ETM ETM9900(J) Manuel utilisateur

Features:

◩ 3G (Tri-band HSDPA/UMTS) Connectivity

◩ Standard RS232 9DF serial port

◩ 6v to 35v power input on RJ12 connector

◩ 4(or 7) x digital, analogue or pulse I/O’s on RJ45 connector

◩ SMA M antenna connector

◩ Sleep Mode for reduced power consumption

Issue 27012009

Cinterion

HC25(HC28) Inside

ETM9900(J)

Quick Start Guide

HSDPA/UMTS/GSM/GPRS Terminal

Page 2 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Contents

Introduction....................................................................................................................................... 4

Nomenclature................................................................................................................................ 4

Overview. ...................................................................................................................................... 4

Applications................................................................................................................................... 4

Interfaces....................................................................................................................................... 4

Power Supply.................................................................................................................................... 5

RJ45 I/O Connector.......................................................................................................................... 5

Serial (RS232) Port........................................................................................................................... 6

Antenna............................................................................................................................................. 6

3V SIM Card ..................................................................................................................................... 6

Indicator Lights.................................................................................................................................. 7

Installation......................................................................................................................................... 8

Configuration Tool............................................................................................................................. 8

Introduction.................................................................................................................................... 8

Using the Right Version of the Configuration Tool........................................................................ 8

Using the Configuration Tool......................................................................................................... 8

Modem Initialisation Settings - Main Init Tab............................................................................... 10

Control Via ET Commands............................................................................................................. 10

Dry contact generated SMS alarm.................................................................................................. 12

Example ...................................................................................................................................... 12

Wiring Diagram............................................................................................................................ 12

Configuration Tool Settings......................................................................................................... 12

Temperature Alarm......................................................................................................................... 14

Example ...................................................................................................................................... 14

Wiring Diagram............................................................................................................................ 14

Configuration Tool Settings......................................................................................................... 14

Page 3 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Page 4 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Introduction

Nomenclature

ETM9900 incorporates the Siemens HC25 engine and is intended for use within Australia, NZ and

worldwide.

The ETM9900J variant incorporates the Siemens HC28 engine and is intended for use within

Japan on the Softbank network and global roaming.

Overview.

The ETM9900(J) is an industrial terminal designed for M2M (Machine to Machine) communications.

With Tri-band UMTS/HSDPA and Quad-Band GSM/GPRS/EDGE capability, the ETM9900(J) has

the versatility to operate on virtually any GSM or UMTS network.

Terminal Nomenclature/History

Model Comment Module Installed

ETM9900 First Release HC25 Release 1.0, 1.2, 1.78 or

2.05

ETM9900-1 Future Release HC25 Release 2.05, 7 x I/O’s

versus 4 x I/O’s for ETM9900

ETM9900J First Release Japan only unit HC28, 7 x I/O’s

Module Nomenclature/History

Model Comment

HC25 Release 1.0/1.2 Initial release

HC25 Release 1.78 Maintenance Release Australia and New Zealand Only

HC25 Release 2.05 Current Release

HC28 Release 1.03 Current Release

Applications

Typical applications include:

◩ Security;

◩ Automated Meter Reading (Telemetry);

◩ Interface to data acquisition/data logging systems;

◩ Broadcasting/updating multi-media files;

◩ Interfacing with alarm and control applications.

Interfaces

◩ RJ12 power connector

◩ RJ45 I/O connector

◩ RS232 interface (V.24/V.28 on the D-Sub socket)

◩ Antenna connector SMA Jack (female)

◩ Mini-SIM card holder

Page 5 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Power Supply

The ETM9900(J) power connection is a 6 pin RJ12 connector, pin allocations are shown below.

Pin Function

1 Power Supply (+6 to +35VDC)

2 Not Used

3 Not Used

4 Not Used

5 Not Used

6 GND

RJ45 I/O Connector

4 x I/O’s configurable as digital, analogue or pulse are available on the RJ45 connector, pin

allocations are as shown below.

Pin Function

1 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Pulse Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

2 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

3 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC

4 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC

5 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC

6 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC

7 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input ±50VDC

◩ Digital Output: LL0V/0.1mA, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC

8 GND

Caution

Take care to ensure that only the

correct connectors are used or

mechanical damage to the pins may

result.

I/O’s 5 thru 7 not

available on

ETM9900 Version 1

Page 6 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Serial (RS232) Port

The RS232 Port is the primary interface for the application software and connection to external

devices. AT commands are used to communicate with the terminal. The RS232 interface is

implemented as a 9-pin D-Sub socket with screw fittings.

Pin Function

1 DCD Out

2 RXD Out

3 TXD In

4 DTR In

5 GND

6 DSR Out

7 RTS In

8 CTS Out

9 RING Out

Antenna

The ETM9900(J) Terminal has a standard SMA Jack (Female) antenna Plug on the end of an

approximately 90mm cable.

3V SIM Card

The SIM card connector is located at the rear of the ETM9900(J) Terminal. Any SIM card used

needs to be correctly provisioned for the services and network upon which it is intended to be

used .

SMA Connector

Caution

Always disconnect power supply

before inserting or removing SIM

Card.

Care should be taken in inserting

and removing the SIM card so as

not to damage the SIMholder or

cover.

Page 7 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Indicator Lights

Blue/RedLED

(UMTS)

Function

Flashing LED flashes when the ME is registered to the UMTS network and either

awake or in power saving state.

While the STATUS1 (BLUE/RED) signal is active the STATUS0 (GREEN)

signal is inactive.

Off ME is not registered to the UMTS network.

YELLOW LED

(MCU)

Function

Flashing Communicating with the module HC25(HC28).

500ms On / 500ms

Off Waiting for Answer from Module HC25(HC28).

On When connected to an ISP and a Socket is established.

GREEN LED

(GSM)

Function

500ms On / 500ms

Off

Flashes at 1Hz and 50% duty cycle when the ME is awake and not registered

to any network.

2s On / 2s Off Flashes at 0.25 Hz and appr. 50% duty cycle when the ME is in power saving

state and not registered to any network. When the ME is in power saving

state and not registered, the flashing frequency may be less than 0.25Hz and

the duty cycle may vary, for example between 45% and 55%. These

variations are due to transitions from awake state to power saving state

which may occur at the beginning of an LED flashing period (eg. at the

beginning of a 1Hz or 0.25Hz flashing period). In the worst case, the LED will

indicate a transition from awake to power saving after 4s.

Flashing LED flashes when the ME is registered to the GSM network and either awake

or in power saving state.

While the STATUS0 signal is active the STATUS1 signal is inactive.

Off ME is not registered to the GSM network.

RED

UMTS YELLOW

MCU Status Green

GSM

ETM9900 Status LEDs

RED

UMTS YELLOW

MCU Status Green

GSM

ETM9900-1/9900J Status LEDs

Page 8 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Installation

1. Connect a standard RS232 modem cable 9DF to 9DM between the ETM9900(J) Terminal

and the external device or PC (a Serial/USB Adapter may be used if you computer does not

have a serial port).

2. Fit a suitable antenna to the ETM9900(J) unit.

3. Install a SIM card for enabled for the services you intend to use. If the terminal is intended

to be used for remote access to a device a terminating data number for Circuit Switch Data

(CSD) will need to be provisioned by the network operator, this number will usually differ

from any voice/SMS number. Note that for Telstra you will need to request;

◩ 2620 bearer capability (Telstra NextG™ Sims)

4. Connect the power supply. (The unit accepts a broad range of voltages from +6 to

+35VDC)

5. Refer the Common AT Commands section for recommended AT settings for the following

applications;

◩ SMS

◩ Circuit Switch Data

6. Refer to page 8 for instructions on configuring the unit for the intended application, SMS

alarm, IP connectivity etc.

Configuration Tool

Introduction

The HC25/HC28 engine used in the ETM9900(J) does not support storing of an active profile. A

configuration tool for the modem is available (FOC) upon request, that can be used to ensure that

a specified set of AT commands are always initialized at start-up.

Using the Right Version of the Configuration Tool

When the unit starts up and is connected to a terminal window and Escape is pressed (see below)

the version of the configuration tool will be shown as follows, check you have the correct

configuration tool for the unit – if you do not then download the correct one see page 3 for access

to downloads.

Using the Configuration Tool

It is recommended that you save the configuration tool on the computer you are using to configure

the ETM9900(J).

1. Start the Configuration Tool and go to the Terminal Tab on the screen.

2. Go to the Set Com Port Tab and select the Serial Port which will be used for the ETM9900(J).

3. Ensure the Port is open, click TAB to open if required

In this example the

appropriate

configuration tool is

CT03.00

Page 9 of 16

ETM9900(J) Quick Start Guide Issue 27012009

4. Place curser in the black area of the terminal window and click mouse to ensure the terminal

window is active.

5. Connect the ETM9900(J) to your computer using the serial cable.

6. Connect the power to the ETM9900(J) and repeatedly (usually three times) depress the ESC

key on your computer.

If successful the following message appears:

Escape Pressed

If unsuccessful repeat step 6.

Pressing escape disconnects the module and assists in Reading from or Writing to the unit.

7. Click on the Read EE Tab (Blue Arrow) to read current configuration. If first attempt to read is

unsuccessful, repeat.

8. Use the Main Init, Settings, Alarm / Message, I/O or other Tabs to enter required settings.

9. After you have re-configured the unit you need to write the commands to the terminal’s

EEPROM by pressing the Red arrow. If first attempt to read is unsuccessful, repeat.

10. Settings can be saved to a file on your PC. If you need to configure another ETM9900(J) with

the same settings this file can be loaded into the configuration tool and written to any

additional units that require the same settings.

The following configuration examples are provided in the following sections;

◩ Dry contact generated SMS alarm

◩ Temperature Alarm

Page 10 of 16

ETM9900(J) Quick Start Guide Issue 27012009

Modem Initialisation Settings - Main Init Tab

Modem AT Initialisation settings can be sent to the modem using the Main Init Tab.

AT^SCFG=“Radio/Band”,”X” (where X=band)

X=1, GSM 900MHz

X=2, GSM 1800MHz

X=16, WCDMA 2100MHz

X=64, WCDMA 850MHz (NextG™)

X=65, GSM 900MHz & WCDMA 850MHz

X=80, WCDMA 850/2100MHz

X=127, Default setting all bands

ATS0=2 Will set the unit to answer an incoming call after 2 rings, and may be useful for

applications using a Circuit Switch Data Call.

Control Via ET Commands

As default the ETM9900(J) is set to ET Command Mode, ET Commands are specific to ETM

terminals and allow for control, configuration and information requests to be sent to and from the

terminal. In ETM command mode AT commands cannot be sent to the unit.

ET commands can be sent via SMS or from configuration tool when directly connected or via an IP

or CSD connection. It is recommended that more complex settings such as changing messages or

phone numbers are made using the configuration tool.

Common ET commands are shown below, for a full ET command list download the relevant

documents from Docbanq (see page 3).

Table des matières

Autres manuels ETM Terminal tactile

ETM

ETM Purple Manuel utilisateur

ETM

ETM ETM8140-1 Manuel utilisateur

ETM

ETM ETM9420-1 Manuel utilisateur

ETM

ETM Purple Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur