Extech Instruments HD350 Manuel utilisateur
User Manual
Heavy Duty Pitot Tube Anemometer and Differential
Pressure Manometer
Model HD350
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
2 HD350-en-GB_V3.4 2/19
Introduction
Congratulations on your purchase of the Extech HD350. This handheld meter measures and
displays air velocity (speed), air flow (volume), ambient air temperature, and gauge/differential
pressure. This meter is shipped fully tested and calibrated and, with proper use, will provide years
of reliable service.
Features
Pitot tube Anemometer measurements for Air Velocity and Air Flow (volume).
Manometer (Differential Pressure) Measurements.
Simultaneous display of Air Flow or Air Velocity, Temperature, and Pressure.
5 selectable pressure units of measure.
Record up to ninety-nine (99) readings for each of the three
measurement types (Air Velocity, Air Flow, and Pressure) for a total of 297 readings.
USB port for connection to a Personal Computer (PC) for real time datalogging of up to 5500
readings stored on the PC.
Large backlit LCD display.
Data Hold and Maximum, Minimum, Average memory (MIN/MAX/AVG).
Auto Power OFF (can be disengaged).
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
3 HD350-en-GB_V3.4 2/19
Meter Description
1. Pitot tube. Hold the tube in the flow of air to take a reading
2. Pressure Manometer hose 1 Black
3. Pressure Manometer hose 2- White
4. Pressure Connector (+)
5. Pressure Connector (-)
6. Temperature sensor
7. LED display shows readings, units, setup
parameters, and user alerts
8. PC interface jack: Use the supplied
cable to connect the meter to a PC
9. Upper Keypad:
F/C : Press to change the unit of
measure for Temperature. Also
functions as an up arrow key
UNIT : Press to change the unit of
measure for Pressure, Air Velocity, and
Air Volume (Flow). Also functions as a down
arrow
AVG / REC: Used to obtain the
Average for multi-point measurements in
either FLOW or VELOCITY modes. Up to
twenty (20) points can be averaged.
Press and hold this button for 3
seconds to access the data Recall mode (REC)
SETUP : Momentary key presses turn the backlight on and off. Press and hold this button for 3
seconds to enter or exit the Setup mode (discussed later in this guide)
10. Lower Keypad:
MAX/MIN: Press to record and store the highest, lowest and continuous moving average readings
for single point measurements. Press and hold this button to exit this function
SAVE / CLEAR: Press to store a reading. In recall mode, pressing this button clears a data
sample.
P/V/F: Press to select Pressure (P), Air Velocity (V), or Air Flow (F)
HOLD / ZERO: Momentary presses freeze and un-freeze the displayed reading. Press and hold
the button to ZERO (OFFSET) the displayed reading
Note: the meter does not operate in the horizontal position. Keep it either in the vertical or
near vertical position and make your Zero offset at the same vertical position as you make
your measurements.
11. On/Off button : Press to turn the meter ON or OFF
KEYPAD NOTE: In Setup mode several buttons have special uses not detailed above but are
described in subsequent sections of the manual.
NOTE: Battery Compartment, Tilt Stand, and Tripod Mount are located on the reverse side of the
meter.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
4 HD350-en-GB_V3.4 2/19
Display Description
1. Elapsed timer display units (min:sec or hour:min)
2. Pressure, Velocity, Flow and Temperature
mode indicators
3. Primary Measurement Display
4. Units of measure for air velocity
5. Units of measure for pressure
6. Indication that the meter is communicating
with the PC
7. Auto Power Off mode indicator
8. Low battery indicator
9. Duct Shape indicator
10. Data Hold indicator
11. Height/Width (rectangular duct) or Diameter
(circular duct)
12. Setup mode indicator
13. CLEAR icon appears as data is deleted from
14. Reading (sample) number
15. Memory indicator
16. REC, MAX, MIN and AVG indicators
17. Temperature units for the primary display
18. Units of measure for air flow
19. Temperature units for the secondary display
20. Secondary display (Temperature)
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
5 HD350-en-GB_V3.4 2/19
Setup Mode
Changing Setup Options
The Setup mode is used to select the shape/dimensions of an air duct for Air Flow Measurements,
engage/disengage Sleep mode (auto power OFF), hide/view measurement types, and selectively
delete (clear) readings from the 99-location internal memory. The meter stores these settings in its
internal non-volatile memory.
Setup Options
Option Menu item Settings
Air Duct dimension units Unit Set duct dimension units to inches ( in
or cm )
Air Duct Shape Duct Shape Rectangle or Circular duct symbol
Air Duct Area DECI/99999 Decimal place and 5-digit number to
represent the area
Meter Configuration (select
the measurement parameters
to use; the others will be
hidden)
Type
Type 1 (show Pressure and Velocity)
Type 2 (show Velocity and Flow)
Type 3 (show all measurement types)
Auto Power Off (Sleep) mode SLEEP ON or OFF
Delete Stored readings ALL
Use the SAVE/CLEAR button to
choose the reading type(s) to delete.
Select CLEAR to delete.
Entering or Exiting Setup
Press and hold the SETUP button for 2 seconds to enter or exit the Setup mode. When the meter is
in Se .
Changing a Setup Option
1. Use the arrow keys to scroll through the setup options.
2. Press the AVG REC button when the desired setup parameter is displayed.
3. Use the arrow keys to scroll to the desired setting.
4. Press the AVG REC button to store the new setting in memory.
Note: The Setup mode is disabled when the meter is in the MIN-MAX-AVG mode.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
6 HD350-en-GB_V3.4 2/19
Air Duct Properties (for Air Flow Measurements)
Air Duct - Unit of Measure:
1. Press and hold the SETUP button for two (2) seconds to enter the Setup mode. The SETUP
display icon will appear.
2. Use the arrow keys to scroll to the UNIT display.
3. Press the AVG REC at the
bottom of the LCD in relatively small digits.
4. Use the arrow keys to change the unit of measure.
5. Press the AVG REC button to save the setting. Continue with Step 6 below to set the shape
and size of the duct.
Air Duct Shape:
6. Continuing from Step 5 above, press the AVG REC button to show the rectangle or circle
shape.
7. Use the arrow keys to select the shape that matches the air duct in question (rectangular or
circular duct)
8. Press the AVG REC button to store the setting and proceed to Step 9 to enter the air duct
area.
Air Duct Area (W x H) for Rectangular Ducts:
9. Continuing from Step 8 above. Skip to Step 18 for Circular ducts. For rectangular air ducts,
nd a
5-digit number directly below. The 5-
10. Use the arrow keys to move the decimal to the desired position
11. Press the SAVE CLEAR button to move the display cursor to the right-most digit. The right-
most digits will flash indicating that it is ready to be changed if desired.
12. Use the arrow keys to change the value of the right-most digits in the range of 0 to 9.
13. Use the SAVE CLEAR button to move to the next digit and change its value if desired using
the arrow keys. Continue in this manner until the duct width edit is complete.
14. Press the AVG REC button to store the Width value and move to the Height (H) editing
procedure.
15. Edit the Height value in the same manner as the Width value.
16. Press the AVG REC button to store the Height value.
17. Press and hold the SETUP
display icon will switch off.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
7 HD350-en-GB_V3.4 2/19
Air Duct Area (pi*r2) for Circular Ducts:
18. Continuing from Step 8 above. For circular ) will appear.
The display will show DECI (decimal) at the top and a 5-digit number directly below. The 5-
19. Use the arrow keys to move the decimal to the desired position
20. Press the SAVE CLEAR button to move the display cursor to the right-most digit. The right-
most digits will flash indicating that it is ready to be changed if desired.
21. Use the arrow keys to change the value of the right-most digits in the range of 0 to 9.
22. Use the SAVE CLEAR button to move to the next digit and change its value if desired using
the arrow keys. Continue in this manner until the duct diameter edit is complete.
23. Press the AVG REC button to store the Width value and move to the Height (H) editing
procedure.
24. Press and hold the SETUP
display icon will switch off.
Meter TYPE Configuration
The TYPE feature in the Setup mode allows the user to hide/view measurement types (Air Velocity,
Air Flow, and Pressure). The meter can be configured for Type 1 (show Pressure and Velocity
measurements); Type 2 (show Air Velocity and Air Flow measurements); Type 3 (show all measurement
types). The steps below outline the configuration process:
1. Press and hold the SETUP button for two (2) seconds to enter the Setup mode. The SETUP
display icon will appear.
2. Use the ar
3. Press the AVG REC butt at the top of the LCD.
4. Use the arrow keys to select the desired type number.
measurement types.
5. Press the AVG REC button to save the setting.
6. Press and hold the SETUP
display icon will switch off.
Auto Power OFF (Sleep) Mode
Sleep mode automatically switches the meter OFF after 20 minutes of inactivity. This feature goes a
long way in preserving battery life. To disengage/engage this feature:
1. Press and hold the SETUP button for two (2) seconds to enter the Setup mode. The SETUP
display icon will appear.
2.
3. Press the AVG REC
4.
5. Press the AVG REC button to save the setting.
6. Press and hold the SETUP
display icon will switch off.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
8 HD350-en-GB_V3.4 2/19
Delete (Clear) Stored Readings
As described in the dedicated section on th
up to ninety-nine (99) readings for instant recall. The CLEAR feature in the Setup mode allows the
user to selectively delete stored readings by type or to delete all of the readings.
1. Press and hold the SETUP button for two (2) seconds to enter the Setup mode. The SETUP
display icon will appear.
2. Use the ar
3. Press the AVG REC butt
4. Use the arrow keys t .
5. -VEL-
FLOW). Use the SAVE CLEAR button to select the measurement types to delete.
6. Press the AVG REC button to clear the selected reading types. The meter will beep indicating
that that the delete process was successful.
7. Press and hold the SETUP
display icon will switch off.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
9 HD350-en-GB_V3.4 2/19
Measurements
Pressure Measurements
1. Turn the meter ON using the power button .
2. Use the P/V/F button to scroll to the Pressure Measurement Mode ( PRESS
will appear).
3. The Primary display shows gauge or differential Pressure measurements (in the range of
±5000Pa) in the following units of measure (selectable): PSI, mbar, Pa, inH2O, and mmH2O.
To change the displayed unit of measure for Pressure, use the UNIT button.
4. Ambient Temperature readings will appear at the top right of the LCD on the Secondary display
digits. To change the displayed unit of measure for Temperature, use the F/C button.
5. For Gauge Pressure Measurements, connect a single hose to the INPUT (+) port and leave
the REF (-) port unconnected.
6. With the other end of the connected tubing open to ambient conditions, press and hold the
HOLD ZERO
7. Connect the attached hose to the pressure under test and read the displayed pressure value.
8. For Differential (Manometer) Pressure Measurements, connect tubing to the INPUT (+) port
and the REF (-) port. The meter will now display a positive pressure reading if the INPUT (+)
pressure is greater than REF (-) and a negative reading if REF (-) is greater than INPUT (+).
Air Velocity (Speed) Measurements
1. Press the PVF button to select the Air Velocity measurement mode; the VEL display icon will
appear on the LCD.
2. Use the UNIT button to select the desired measurement unit (m/s, ft/min, km/h, MPH,
knots).
3. The meter
secondary display digits (top right of LCD) displays the ambient temperature measurement.
4. Input (+) on the
Ref
(-)
of the Pitot tube.
5. If the Velocity measurement is a negative value on the display, ensure that the hoses are
attached to the correct ports on the Meter and the Pitot tube.
6. With the Pitot tube open to ambient conditions press and hold the HOLD ZERO button for 2
seconds to zero the display.
7. Put the mouth of the Pitot tube in the direction of the oncoming air mass under test and read
the Air Velocity measurement value on the LCD.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
10 HD350-en-GB_V3.4 2/19
Air Flow (Volume) Measurements
1. Press the P/V/F button to enter the Air Flow (Volume) mode (FLOW will appear on the LCD).
The Primary display area will show the Air Flow measurement.
2. Use the UNIT button to select the desired unit of measure (CMM or CFM).
3. To view the currently programmed duct area and shape:
Press the P/V/F button three more times to access the duct size/dimensions display. The
duct shape selection (rectangle or circle) will appear on the lower left-hand area of the LCD
and the Area value will be shown above it.
For Circular ducts, the Diameter (D) of the duct will be shown.
For Rectangular ducts, the Width value (W) will be shown first; press the P/V/F button again
to switch to the Height (H) value display.
Note that the Meter stores/displays the last duct shape and size programmed by the user.
To change the duct size and/or shape refer to the earlier SETUP MODE section.
Press the P/V/F button again to return to the AIR FLOW screen.
4. Now take an air velocity measurement as described in the previous section on Air Velocity
(ignoring the unit of measure discussions). The meter will display Air Flow (Volume) in Cubic
Feet per Minute (CFM) or Cubic Meters per Minute. The meter calculates Air Volume (Flow) by
measuring Air Velocity and taking into account the area of the duct.
Ambient Temperature Measurements
The Secondary display area (top right of LCD) indicates the ambient temperature sensed by the
thermometer located at the top middle of the meter (between the two pressure connection posts).
To change the displayed unit of measure for Temperature, use the F/C button.
The only instances where the Secondary display area will not indicate temperature are when the
meter is in the SETUP mode or when the Elapsed Timer is shown.
Additional Functions
Data Hold
1. Press the HOLD ZERO button to freeze the presently displayed reading on the display. The
display will show the HOLD icon while in the Data Hold mode.
2. Press the HOLD ZERO
to real time operation.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Autres manuels pour HD350
1
Table des matières
Autres manuels Extech Instruments Instrument de mesure
Extech Instruments
Extech Instruments HD750-NIST Manuel utilisateur
Extech Instruments
Extech Instruments 407790 Manuel utilisateur
Extech Instruments
Extech Instruments RPM33-NIST Manuel utilisateur
Extech Instruments
Extech Instruments MO55W Manuel utilisateur
Extech Instruments
Extech Instruments DT500 Manuel utilisateur
Extech Instruments
Extech Instruments CO260 Manuel utilisateur
Extech Instruments
Extech Instruments lcr200 Manuel utilisateur
Extech Instruments
Extech Instruments AN200 Manuel utilisateur
Extech Instruments
Extech Instruments EC210 Manuel utilisateur
Extech Instruments
Extech Instruments BT100 Manuel utilisateur
Extech Instruments
Extech Instruments Oyster 341350A-P Manuel utilisateur
Extech Instruments
Extech Instruments TB400 Manuel utilisateur
Extech Instruments
Extech Instruments MS400 Manuel utilisateur
Extech Instruments
Extech Instruments 407706 Manuel utilisateur
Extech Instruments
Extech Instruments HT30 Manuel utilisateur
Extech Instruments
Extech Instruments 451212 Manuel utilisateur
Extech Instruments
Extech Instruments MA610 Manuel utilisateur
Extech Instruments
Extech Instruments 407119 Manuel utilisateur
Extech Instruments
Extech Instruments HD700 Manuel utilisateur
Extech Instruments
Extech Instruments RH390 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur