Excell X Series Manuel utilisateur

X Series Weighing Scale

User Manual

The information contained herein is the property of EXCELL PRECISION CO., LTD. and is

supplied without liability for errors or omissions. No part may be reproduced or used except as

authorized by contract or other written permission. The copyright and the foregoing restriction

on reproduction and use extend to all media in which the information may be embodied.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

Table of Contents

PREPARING TO USE THE SCALE..............................................................................................2

PRECAUTIONS FOR USE...........................................................................................................2

CHAPTER 1 INTRODUCTION .....................................................................................................4

1-1 PRODUCTION INTRODUCTION ..................................................................................................4

1-2 DISPLAY DESCRIPTION ...........................................................................................................4

1-3 KEYPAD FUNCTIONS DESCRIPTION..........................................................................................5

1-4 POWER DESCRIPTION.............................................................................................................6

1-5 ERROR MESSAGES ................................................................................................................6

CHAPTER 2 GENERAL OPERATION DESCRIPTION ................................................................7

2-1 BACKLIGHT FUNCTION............................................................................................................7

2-2WEIGHING MODE ...................................................................................................................7

2-2-1 Units Selection (not available in 4 key model)..............................................................7

2-2-2 Zero Function ...............................................................................................................7

2-2-3 Tare Function ...............................................................................................................7

2-2-4 Net/Gross Function (only available in 4/5 key models).................................................8

2-2-5 Check Weighing Mode (4/5 key models need to set through F4).................................8

2-2-6 Totalizing (not available in 4/5 key models)................................................................10

2-3 COUNTING FUNCTION (NOT AVAILABLE IN 4/5 KEY MODELS).....................................................10

2-3-1 Sampling ....................................................................................................................10

2-3-2 Check Weighing .........................................................................................................11

2-3-3 Totalizing....................................................................................................................11

CHAPTER 3 GENERAL FUNCTION SETTING..........................................................................11

3-1 F4 CHECK WEIGHING CONFIGURATIONS................................................................................12

3-2 F5 RS-232 OUTPUT SETTING (OPTION)................................................................................13

3-3 F6 EXIT FUNCTION...............................................................................................................18

3-4 F7 INTERNAL VALUE DISPLAY MODE......................................................................................18

3-5 F8WEIGHT HOLD MODE SETTING.........................................................................................18

3-6 F11 ID CODE SETTING.........................................................................................................20

3-7 F12 PRINT KEY ( ) FUNCTION SETTING ..........................................................................20

3-8 F14 CUSTOMIZED HEADER SETTING (R N P6,R N P7)...........................................................21

APPENDIX 1 OPTION CARD DESCRIPTION............................................................................22

APPENDIX 2 LOAD CELL PIN...................................................................................................24

APPENDIX 3 7-SEGMENT DISPLAY CHARACTERS ...............................................................24

Check Firmware Version

Turn on scale and hold ZERO key during countdown. Display firmware version 02036.

Turn off scale and turn on scale and hold TARE key during countdown. Display

maintenance number XXX, which is ranged from 0~999. Turn off and turn on scale to

return to weighing mode.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

Preparing to Use the Scale

1. Locate the scale on a firm level surface free from vibrations for accurate weight readings.

Adjust the four leveling feet to centre the leveling bubble on the scale.

2. Avoid hot sunshine directly on the scale or near the exhaust port ofventilating system.

3. Please use a separate power source plug to avoid the disturbance of other electric

appliances.

4. There should be no weight on the scale when power is turned on.

5. Commodity should be placed at the centre of platter when being weighed, and its size should

not exceed the dimension of the platter.

6. Please warm the scale 15 ~ 20 minutes before using.

7. Please note that when symbol appears on the screen, the scale needs to be charged.

8. Any suggestion is warmly welcome.

Precautions for Use

(1) Please operate or charge the scale in an open area. Do not squeeze the power cord to avoid

wire on fire.

(2) Please keep scale in a cool and dry place. Do not store under high temperatures.

(3) Please keep the scale clean and free from insect infestation.

(4) Avoid impacting with other items or overloaded with excessively heavy weights (The load

must not exceed the maximum capacity of thescale).

(5) If the scale is not going to be used for some time, please clean it and store it in a plastic bag

in dry condition. A desiccant sachet may be included to prevent moisture from building up.

(6) Operating temperature: -10℃~ + 40℃

(7) It is recommended to be used indoors and in environments with a height of less than 2000m

(8) If the product is used in a manner not specified by the manufacturer, product warranty may

be limited.

Thank for your purchasing of our EXCELL Weighing

Scale. To guide you to use our product correctly, please

read this User Manual carefully to extend the life of

machine and to avoid error.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

Safety Instructions for Lithium Batteries

1. Please pay attention to the storage temperature of the product. Do not place it in a high

temperature environment. The ambient temperature should be less than 50C.

2. After installing the battery, if no display when power is turned on, please check whether the

battery polarity is reversed. The polarity must be installed correctly to avoid battery power

wasted away.

3. When the LED flashes in the charging state, it means there are the following abnormal

states, please check:

a) Battery is installed but the contact is poor, please check whether the battery is installed

properly.

b) Please check whether the polarity of the battery is reversed. When the polarity is reversed,

the LED will flash after charging for a period of time.

c) When battery is removed and the AC power cord is still plugged in, the LED will also flash.

When plugged in without the battery installed, there will be a slight frequency conversion

sound, which is normal and does not affect the use of the function.

4. When symbol appears, scale needs to be charged.

a) When charging, the red LED will light up. Please refer to 1-4 for estimated charging hours.

b) When the battery is fully charged, blue LED will light up.

c) After plugging in, the blue light will turn on after about 5 minutes of voltage detection if

scale is fully charged. The LED charging indicator is to indicate the status of the charging

process and whether the charging is working properly. To check the battery level, please

unplug the AC cable first and turn on scale, and then check the battery symbol displayed

in the lower left corner of the display. The number of bars under the battery symbol indicates

battery level. 0 bar means <= 10% when the low power warning symbol ( ) flashes to

indicate that scale needs to be charged.

5. Please operate or charge the scale in an open area. Do not squeeze the power cord to avoid

wire on fire. While charging, the temperature of battery should below 45℃.

6. Our product uses a single-cell cylindrical 18650-3.7V lithium-ion battery, please pay attention

to the specifications of the battery. Battery capacity is not restricted.

7. If the appearance of the battery is deformed, damaged, etc., please do not install it for the

safety of use.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

...

....

Pcs

Chapter 1 Introduction

1-1 Production Introduction

1. High performance A/D converter

2. According to different resolution to do linearity calibration

Ordinary resolution models (below 10000)

Do specification calibration first then do weight calibration

High resolution models (10000~30000)

Do linearity calibration firstspecification calibration weight calibration at last

3. LCD display with LED backlight, powered by battery or plug-in mains, automatic power-off

function to ensure the stability of the scale. When battery voltage is lower than the system

voltage, scale is automatically powered off to ensure the accuracy and stability of the scale.

4. Check Weighing function for high limit and low limit and OK range.

5. 4 HOLD functions including animal scale HOLD

6. Depending on actual space, a RS232 card and/or a relay card can be installed.

1-2 Display Description

High limit value

▼1

“Stable” indication

OK range within HI

and LO limits

▼2

“Pre-tare mode”indication

Low limit value

▼3

(M+) “Accumulation mode”indication

“kg”unit

▼5

( ) “Samples insufficient” indication

“lb”unit

▼6

( ) “Unit weight insufficient” indication

Pcs

Counting mode

▼7

“Viss” unit (Burma unit)

Percent indication

→O←

“Zero”indication

Net

“Net weight”

indication

For Dual Range Models, the indicator 5 and 6

will be defined as below:

▼6 is Range 1 ▼5 is Range 2

“Low battery

power”indication

0.3 uv/D high sensitivity

zero point adjustable range -2mV~ +5mV

Sampling speed 10 times/second

use range -4mV ~ +30mV

non-linear scale 0.01% full scale

load cell stimulate power source 5V DC ±2% 100mA

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

1-3 Keypad Functions Description

5 key (4 key model does not have UNITS key)

10 key

12 key

key and key are not available for 10-key models.

Key description

4/5 key

10 key

12 key

Other

variation

Net/Gross key

NET/GROSS

Loop select from the preset units

lb/kg

Preset weight and quantity for weight

check or quantity check

TGT SET

Accumulate weight or quantity

Tare to deduct the container weight

TARE

Set preset tare

Recall the totalization value, preset value

and pre-tare value

RE-CALL

Clear the totalization value, preset value

and pre-tare value.

Zero the scale.

ZERO

Press this key to input the numbers (0 ~

9) and to light up the backlight.

Press this key to print the total data and

to confirm

Go into counting mode.

COUNT or

Q’TY SET

Press this key to sample.

SMPL

Hidden backlight key at upper

left corner

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

1-4 Power Description

Power

Battery

18650 3.7V lithium battery

Plugged in

100~240V AC

Power consumption varies depending

0~100% backlight used (mA)

No backlight

75% backlight (factory default)

≈ 24

≈ 28

Scale has a built-in power saving function to extend usage time. Table below shows the battery

capacity and estimated usage time. Time may vary with different brands of lithium batteries and

are for reference only.

Battery capacity

2000mA

2500mA

3000mA

3200mA

3500mA

Average usage time

80~90

hours

95~105

hours

110~120

hours

120~130

hours

130~140

hours

Estimated charging time

≈2.5 hours

≈3 hours

≈3.5 hours

≈4 hours

≈4.5 hours

Assume 25% in use for average usage time. If use continuously, time will be reduced by ~40%.

Low Power Alarm

When symbol flashes, scale needs to be charged. To check the battery level, please

unplug the AC cable first, and check the battery symbol displayed in the lower left corner of

the display. The number of bars under the battery symbol indicates battery level. 4 bars mean

100%, 3 bars mean 75%, 2 bars mean 50%, 1 bar means 25%, and 0 bar means <= 10% when

the low power warning symbol ( ) flashes to indicate that scale needs to be charged. If not

charge immediately, scale auto shuts down within 5~10 hours or 1~2 hours with backlight. The

cut voltage is about 3.5V. Once it auto shuts down and enters the battery protection mode, it

must be charged before it can be used again.

Please recharge at once when the symbol shows in order to keep the weight accuracy.

1-5 Error Messages

oL Weight exceeds 9d of maximum capacity. (d=division)

E1 Zero value after power on is over +10% FS.

E2 Zero value after power on is less than -10% FS.

need to set C5 to 1 to have E1 and E2 warnings

E4 Unstable zero return, unstable over 10 sec. Press to leave E4.

E6 Zero is too high when calibrating. (over internal value 350,000)

E7 Zero is too low when calibrating. (under internal value 80,000)

E8 Resolution is set higher than factory setting. Send it back to us to unlock to set new

resolution.

E10The scale is not in level status.(only available with level detector equipment.)

- - - - - - For weight < -20d without tare or pretare device in operation.

OIML approval models need to set C5 to 1 to show “- - - - - -“

E10 Level Switch (option)

Make PCB J3 open circuit and connect signal to CN7 of PCB. Display shows E10 after 2

seconds and all keys stop working in the mean time. If you do not need level switch, make

J3 short circuit.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

Chapter 2 General Operation Description

2-1 Backlight Function

Press key to loop select the display backlight mode: Auto 1~4, bL. on, bL. oFF.

Auto 1~4 “Auto Backlight” mode. When the weight is over 10d or any key is pressed, the

backlight will be switched on. When the weight returns to zero (the weight on

platform is less than 10d), the display backlight will switch off after 10 seconds.

1~4 (25%~100% backlight) is the brightness selection. Default is 3 (75%).

bL. On Display backlight is on all the time.

bL. oFF Display backlight is off.

2-2 Weighing Mode

2-2-1 Units Selection (not available in 4 key model)

1. After indicator is turned on, use UNITS key to select a unit from kg, lb, tael or viss, as

the screen indicated.

2. The selected unit will be memorized when you turn the indicator off. And the

memorized unit will appear after you turn on the indicator next time.

2-2-2 Zero Function

Press key to re-zero the display with no load on the platter. When zero is set, the

( ) symbol will be displayed.

2-2-3 Tare Function

1. When the weight of the container is unknown ( )

Place the container on the platter, after stable and press key, the weight value

returns to zero and net indication ( ) is on.

Place goods into the container, then the indicator shows the net weight of goods.

Clear tare value

When removing the container and goods, the display shows the negative weight value

of the container. Then press key to clear tare value. The indicator returns to

zero and net indication ( ) is on.

Recall tare value

Press then key the display shows tare value

Multiple tare operation Users can continuously increase or decrease the tare value by

pressing the key.

The total tare value (tare value + pre-set tare value) can equal the full capacity of the

indicator.

2. When the weight of the container is known ( )

Press key and the display shows..

Use and keys to input weight value of the container. After finishing the

procedures, the net indication ( ) and pretare indication “”is on.

Place goods into the container, then the indicator shows the net weight of goods.

Clear pretare value

Press then key, and then press key to clear pretare value.

When indicator returns to zero, net indication ( ) and pretare indication “” are off.

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

Recall pretare value

Press then key the display shows pretare value

In Tare mode, the Preset tare function is disabled.

The indicators with two weighing ranges can NOT pre-set the tare value larger than the first

weighing range. For example: a 30 kg indicator is set by two weighing ranges. The first range

is 0 to 15 kg, and the second range is 15 to 30 kg. The pre-set tare value can not be larger

than 15 kg.

2-2-4 Net/Gross Function (only available in 4/5 key models)

In Tare mode, press key once to display gross value. Net symbol “▼”disappears, and the

gross value “▼” appears. Press key again, it displays net value, net symbol “▼”appears

and gross symbol “▼”disappears. Press key continually to display net value or gross

value. In tare mode, key is able to work. When it displays “▼”, all keys are disable except

2-2-5 Check Weighing Mode

(4/5 key models need to set through F4)

1. Preset “ High limit”, “Low limit” and “ Beeper value” operation

Use and key to preset values.

For example:

Preset “Low limit” ( Low limit 10d ) e.g. Low limit = 20 kg

Press key the display shows.

Press key 1 time the display shows .

Press key 2 times the display shows .

Press key 4 times the display shows . 

Preset “High limit” ( High limit Low limit ) e.g. High limit = 25 kg

Press key 1 time the display shows.

Press key 1 time the display shows .

Press key 2 times the display shows .

Press key 1 time the display shows .

Press key 5 times the display shows .

Press key 3 times the display shows . 

Preset “Beeper value” ( Refer to Note ) e.g. Beeper value = 22

Press key 1 time the display shows 

Press key 2 times the display shows 

Press key 1 time the display shows 

Press key 2 times the display shows 

Press key 1 times the display shows .

Preset Single point (preset low limit only):

EXCELL PRECISION CO., LTD.

02036XXX ZSME300000422

After “preset low limit” procedures is completed and the display shows.,

then press key again, the display shows . . This means that the “preset

single point” procedure is completed.

NOTE

_ _ _ xx

A B

ASetting for the status that LCD is on and the beeper beep:

0 = when stable, the beeper beeps and LCD is on.

1 = when stable, the beeper beeps; whether stable or not, LCD is on.

2 = whether stable or not, the beeper beeps and LCD is on.

3 = open warning device: when the weight is higher than HI value and the weight is

stable, LCD is on and Relay Card open.

B Setting for the beep status:

0 = No beep

1 = OK (when the weight is over Low Limit & under or equal to High Limit.), the beeper

beeps.

2 = When the weight is under or equal to Low Limit & over High Limit, the beeper beeps.

Under Status in Preset Low Limit (preset single point only)

The BEEP, LCD mode should be fixed as follows:

When over “Low Limit”, the beeper beeps and is off

Whether stable or not, the beeper beeps and LCD indication is on

Warning device setting (not available in 4/5 key models)

Set HI value and value of the beep, LCD mode should be fixed as follows:

A 

When the weight equals to HI value, Relay Card open and the weight is accumulated. Press CE

key to dismiss the warning sound and the range of accumulated weight is [000.000]~[999999].

Clear warning accumulation (not available in 4/5 key models)

Press key first and then press key to clear all accumulated data.

Accumulated data is cleared automatically under following conditions

a. when shift among weight mode, counting mode and warning accumulation mode.

b. when shift the units

c. turn off the scale

LCD indication:     

 

10d Low Limit High Limit

◆To exit preset mode, please press key.

2. Recall Check-weighing Values (not available in 4/5/10 key models)

Press key then press key Recall “Low limit value”

Then press key again Recall “High limit value”

Then press key again Recall “Beeper value”

Then press key again Back to the beginning

3. Clearing Check-weighing Values (not available in 4/5/10 key models)

Press key then press key, and then press key Recall “Low limit

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Excell Échelle

Excell

Excell 20key-6PS Manuel utilisateur

Excell

Excell Ocean Manuel utilisateur

Excell

Excell KWH3 Manuel utilisateur

Excell

Excell Dingo EX2002 Manuel utilisateur

Excell

Excell H3 Series Manuel utilisateur

Excell

Excell ESW-E Manuel utilisateur

Excell

Excell GTW Manuel utilisateur

Excell

Excell Counting Scale Manuel utilisateur

Excell

Excell SI-130 Manuel utilisateur

Excell

Excell High Precesion Counting Scale Manuel utilisateur

Excell

Excell HJP Manuel utilisateur

Excell

Excell SUBe AirCharge Manuel utilisateur

Excell

Excell ESW-3 Manuel utilisateur

Excell

Excell 150 Series Manuel utilisateur

Excell

Excell 20key-35PS Manuel utilisateur

Excell

Excell SK-VET Manuel utilisateur

Excell

Excell YSP Manuel utilisateur

Excell

Excell AM4Series Manuel utilisateur

Excell

Excell SI-132 Manuel utilisateur

Excell

Excell YSW-5E Manuel utilisateur

Excell

Excell H3 Series Manuel utilisateur

Excell

Excell ELW Max Manuel utilisateur

Excell

Excell Weighing Scale Manuel utilisateur

Excell

Excell 14key Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur