PB/B

Y/G

INPUT

DSS Receiver

Blu-ray Disc

Extron

CVC 300

Component Video

Converter

The component video input formats include SMPTE, HDTV

and Betacam component video. The RGsB video input can be

computer video or NTSC/PAL video.

Mounting

The 1U high, quarter rack width, CVC 300 converter can be

mounted to a rack, under a desk or tabletop, or on a projector

bracket. It can be rack mounted using one-quarter of a 1U

Universal Rack Shelf, RSU 129 (part #60-190-01) or 1U Basic

Rack Shelf, RSB 129 (part #60-604-01).

UL rack mounting guidelines

The following Underwriters Laboratories (UL) guidelines

pertain to the installation of the CVC 300 into a rack.

Elevated operating ambient temperature — If the1.

equipment is installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the

rack environment may be greater than room ambient

temperature. Therefore, install the converter in an

environment compatible with the maximum ambient

temperature (Tma = +104 °F, +40 °C) speciﬁed by Extron.

Introduction

CVC 300 • Installation

Introduction

Reduced air ﬂow — Install the equipment in a rack so that2.

the amount of air ﬂow required for safe operation of the

equipment is not compromised.

Mechanical loading — Mount the equipment in the rack so3.

that a hazardous condition is not achieved due to uneven

mechanical loading.

Circuit overloading — Connect the equipment to4.

the supply circuit and consider the effect that circuit

overloading might have on overcurrent protection and

supply wiring. Appropriate consideration of equipment

nameplate ratings should be used when addressing this

concern.

Reliable earthing (grounding) — Maintain reliable5.

grounding of rack-mounted equipment. Pay particular

attention to supply connections other than direct

connections to the branch circuit (e.g. use of power strips).

Mounting instructions

Rack mount the CVC 300 as follows:

Remove the feet from the CVC, if they were previously1.

installed.

Mount the CVC 300 on the rack shelf, using two2.

4-40 x 3/16" screws in opposite corners (under the shelf) to

secure the converter to the shelf (see below).

Use 2 mounting holes on

opposite corners.

(2) 4-40 x 3/16"

Screws

1U Universal Rack Shelf

Both front false faceplates

use 2 screws.

QuarterRackStandardShelf

1/4 Rack Width Front False

Faceplate

1/2 Rack Width Front False

Faceplate

Mounting

CVC 300 • Installation 2

Cable Connection and Rate Selection

CVC 300 • Cable Connection

Cable Connection and Rate Selection

See the illustrations below to identify the panel connections.

POWER

12V

1.0 A MAX

CVC 300

OUTPUT

RGB V

H/HV

/R P

Y/G

INPUT

COMPONENT VIDEO CONVERTER

CVC 300

FORMAT

aPower connector — Plug the external 12 VDC power supply

here using the included 2-pole captive screw connector

(See "Power supply wiring").

bInput connectors — Connect a component (SMPTE, HDTV,

or Betacam) or RGsB video input device to these female BNC

connectors. Connect the input device as shown below.

Y, PR, PB

Video

RGsB

(SOG)

Video

Y, B-Y, R-Y

Video

B-YR-Y

PR /R PB /BY/G

PR /RPB /BY/G

cOutput connectors — Connect an RGBHV or RGBS display to

these female BNC connectors. Connect the display as shown

below.

R G BH/HV V

RGBHV

Video

RGBS

Video

R G B H/HV V

dPower LED — Green when power is applied and an active

video input is detected. Amber if power is available but no

input signal is present.

Cable Connection and Rate Selection (Cont’d)

CVC 300 • Rate Selection 4

eInput Format rotary switch — Use an Extron

Tweeker or other small screwdriver to set the Format

rotary switch to match the video input format. The

following table shows switch settings and their

assigned input video formats.

Position Input Resolutions Output

Position 0 Reserved for future use

Position 1

(Default): YUVp/HD 480p, 576p, 720p,

1080i, 1080p RGBHV

Position 2: RGsB 480i/p, 576i/p,

640x480 to 1920x1200 RGBHV

Position 3: YUVi 480i, 576i RGBHV

Position 4: RGsB HD 720p, 1080i, 1080p RGBHV

Position 5: Betacam 50 480i, 576i RGBHV

Position 6: Betacam 60 480i, 576i RGBHV

Position 7: YUVp 480p, 576p RGBS

Position 8 RGsB 480i/p, 576i/p,

640x480 to 1920x1200 RGBS

Position 9: YUVi 480i, 576i RGBS

Position A: RGsB HD 720p, 1080i, 1080p RGBS

Position B: Betacam 50 480i, 576i RGBS

Position C: Betacam 60 480i, 576i RGBS

D, E and F Reserved for future use

Input Format Table (Rotary Switch)

Power Supply Wiring

CVC 300 • Power Supply Wiring

Power supply wiring

NThis product is intended to be powered by a UL Listed

power supply with an output rated at 12 VDC, 2 A.

Wire the supplied male power connector (plug) as shown below.

Captive Screw Connector

SECTION A–A

Power Supply

Output Cord

Ridges

Smooth

Tie Wrap

CPower supply voltage polarity is critical. Incorrect

polarity can damage the power supply and the product.

Identify the power cord negative lead by the ridges on the

side of the cord.

NThe length of the exposed (stripped) copper wires is

important. The ideal length is 3/16” (5 mm). Longer bare

wires can short together. Shorter wires are not as secure in

the captive screw connectors and could be pulled out.

Do not tin the stripped power supply leads. Tinned wires

are not as secure in the captive screw connectors and could

be pulled out.

To verify the polarity before connection, plug in the power

supply with no load and check the output with a voltmeter.

WThe two power cord wires must be kept separate while

the power supply is plugged in. Remove power before

wiring.

As an alternative, an Extron PS 123 Universal 12 VDC Power

Supply, part #60-814-01, can power multiple Extron 12 VDC

devices using only one AC power connector.

Insert the wired plug into the power connector on the rear

panel, then connect AC power.

Speciﬁcations

CVC 300 • Specications 6

Video input

Number/signal type..................... 1 component video [HDTV

(Y, PR, PB), SMPTE (Y, R-Y, B-Y), or

Betacam®(Y, R-Y, B-Y)] or RGsB

Connectors ..................................... 3 BNC female

Nominal level ................................ 1 Vp-p for Y of component video and

for G of RGsB

0.7 Vp-p for PB, PR, R-Y and B-Y of

component video, and for R and B of RGsB

Minimum/maximum levels........ 0 V to 1.5 Vp-p with no offset

Impedance...................................... 75 ohms

Horizontal frequency.................... 15 kHz to 100 kHz according to selected

mode

Vertical frequency.......................... 50 Hz to 120 Hz

Resolution range ........................... 640x480 to 1920x1200, 480i/p, 576i/p,

720p, 1080i/p

Return loss...................................... <-35 dB @ 10 MHz

Video output

Number/signal type..................... 1 RGBHV, RGBS

Connectors ..................................... 5 BNC female

Nominal level ................................ 0.7 Vp-p for RGB

Minimum/maximum levels........ RGB: 0.0 V to 0.7 Vp-p

Impedance...................................... 75 ohms

Return loss...................................... <-45 dB @ 10 MHz

Vertical frequencies....................... Locked to the detected input rate

Sync

Input type....................................... RGsB; YUV; Y, R-Y, B-Y

Output type.................................... RGBHV, RGBS

Standards........................................ SMPTE 170M (NTSC), SMPTE 274M

(1080i/p), SMPTE 293M (480p), SMPTE

296M (720p)

Input level ...................................... 0.3 V to 1.0 Vp-p (sync + video)

Output level ................................... 0.0 V to 5.0 Vp-p

Input impedance ........................... 75 ohms (on Y or Gs connector)

Output impedance ........................ 75 ohms (on H/HV and V connectors)

Speciﬁcations

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.29918 80 FAX

Speciﬁcations (Cont’d)

General

External power supply................. 100 VAC to 240 VAC, 50-60 Hz, external;

to 12 VDC, 2 A, regulated

Power input requirements ........... 12 VDC, 1.0 A

Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /

10% to 90%, noncondensing

Operating: +32 to +104 °F (0 to +40 °C) /

10% to 90%, noncondensing

Cooling ........................................... Convection, no vents

Mounting

Rack mount ........................ Yes, with optional 1U, 9.5" deep rack shelf

(RSU 129, #60-190-01; RSB 129, 60-604-01);

or 1U, 6" deep rack shelf (RSU 126,

#60-190-10; RSB 126, 60-604-10)

Furniture mount................ Yes, with optional MBU 125 Under

Desk Mount kit (70-077-01) or MBU 129

Through Desk Mount kit (70-077-02)

Enclosure type ............................... Metal

Enclosure dimensions................... 1.7" H x 4.3" W x 6.0" D (1U high, quarter

rack wide)

(4.3 cm H x 10.9 cm W x 15.2 cm D)

(Depth excludes connectors.)

Product weight .............................. 0.8 lbs (0.4 kg)

Shipping weight ............................ 2 lbs (1 kg)

Vibration......................................... ISTA 1A in carton (International Safe

Transit Association)

Regulatory compliance

Safety................................... CE, CUL, UL

EMI/EMC .......................... CE, C-tick, FCC Class A, ICES,

VCCI Class A

MTBF............................................... 30,000 hours

Warranty......................................... 3 years parts and labor

NAll nominal levels are at ±10%.

NSpeciﬁcations are subject to change without notice.

Table des matières

Autres manuels Extron electronics Convertisseur de média

Extron electronics

Extron electronics DSC HD-HD Manuel utilisateur

Extron electronics

Extron electronics DVC 501 SD Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics Quantum Ultra Series Manuel utilisateur

Extron electronics

Extron electronics HAE 100 Manuel utilisateur

Extron electronics

Extron electronics CLK 100 Manuel utilisateur

Extron electronics

Extron electronics HAE 100 4K Plus Manuel utilisateur

Extron electronics

Extron electronics BUC 202 Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics NAV 10SD 101 Manuel utilisateur

Extron electronics

Extron electronics NAV E 401 D Manuel utilisateur

Extron electronics

Extron electronics SMD 101 Manuel utilisateur

Extron electronics

Extron electronics mediaport 200 Manuel utilisateur

Extron electronics

Extron electronics Emotia Xtreme Manuel utilisateur

Extron electronics

Extron electronics Scan Converter VSC 500 Manuel utilisateur

Extron electronics

Extron electronics Video and Sync Converter/Stabilizer SC 210 Manuel utilisateur

Extron electronics

Extron electronics TSC 100 Manuel utilisateur

Extron electronics

Extron electronics Inertia Manuel utilisateur

Extron electronics

Extron electronics VSC 50 Manuel utilisateur

Extron electronics

Extron electronics DVC RGB-HD A Manuel utilisateur

Extron electronics

Extron electronics MediaPort 300 Manuel utilisateur

Extron electronics

Extron electronics 60-728-01 Manuel utilisateur

Extron electronics

Extron electronics Emotia Jr. 800 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur