Eurolube 53430 Manuel utilisateur

English Manual for TSM-module 53430, R10, 181008

LUBE-MASTER R10

R10

TSM MANUAL

TANK SURVAILLANCE MODULE

53430

LUBE-MASTER R10

2(21)

Table of Contents

1. INTRODUCTION 3

2. MECHANICAL INSTALLATION 3

3. ELECTRIC INSTALLATION 3

3.1. THE MAIN MODULE 3

3.2. CONNECTION ADAPTER (203 03 17) 5

3.3. LID INDICATOR BOARD (203 03 03) 5

4. CONFIGURATION 6

4.1. CHECK BEFORE CONFIGURATION 6

4.2. ADDRESSING THE TSM 6

4.3. SET-UP MODE 6

4.4. CHANGE ADDRESS [TCM//ADDRESS]6

4.5. RECOMMENDATION FOR SETTING ADDRESSES 7

5. CONFIGURE THE PORTS 7

5.1. CONNECT A TANK TO A PORT [TCM//PORTX/TANK]7

5.2. SET THE MASK [TCM//PORTX/MASK]7

5.3. ANALOGUE SENSOR SETTINGS 8

5.3.1. Set the input signal filter time constant .............................................................................................8

5.3.2. Adjusting the offset ............................................................................................................................8

5.3.3. Adjusting the calibration ...................................................................................................................8

5.3.4. Set sensor full scale ...........................................................................................................................9

5.4. FLUID SPECIFICATION 9

5.4.1. Set fluid name....................................................................................................................................9

5.4.2. Set fluid part number.........................................................................................................................9

5.4.3. Set the fluid density..........................................................................................................................10

5.5. TANK SPECIFICATION 10

5.5.1. Set tank capacity..............................................................................................................................10

5.5.2. Set the tank reorder volume level ....................................................................................................10

5.5.1. Set the tank stop volume level..........................................................................................................11

5.5.2. Set tank bottom area........................................................................................................................11

5.5.3. To configure a TSM port for a tank that does not have a constant area .........................................11

5.6. DISPLAYING TANK CONTENT ON A LED DISPLAY 12

5.6.1. Set LED address ..............................................................................................................................12

5.6.2. Set LED update interval ..................................................................................................................12

5.7. SET THE TYPE OF TANK (PC SYSTEM). 13

6. MENU TREE 14

7. FAST MENU CODES 15

8. TECHNICAL SPECIFICATION 16

9. TO CONNECT DISCRETE LEVEL SENSORS 53132/138/171 AND SOLENOID VALVES 17

9.1. FRESH OIL TANK,53138 (2-LEVELS) 17

9.2. FRESH OIL TANK,53171/53183 (1-LEVEL) 17

9.3. WASTE OIL TANK,53132 (2-LEVELS) 17

9.4. ONE TSM PORT CONTROLS A NUMBER OF PUMPS 18

10. EX-BARRIER 53187 FOR DISCRETE LEVEL SENSORS. 18

10.1. CONNECTING A WASTE OIL TANK 53132 (2-LEVELS) 19

11. TO CONNECT AN ANALOGUE SENSOR 19

11.1. ANALOGUE SENSOR 53417 19

11.2. CONNECTING AN ANALOGUE SENSOR. 20

12. EX-BARRIER 53188 FOR ANALOGUE SENSORS. 20

12.1. CONNECTION 21

13. MPDM PCB MOUNTED IN A TSM BOX 21

LUBE-MASTER R10

3(21)

1. Introduction

The LUBE-Master TSM module, (Tank Surveillance Module), is used to control pumps and/or measure levels in tanks

using floater based level switches. A TSM can be used both for fresh and waste oil tanks.

The TSM (53430) is based on a TCM 53408 but has a lid (p/n 203 03 11) with a led indicator board (p/n 203 03 03)

and a connector adapter (p/n 203 03 17) added to the main board 203 02 91.

Earlier models than serial number 12-02000 can be made with either a MPDM (53400) with another software ( chip

labeled TSM 1.xx.xx) and/or have a lid with chassis mounted indicator led’s. Because of this a lot of this manual also

in most parts covers older modules. Some features may be missing and some default settings may be different.

NOTE! The LUBE-Master installation manual should be available when installing and configuring a

TSM.

2. Mechanical installation

The TSM is delivered mounted in a metal box with power supply. It can also be delivered as a spare part PCB (p/n 203

03 91) .

Complete TSM in a box is mounted on a wall or other suitable place using the four-ø5 mm holes in the bottom corners

of the box.

If a PCB is used it is important that a power supply with enough performance is used, 24VBC 5A.

3. Electric installation

3.1. The main module

The TSM should be connected to mains 230VAC/50Hz using phase, neutral and ground.

Eurolube recommend that the connection is done through a 2-pole lockable working switch.

The “knock-out” holes on the lower right hand (see picture) should only be used for mains power supply to separate

mains from the circuit board (DC) side of the module.

The TSM is equipped with a switched power supply of 150W that can be set for 110VAC/60Hz or 230VAC/50Hz

by the internal switch shown by the yellow sticker.

It has five connectors (A) for the LUBE-Master communication. Two of these connectors, MPDM IN and MPDM

OUT are not connected to +24V and are intended for a connection to another TSM, MPDM or other modules that

already have +24VDC. This is to prevent connecting +24VDC from two power supplies.

LUBE-MASTER R10

4(21)

The other three connectors are used to connect external devices without a power source such as a Printer Module

(PM), a LED Module (LED) and/or a KeyPad (KP). These connectors can only supply power to a single device. For

more detailed information see the LUBE-Master Manual

NOTE! If the communication loop begin in one of these modules it must be connected to either MPDM IN or

MPDM OUT or +24V must not be connected.

The RESET-button (B) can be used to reset the module or reset the module address.

Power supply is connected to the connector (C).

NOTE! Check polarity, GND is closest to the hole!

The connector (D) is used when you install a chassis-mounted key switch and

diode. With the key switch you can set the status of the module to OFF-,

NORMAL-, or OVERRIDE-mode. The diodes indicate setting.

There are four connectors (E) market +24 V, OC, A, B and GND, one

for each pump/tank. Solenoid valves and level sensors are connected

to these connectors.

“A” of a TSM port is connected to “order oil/emptying” of the level

sensor.

“B” of a TSM port is connected to “Stop level” of the level sensor.

“GND” of a TSM port is connected to common of the level sensor.

“+24V” of a TSM port is connected to one of the terminals of a

solenoid valve and “Sol” is connected to the other.

TIP! If a TSM is used for a tank containing flammable liquid it could be necessary to use an EX

protection.

There are two diodes (F) for every port. These indicate the status of entry points A and B, the level in the tank.

One diode (G) on each port indicates if the solenoid valve is open or not.

If the diode (H) is flashing the

module is operational and

working properly. A steady

light or completely off indicates

a problem.

DIL switches for termination

and BIAS are located at (I). (J)

Shows the position of the

replaceable communication

driver. The SetupLock jumper

at position (K) has no function

for a TSM.

A LED (L) shows if an

analogue sensor is detected or

not, lit if detected. The analogue

sensors are connected to the 2-

pole connectors marked (M).

The polarity is marked on the

PCB.

TSM200

PCB 203 02 91X

with chip TSM 2.xx.xx.

ALARM

Solenoid valve

STOP

+24 V

GND

Sol

LUBE-MASTER R10

5(21)

3.2. Connection adapter (203 03 17)

To simplify the connection of the level sensors and the pump controllers there are a connection adapter inserted in

the main board port connectors. It splits each port connector into two identical connectors, one for the indicator

board in the lid and one for the level sensors and pump controllers.

This enables the possibility to fully remove the lid in an easy way but still keep the control functionality of the

module.

3.3. Lid indicator board (203 03 03)

By the indicator board mounted in the lid of the module the status of the discrete level sensors and the pump control

can be seen from the outside.

The indicator board is powered by the Port 1 inter connection cable. If the board has power (24VDC) the power led

(see picture) will be lit.

The 8-pole SIL-switch block can be used to invert the LED output compared to the sensor/pump signal. This can be

used depending on the NC/NO of the sensor and pump control used.

The SIL-Switch stock default for TSM 53430 is all ON. This is shown by the text to the left of the switch block in

the right picture above.

NOTE ! Never disconnect or connect the lid indicator board when power is on. Doing that could cause

damage to the lid indicator board.

LUBE-MASTER R10

6(21)

Reel:SETUP ‡

EXIT STOP CE ENT

PASS:_ ‡

Enter Password

Addr:8???_ ‡

Address[CODE]

TCM: ‡

TCM MainMenu

TCM: ‡

TCM MainMenu

Address:8XXX ‡

Ange Adress 8???

Address:8XXX ‡

Set Address 8???

4. Configuration

An LUBE-Master configuration sheet should always be filled or altered during the configuration.

NOTE! To obtain technical support a copy of the configuration sheet for the complete installation must be

sent to Alentec & Orion AB at

E-mail: lubemaster@alentec.se

Post: Alentec & Orion AB

LUBE-Master Support Team

Grustagsvägen 4

SE-138 40 Älta

SWEDEN

4.1. Check before configuration

Check that the TSM is working and communicating with the system according to the LUBE-Master Manual chapter

Testing modules.

NOTE! Do not forget to check and adjust the termination and BIAS according to LUBE-Master

Manual.

4.2. Addressing the TSM

A new module has a default address when delivered such as MPDM 1000, PM 2000, KP 3000, LED 4000, TSM

8000 and so on. To set an address for a new TSM or a TSM with unknown address press and hold its RESET button

for 5 seconds to set a temporary address. Immediately enter set-up mode from a KP and type 0 and then ENTER to

get to the Main menu of the TSM, see below.

NOTE! Only one new module can be installed at a time. If you press the RESET-button on several

terminals simultaneously or in a sequence, only the most recently pressed will be active.

TIP! Follow preferably”Recommendation for setting new addresses” when setting addresses.

4.3. Set-Up mode

Type the word ”SETUP” on a KeyPad and press ENTER.

Type the password and press ENTER.

Type the address for the TSM that is to be configured and press ENTER to access

its main menu. It is possible to add the 4-digit menu code to go directly to the

desired menu.

Scroll through the TSM sub menus by pressing or . When the desired menu is

shown press ENTER etc. On display it shows TCM because the TSM and TSM

share the same software.

4.4. Change address [TCM//Address]

Enter menu [TCM//Address] by pressing ENTER.

Press ENTER to get the cursor.

Type in the desired address and acknowledge by pressing ENTER. When the

cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode.

NOTE! If two or more TSM’s have the same address the system will fail. The TSM’s has to be re-addressed.

LUBE-MASTER R10

7(21)

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

Mask:X ‡

Set Mask 0-15

Mask:X ‡

Set Mask 0-15

Mask:X ‡

Set Mask 0-15

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

Tank:X ‡

Set TankNo ???

Tank:X ‡

Set TankNo ???

Hint! Follow preferably ”Recommendation for setting addresses” when setting addresses.

4.5. Recommendation for setting addresses

Each module demands a unique 16 bit hexadecimal address. There are

some forbidden and some reserved addresses but it is possible to use

all addresses between 0001 and 9999. To make it easier to upgrade

and support the system we recommend using the chart to the right.

This means that the first TSM should have the address 8001 and the

next one 8002 etc. It is a good idea not to use the default address

8000, it makes it easier to add new Tam’s

NOTE! It is essential to add modules to the configuration sheet

continuously as they are configured to avoid collisions.

NOTE! Address 0000 is forbidden and addresses above 9999 are reserved for the system.

5. Configure the ports

A TSM has four ports that are used to control four different pumps/tanks.

5.1. Connect a tank to a port [TCM//PortX/Tank]

To set a tank number for a port, from the main menu.

Enter menu [TSM//PortX] by scrolling with or .

At PortX: press ENTER.

Press ENTER to get the cursor.

Check the number of the tank that is connected to portX, type that number in and

press ENTER to acknowledge. When the cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode.

5.2. Set the Mask [TCM//PortX/Mask]

Using the Mask each tank function can be set. This is done by

adding the values for the desired functions, in the chart to the right.

EXAMPLE: Port 1 measures the level of a waste oil tank and

controls the air to a waste oil pump using an Eurolube 2-levels

sensor 53132. This is up done by calculating the value of the Mask 1+4+8=13. The

Mask should be set to 13.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to Mask: using or .

Press ENTER to get the cursor.

Type the mask value and press ENTER to acknowledge. When the cursor

disappears it is finished.

Press EXIT two times to leave Set-Up mode.

Adress Module

0000 Forbidden

1000 –1xxx MPDM

2000 –2998 PM

2999 PC-database

3000 –3xxx KeyPad

4000 –4xxx LED-display

5000 –5xxx PLC-modules

6000 –6xxx Reserved

7000 –7xxx Reserved

8000 –8xxx TCM

9000 –9xxx Others

A000 –FFFF Forbidden

Function Value

Waste oil tank 1

Not in use 2

Invert B 4

Invert A 8

LUBE-MASTER R10

8(21)

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

O:0.000 ‡

Zero adjust

O:-0.120_ ‡

Zero adjust

O:-0.120 ‡

Zero adjust

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

C:1.000 ‡

Calibration

C:1.000 ‡

Calibration

C:1.000 ‡

Calibration

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

T:6 ‡

Time constant

T:6 ‡

Time constant

T:6 ‡

Time constant

5.3. Analogue sensor settings

5.3.1. Set the input signal filter time constant

This time constant (Tau) is used to filter the sensor signal to create an

accurate tank level. “0” means no filter and a higher value gives slower

response but a more accurate value. The default value of “6” is in most cases

good. It means that for a step in the tank level the reading of the level is on

99,9 % after 30 seconds.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to T: using or .

Press ENTER to get the cursor.

Type the time constant and press ENTER to acknowledge. When the

cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode.

5.3.2. Adjusting the offset

Offset adjusting is used to obtain “0” volume when the tank is empty. If the

sensor 53417 is used a normal value is –0.080. The “-“ sign is typed on the

keypad by first pressing down arrow (yellow) two times followed by the “?”

mark.

If the tank is empty, put the sensor in the tank at the bottom. If there is fluid

in the tank hold the sensor outside the tank at bottom level. Adjust the offset

value until the tank level shows “0”.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to O: using or .

Press ENTER to get the cursor.

Type the offset value and press ENTER to acknowledge. When the cursor

disappears it is finished.

Press EXIT two times to leave Set-Up mode.

5.3.3. Adjusting the calibration

The calibration factor should normally be set to “1.018” if all other values

are set properly. The intention with the calibration factor is to set the

amplification so that the analogue input of the port matches the sensors

output.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to C: using or .

Press ENTER to get the cursor.

Type the calibration value and press ENTER to acknowledge. When the

cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode

LUBE-MASTER R10

9(21)

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

FN: ‡

Name (max 16 ch)

FN:_ ‡

Name (max 16 ch)

FN:Name ‡

Name (max 16 ch)

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

FP: ‡

Part number

FP:_ ‡

Part number

FP:XXXXXXXXX ‡

Part number

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

SFS:0.400 ‡

Full Scale [bar]

SFS:0.400 ‡

Full Scale [bar]

SFS:0.400 ‡

Full Scale [bar]

5.3.4. Set sensor full scale

The sensor full scale value is the pressure corresponding to 20 mA. If a

pressure sensor is used the value should be in [bar]. For sensor part number

53417 the value should be as default “0.400”

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to SFS: using or .

Press ENTER to get the cursor.

Type the sensor full scale value and press ENTER to acknowledge. When

the cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode.

5.4. Fluid specification

5.4.1. Set fluid name

The fluid name set in the TSM makes it possible to show the fluid name in

the info box for the graphic representation of the analogue sensor. It should

be set to the same value as in the PC database.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to FN: using or .

Press ENTER to get the cursor.

Type the name of the fluid and press ENTER to acknowledge. When the

cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode

5.4.2. Set fluid part number

The fluid part number set in the TSM makes it possible to show the fluid

part number in the info box for the graphic representation of the analogue

sensor. It should be set to the same value as in the PC database.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to FP: using or .

Press ENTER to get the cursor.

Type the part number of the fluid and press ENTER to acknowledge.

When the cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode

LUBE-MASTER R10

10(21)

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

D:1.000 ‡

Density [kg/L]

D:1.000 ‡

Density [kg/L]

D:1.000 ‡

Density [kg/L]

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

TankVol:1000 ‡

Set max vol [L]

TankVol:1000 ‡

Set max vol [L]

TankVol:1000 ‡

Set max vol [L]

TCM: ‡

TCM MainMenu

PortX: ‡

TCM MainMenu

ReVol:1000 ‡

Reorder vol [L]

ReVol:1000 ‡

Reorder vol [L]

ReVol:1000 ‡

Reorder vol [L]

5.4.3. Set the fluid density

If a pressure sensor is used it is essential to set the true density of the fluid

because the pressure at the bottom of the tank depends on fluid level and

fluid density. The density is about 1 Kg/l and for water and 0.875 Kg/l for

mineral oil at 20°C.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to D: using or .

Press ENTER to get the cursor.

Type the Density and press ENTER to acknowledge. When the cursor

disappears it is finished.

Press EXIT two times to leave Set-Up mode

5.5. Tank specification

5.5.1. Set tank capacity

The tank capacity set in the TSM is used to create a true graphic

representation of the analogue sensor status. It should be set to the same

value as in the PC database.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to TankVol: using or .

Press ENTER to get the cursor.

Type the capacity of the tank and press ENTER to acknowledge. When the

cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode

5.5.2. Set the tank reorder volume level

The tank reorder volume set in the TSM is used to create a true graphic

representation of the analogue sensor status and start auto warning if that is

enabled. It should be set to the same value as in the PC database.

Enter menu [TCM//PortX] by scrolling with or .

At PortX: press ENTER.

Scroll to ReVol: using or .

Press ENTER to get the cursor.

Type the reorder volume level of the tank and press ENTER to

acknowledge. When the cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode

Table des matières

Autres manuels Eurolube Unité de contrôle

Eurolube

Eurolube 53408 Manuel utilisateur

Eurolube

Eurolube 53402 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur