Extron electronics Cable Cubby F55 Edge Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

product specifications.

Cable Cubby F55 Edge • Installation Guide

The Extron Cable Cubby F55 Edge is an edge-mount cable

access enclosure that integrates AV technology and power on

the furniture surface. It is designed for congurable rooms that

require semi-permanent AV connectivity, control, and power.

An integrated clamp system secures the enclosure to the

furniture without requiring tools or cutting.

This guide provides instructions for an experienced installer to

install and connect the Extron Cable Cubby F55 Edge Cable

Access Enclosure.

Kit Contents

Flex55 Adapter Module (2)

Grommet

Plugs (8)

Zip Ties (4)

Pry Tool (2)

Cable Grommet

Plate (2)

Cable Cubby F55 Edge

Figure 1. Cable Cubby F55 Edge Kit Contents

Planning

Read the following information before installing the Cable Cubby F55 Edge.

Check with Local and State Regulations Before Starting the Installation:

• Ensure that the planned installation complies with building and electrical codes.

• Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check All Parts and Equipment Before Installation:

• Ensure that all parts are present in each kit.

• Ensure that necessary tools and equipment are available for the installation.

NOTE: Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact

or entanglement (see Routing and Connecting Cables on page9).

VOLUME

DISPLAY

PC VIDEO

OFF

MUTE

LAPTOP

VOLUME

DISPLAY

PC VIDEO

MUTE

LAPTOP

OFF

USB CHARGER

120V 50-60Hz 6A MAX

ZipClip 100 ZipClip 200 ZipClip 400

PMK 155

Optional Accessories

Cable Cubby F55 Edge • Installation Guide (Continued)

Application Diagram

The application diagram below shows a power, data, and video wiring setup from a laptop to a conference monitor. The setup is

made simple by using the included Cable Cubby Flex55 Captive Cable Kit, installed in the Cable Cubby F55 Edge enclosure.

Q4 Sales by Region

Northwest

Northeast

Southwest

Southeast

Central

Q4 Sales by Region

Northwest

Northeast

Southwest

Southeast

Central

DISPLAY

OFF

VOLUME

PC VIDEO

MUTE

LAPTOP

USB CHARGER 120V 50-60 Hz 6A MAX

Power HDMI

Extron

Cable Cubby F55 Edge

Edge Mount Cable Access

Enclosure for AV Connectivity,

Control, and Power

Figure 2. Application Example Using the Cable Cubby F55 Edge Enclosure

Preparing the Cable Cubby F55 Edge

The Cable Cubby F55 Edge enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations (see

the example in gure3). These modules can be installed either before or after the Cable Cubby F55 Edge installation. Optional

Retractor modules can be installed with the appropriate brackets, sold separately. Detailed retractor installation instructions are

available with the Retractor bracket kit and in the Cable Cubby F55 Edge Retractor Module Setup Guide at www.extron.com.

VOLUME

DISPLAY

PC VIDEO

OFF

MUTE

LAPTOP

VOLUME

DISPLAY

PC VIDEO

MUTE

LAPTOP

OFF

USB CHARGER

120V 50-60Hz 6A MAX

Figure 3. Cable Cubby F55 Edge with Control, Power, and Cable Pass-through Modules

NOTE: For a complete and up-to-date list of compatible modules, see the product page at www.extron.com.

Cable Cubby F55 Edge • Installation Guide (Continued)

Installing Modules into the Cable Cubby F55 Edge

The following illustration shows the process for installing the double-size Flex55 AC+USB 130 US Power Module into the Cable

Cubby F55 Edge enclosure. Note that half- and full-size modules can be snapped into the enclosure without removing the

supports (1). Retractor modules also can be installed, in any slot in the enclosure (see the Cable Cubby F55 Edge Retractor

Setup Guide, available at www.extron.com, for more information).

Extron Cable Cubby

F55 Edge Enclosure

Plan and prepare the enclosure for

module installation.

For a double-size module installation,

use pliers to carefully twist the desired

bridge support back and forth until loose,

and remove.

NOTE: Removal of a bridge

support is irreversible.

Figure 4. Removing a Module Support for Double-sized Flex55 Installation

Snap the grommet plate

into the Adapter Module.

Snap included grommet plugs

into any unused holes in the

grommet plate.

2Install the cable grommet plate for cable pass-through applications.

For cable pass-through installation,

insert the cables through the bottom

of the Cable Cubby F55 Adapter Module

and through the holes of the gr

ommet plate.

Figure 5. Installing the Cables

Attach additional

devices here.

Extron Cable Cubby

Flex55 Edge Enclosure

xtron Cable Cubby

lex55 Edge Enclosur

Extron

Flex55 AC+USB 130 US

Insert the module into

the Cable Cubby.

Connect to

power source.

USB CHARGER

120V 50-60Hz 6A MAX

Figure 6. Installing the Flex55 AC+USB 130 US into the Cable Cubby F55 Edge Enclosure

Cable Cubby F55 Edge • Installation Guide (Continued)

Attaching an Optional ZipClip Mounting Device to the Cable Cubby F55 Edge

The ZipClip 100, 200, or 400 can be attached to the Cable Cubby F55 Edge in order to mount a power supply or other device to

the Cable Cubby. Determine which ZipClip to use (depending on the device being attached) and in which orientation (vertical or

horizontal). Note that the ZipClip 400 can be mounted horizontally only. Plan and ensure that there is ample space for the device

and its cables.

21-XYZ-01LF

ZipClip 100 — Vertical Mounting ZipClip 100 — Horizontal Mounting

ZipClip 200 —

Vertical Mounting ZipClip 200 — Horizontal Mounting

ZipClip 400 — Horizontal Mounting

Figure 7. Mounting ZipClips

Attaching an Optional PMK 155 Mounting Kit

Follow these steps to attach a PMK 155 Mounting Kit to the Cable Cubby F55 Edge.

1. The Cable Cubby F55 Edge is delivered with an accessory mounting bracket attached. Detach this bracket by removing its

two mounting screws (see figure8). Set the bracket and screws aside. You will reattach them in step 3.

Accessory Bracket

Figure 8. Removing the Accessory Mounting Bracket from the Cable Cubby F55 Edge

2. Attach the PMK 155 to the accessory bracket using the two screws and washers from the PMK kit (see figure9).

Figure 9. Attaching the PMK 155 to the Accessory Bracket

Cable Cubby F55 Edge • Installation Guide (Continued)

3. Attach the accessory bracket and PMK 155 to the Cable Cubby F55 Edge, using the two screws removed in step 1.

Figure 10. Attaching the PMK 155 and Accessory Bracket to the Cable Cubby F55 Edge

Mounting the Cable Cubby F55 Edge to a Table

Mount the Cable Cubby F55 Edge on the edge of the table as shown below.

Under the table, turn both thumbscrew clamps

and tighten them snugly to secure the enclosure.

Ensure the Cable Cubby F55 Edge is ﬁrmly secured

to the furniture.

Hold the assembled

Cable Cubby F55 Edge

enclosure onto the edge

of the table.

Figure 11. Mounting the Cable Cubby F55 Edge to a Table

Routing and Connecting Cables

Organize and connect cables as shown in gure12. Use zip ties (provided) to fasten the cables to the enclosure where needed.

DISPLAY

OFF

VOLUME

PC VIDEO

MUTE

LAPTOP

USB CHARGER 120V 50-60Hz 6A MAX

Zip tie locations on th

inside of the clamps

Figure 12. Routing and Managing the Cables

Cable Cubby F55 Edge • Installation Guide (Continued)

Appendix — Removing Modules from the Cable Cubby F55 Edge

If the modules need to be replaced or removed from the Cable Cubby F55 Edge enclosure, the following diagrams show the procedure

for removing modules with the provided pry tool. This process applies to any compatible Flex55 and EU module.

NOTE: To verify the location of the locking tabs, check the module specifications (available at www.extron.com).

Unhook the other locking tabs, if applicable,

and remove the module.

HDMI

USB CHARGER

120V 50-60Hz 6A MAX

VOLUME

DISPLAY

PC VIDEO

OFF

MUTE

LAPTOP

VOLUME

DISPLAY

PC VIDEO

MUTE

LAPTOP

OFF

Insert pry tool

at the locking

tab location.

wo pry tools may

need to be used

simultaneously for

lar

ger modules to

unhook.

Locking

Tab

USB CHARGER

120V 50-60Hz 6A MAX

USB CHARGER

Pull the pry tool away from

the module to unhook each

locking tab from the

mounting frame.

Repeat steps 1 and 2 to

unhook the locking tabs

on the other side of the module.

To verify the location of the locking tabs,

check the module specications.

Figure 13. Removing Modules

Autres manuels pour Cable Cubby F55 Edge

Table des matières

Autres manuels Extron electronics Enceinte

Extron electronics

Extron electronics HSA 200SE Manuel utilisateur

Extron electronics

Extron electronics HSA 822M Manuel utilisateur

Extron electronics

Extron electronics HSA 822 Manuel utilisateur

Extron electronics

Extron electronics PowerCage 411 Series Manuel utilisateur

Extron electronics

Extron electronics EBP 1200C Manuel utilisateur

Extron electronics

Extron electronics PVM 220 Manuel utilisateur

Extron electronics

Extron electronics PowerCage 411 Manuel utilisateur

Extron electronics

Extron electronics TLM 100 T Manuel utilisateur

Extron electronics

Extron electronics PowerCage 1600 Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 202 Manuel utilisateur

Extron electronics

Extron electronics EWB 212 Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 300C Manuel utilisateur

Extron electronics

Extron electronics HSA 400 Series Manuel utilisateur

Extron electronics

Extron electronics NBP 1200C Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 500 Manuel utilisateur

Extron electronics

Extron electronics PowerCage 1600 Manuel utilisateur

Extron electronics

Extron electronics PowerCage 1600 Manuel utilisateur

Extron electronics

Extron electronics PowerCage 401 Manuel utilisateur

Extron electronics

Extron electronics EWB 112 Manuel utilisateur

Extron electronics

Extron electronics CCD 220 Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 300S Manuel utilisateur

Extron electronics

Extron electronics PowerCage 401 Manuel utilisateur

Extron electronics

Extron electronics Hideaway HSA 200C Series Manuel utilisateur

Extron electronics

Extron electronics CS 120P Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur