Euri EOL-WL56BLK-1220cec Manuel utilisateur

WARNINGS CAUTIONS

• Risk of fire / electrical shock

• LED Fixture installation requires knowledge of luminaire electrical

systems.

• Risk of electric shock – disconnect power at source before installation

• Do not make or alter any open holes in an enclosure of wiring or

electrical components during installation.

• If lamp or luminaire exhibits abnormal operation (buzzing, flickering,

minimal light, etc.), turn off power, remove fixture and contact us. For

more information please visit www.eurilighting.com or call our toll-free

number 1-888-743-5766.

• Do not use with dimmers.

• Do not look directly at the operating LED Fixture.

• Do not touch this product with wet hands.

• Do not disassemble, repair or alter lamp.

• Designed for outdoor applications only.

• Suitable for wet locations.

• The luminaires shall be grounded.

• Be careful not to touch the lamp pins to the metal housing

when installing.

• This Device is not intended for use with emergency exits or

emergency lights.

INSTALLATION GUIDE

MODEL #: EOL-WL56BLK-1220cec

For customer service please call us at 1-888-743-5766

Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday

Questions?



LED Fixtures | Outdoor Wall Light Series

Lantern Class

1. Fix the crossbar to the

junction box with screws.

(See Figure 01)

2. Use the wire nuts to connect the white power line to the white power

line from the wall. And do the same to the black power line.

Connect the grounding wire from the fixture to the grounding wire from

the wall, and fix the grounding wire to the green screw. (See Figure 02

or wiring diagram above.)

3. Secure the fixture onto the crossbar with screws.

4. Screw included LED bulb into the socket.

(See Figure 03)

PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS

LISTED BELOW PRIOR TO PROPER INSTALLATION

wall

Junction box Crossbar

LED Bulb

IR sensor

fix the grounding wire here

grounding

wire

grounding wire

power lines

wire nut

power lines

SAFETY INSTRUCTIONS

Fig.1 Fig.3

Fig.2

INSTALLATION GUIDE

MODEL #: EOL-WL56BLK-1220cec

For customer service please call us at 1-888-743-5766

Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday

Questions?



PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS

LISTED BELOW PRIOR TO PROPER INSTALLATION

LED Fixtures | Outdoor Wall Light Series

Lantern Class

SPECIFICATIONS OF PIR DUAL SENSOR

CUSTOMIZATION OPTIONS:

Function and Operation

Choose a mode by sliding the switch on the bottom of the backplate

of the fixture. When power is first applied, the light will turn on

immediately. Wait for 20 seconds to allow the sensor to warm up.

1. TEST MODE (daytime and nighttime operation.)

The light will turn to low-level brightness (50% brightness). The light

will turn to high-level brightness (100% brightness) when motion is

detected, and stay on as long as the motion is continuing. The light

will revert to low-level brightness about 5 seconds after motion is no

longer detected.

2. AUTO MODE (nighttime operation only; on at dusk, off at dawn)

At dusk, the light will turn to low-level brightness (50% brightness).

The light will turn to high-level brightness (100% brightness) when

motion is detected, and stay on as long as the motion is continuing.

When the motion stops, the light will remain on for the predetermined

time set (5 ~ 300 seconds), and then revert to low-level brightness.

The light will turn off automatically at dawn.

3. D2D MODE (nighttime operation only; on at dusk, off at dawn)

The light will turn to high-level brightness (100% brightness) at dusk.

It will turn off at dawn.

Shut-off Delay

The Shut-off delay is the length of time the light will stay at high-level

brightness after motion has ceased to be detected. This Shut-off delay

can be set when the operation is in “AUTO” mode by using the “TIME”

knob located on the left side of the panel at the bottom of the backplate

(See Fig.5).

To increase the shut-off delay, turn the knob clockwise. To decrease

shut off delay, turn the knob counterclockwise. The delay may be

adjusted from a minimum of 5 seconds to a maximum of 5 minutes.

The light will stay on as long as motion is detected continuously and

will automatically turn to low-level brightness when no more motion is

detected after the delay time has passed.

The sensitivity of the Motion Sensor

The sensitivity of the motion sensor can be adjusted by using the

“SENSITIVITY” knob located on the right side of the panel at the bottom of

the backplate (See Fig.5). To increase sensitivity, turn the knob clockwise.

To decrease sensitivity, turn the knob counterclockwise. The sensitivity

may be adjusted from a minimum of 5 feet to a maximum of 30 feet.

4.Manual Override Mode (6-hours auto Rest)

To shift to the manual override mode, set the switch to” AUTO” Mode.

Turn the wall switch“OFF” and then turn it“ON” within 2 seconds. The

light will remain on for 6 hours. To shift back to the“AUTO” mode, turn

the wall switch “OFF” and then turn it “ON” within 2 seconds again.

(See Fig.4)

Auto Mode

Manual

Override

Mode

Turn wall switch

Note: To make sure the above functions operate properly, always

keep the wall switch in the “ON” position (including the daytime).

The light will turn off automatically at dawn

TIME SENSITIVITY

TEST AUTO D2D

Manual Override Operation Diagram

OFF-ON within 2 sec.

Reset automatically aer 6 hours

Fig.5

Fig.4

SPECIFICATIONS OF PIR DUAL SENSOR

SELECTING A LOCATION:

SELECTING A LOCATION (CONTINUED):

TEST THE LIGHT FIXTURE

INSTALLATION GUIDE

MODEL #: EOL-WL56BLK-1220cec

For customer service please call us at 1-888-743-5766

Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday

Questions?



PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS

LISTED BELOW PRIOR TO PROPER INSTALLATION

LED Fixtures | Outdoor Wall Light Series

Lantern Class

FEATURES:

1. MOTION SENSOR FUNCTION-At dusk the Light fixture will be turn on for

a low-level illumination. When the motion sensor detects any moving heat

sources(such as people and vehicles), the Light fixture will be switched

from the low-level illumination to a high-level illumination for a short

duration time. After the short duration time, the light returns to the low-level

illumination until to dawn for saving energy.

2. MANUAL OVERRIDE-The user many manually tum on the light from

inside his home using a wall switch.

3. Uses a 17W dimmable LED light bulb.

1. When selecting a location, be aware of the motion sensor’s maximum

range of 30 ft and 150° detection angle (Fig.6). In addition, be aware of its

25° detection down-angle(from

horizontal) (Fig.2). Mounting the fixture too high or in front of a sloped

surface, such as an uphill walkway or driveway, may affect the motion

sensor’s effectiveness.

2. Select locations away from heat sources, such as heating vents, air

conditioners, and heated swimming pools.

1. When selecting a location, be aware that the motion sensor is more

sensitive to movement across its coverage area and less sensitive to the

movement toward or away from the motion sensor (Fig.7)

2. Select locations away from nighttime light sources, such as street lamps

or other light fixtures. They may shine light onto the fixture’s photocell

sensor(located beneath the sensor), this light might cause the circuit

to“think” that it is daytime and not allow the fixture’s functions to operate.

3. Be aware that shade from a porch or an eave may not allow enough

daylight to shine onto the photocell sensor and may cause the circuit

to“think” that it is nighttime, and subsequently cause the light to come on

during the daytime.

4. Be aware that motorized equipment, such as power tools, on the same

electrical circuit, may cause oscillation on the electrical line which might

cause the fixture to malfunction

The sensitivity knob adjusts the amount of distance that is required to activate the unit. To set to a desired level of sensitivity:

1- Turn on the circuit breaker and the light switch. The sensor has about 20 seconds warm-up period before it will detect motion. When first

turned on, wait about 20 seconds.

2- Set the Time switch to the“TEST position and the Sensitivity knob set in the middle position of minimum and maximum position.

The lights turn off in about 5 seconds. Keep in mind a better sensitivity is achieved by walking across the coverage area, not walking towards or

away from the motion sensor.

SPECIFICATIONS:

Motion Sensor Range: Up to 30 ft(Varies with surrounding

temperature)

Sensor Detection Angle: 150°

Electrical Requirements: 120 VAC, 60HZ

Max Load: 26W LED dimmable Bulb

Insallation Height: 6.5+0.7 Ft (1.8-2.2M)

150°

Sensor Sensor

Fig.6

Fig.7

Manuels Éclairage extérieur populaires d'autres marques

Sealey

Sealey LED37 Manuel utilisateur

nordlux

nordlux VEJERS Guide de l'utilisateur

SImx

SImx ELITE LED LHTC637 Manuel utilisateur

GEV

GEV CAROLINE 10833 Manuel utilisateur

NEBO

NEBO NEB-LSP-0020 Manuel utilisateur

WE-EF

WE-EF PFL540 LED Manuel utilisateur

Lindby

Lindby 9949029 Manuel utilisateur

HEPER

HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation

HEPER

HEPER LW8034.003-US Instructions d'installation et d'utilisation

Maretti

Maretti VIBE S 14.6080.04.A Manuel utilisateur

BEGA

BEGA 84 253 Manuel

HEPER

HEPER MINIMO Instructions d'installation et d'utilisation

LIGMAN

LIGMAN BAMBOO 3 Manuel utilisateur

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur

urban ambiance

urban ambiance UQL1273 Manuel utilisateur

TotalPond

TotalPond 52238 Manuel utilisateur

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuel utilisateur