ETM ETM9120-1 Manuel utilisateur

UMTS/GSM/GPRS Terminal – ETM9140-1

GSM/GPRS Terminal – ETM9120-1

Features:

◩ 3G (HSPA+/UMTS) Connectivity – ETM9140-1 only

◩ 2G (GSM/GPRS) Connectivity

◩ Standard RS232 9DF serial port

◩ 5v to 35v power input on RJ12 connector

◩ 7 x I/O’s on RJ45 connector

◩ FME M antenna connector

◩ Sleep Mode for reduced power consumption

◩ User configurable via configuration tool

ETM9120 9140 Configuration Tool Userguide201406RV001

Configuration Tool Userguide

Page 2 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

Contents

Contents............................................................................................................................................ 2

Document.......................................................................................................................................... 4

History........................................................................................................................................... 4

Relevant Documents..................................................................................................................... 4

Abbreviation .................................................................................................................................. 4

Introduction....................................................................................................................................... 5

Overview. ...................................................................................................................................... 5

Nomenclature................................................................................................................................ 5

Using the Configuration tool.............................................................................................................. 5

Installation..................................................................................................................................... 5

Initial Start-up and Programming................................................................................................... 6

Saving, reading and writing configuration files.............................................................................. 7

File (Menu Option)......................................................................................................................... 7

Alarm / Message Tab........................................................................................................................ 8

SMS phone numbers and user ID................................................................................................. 8

Latest Incoming SMS.................................................................................................................... 8

Unit ID added to messages........................................................................................................... 8

Use incoming security filter ........................................................................................................... 9

Maximum number of SMSs per day allowed to be sent................................................................ 9

Alarm Messages............................................................................................................................ 9

I/O Settings..................................................................................................................................... 10

IO 1 & 2........................................................................................................................................... 10

Delay before alarm is activated................................................................................................... 10

Alarm restore delay..................................................................................................................... 11

ET-cmd........................................................................................................................................ 11

SMS Alarm.................................................................................................................................. 11

UMTS/GPRS Alarm..................................................................................................................... 11

UDP Server Selection ................................................................................................................. 11

IO 3,4,5,6,7..................................................................................................................................... 11

Analogue Alarm Input.................................................................................................................. 11

A/D Cal Param ............................................................................................................................ 12

Power In Tab................................................................................................................................... 12

Power Source Monitor................................................................................................................. 12

Delay before alarm is activated................................................................................................... 12

Alarm restore delay..................................................................................................................... 12

ET-cmd........................................................................................................................................ 12

SMS Alarm.................................................................................................................................. 12

UMTS/GPRS Alarm..................................................................................................................... 12

UDP Server Selection ................................................................................................................. 13

Settings Tab.................................................................................................................................... 14

UMTS/GPRS Module <--> MCU and MCU <--> Port.............................................................. 14

Flow Control................................................................................................................................ 14

EEPROM Storage Area............................................................................................................... 14

Instructions on Correctly Setting the Baud Rate ......................................................................... 14

SettingtheInternalModulesBaudRate.................................................................................................15

Normal/Typical Start Sequence................................................................................................... 17

Internet Tab..................................................................................................................................... 18

Remote server............................................................................................................................. 18

Local Server................................................................................................................................ 18

Use Protocol................................................................................................................................ 18

Firewall........................................................................................................................................ 18

Transparency .............................................................................................................................. 18

ISP Dial up Login......................................................................................................................... 19

Page 3 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

Connect to ISP or Server ............................................................................................................ 20

Data Transfer Tab........................................................................................................................... 21

Setting the SWT Timers.............................................................................................................. 21

Functional Timing Description..................................................................................................... 22

Heart Beat package..................................................................................................................... 23

Ping Sending............................................................................................................................... 23

Analogue Values......................................................................................................................... 24

Server ............................................................................................................................................. 24

Terminal.......................................................................................................................................... 25

Entering command mode............................................................................................................ 25

Send – commands ...................................................................................................................... 25

Set RTC....................................................................................................................................... 25

Reprogram Using CSD................................................................................................................ 25

Main Init .......................................................................................................................................... 26

Default Mode............................................................................................................................... 26

Miscellaneous.............................................................................................................................. 26

Init AT-Command Table.............................................................................................................. 27

Low Power Sleep Mode (SWT5)................................................................................................. 27

ConsiderationswhenusingLowPowerSleepMode..............................................................................27

Active profile:............................................................................................................................... 29

Logging Tab.................................................................................................................................... 31

Data Logging............................................................................................................................... 31

Pulse Counting Transition........................................................................................................... 31

Channels to Log.......................................................................................................................... 31

Wakeup Timer 1 Settings (SWT1)............................................................................................... 31

Logging slots available................................................................................................................ 32

Logged Data................................................................................................................................ 32

Hardware Description ..................................................................................................................... 33

Power Supply.............................................................................................................................. 33

RJ45 I/O Connector..................................................................................................................... 33

I/O Connector pins ...................................................................................................................... 34

Serial (RS232) Port......................................................................................................................... 34

Antenna........................................................................................................................................... 34

SIM Card......................................................................................................................................... 35

SIMPin.....................................................................................................................................................35

Indicator Lights................................................................................................................................ 36

Low Power Mode (LPM) Example/Description ............................................................................... 37

Real time Clock and reference date................................................................................................ 39

Reference Date Description........................................................................................................ 39

Real Time Clock Description....................................................................................................... 39

I/O 7 Toggling ................................................................................................................................. 40

Calibration of Analogue Inputs........................................................................................................ 42

Equipment we need:.................................................................................................................... 42

Procedure:................................................................................................................................... 42

Querying/Programming the Modem Using ET Commands............................................................. 45

Page 4 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

Document

History

Revision Date Issued By Description

V001 30th April 2014 Patrick Paffard First Issue

Relevant Documents

The documents listed below are useful for the understanding of this document.

Document ID/No. Title

2005-0001 57 ETM Modems ET Communication Spec

2003-0003 16 ETM Modems TCP UDP Port Configuration Spec

2005-0001 17 ETM Modems TCP UDP Protocol Spec

ETM9140 9120 Quick Start

Guide 201405RV01 ETM9120 9140 Quick Start Guide

IO Board Brochure

201405RV01 IO Board Brochure

Abbreviation

Abbreviation Used Description

EEPROM Electrical Erasable Program Read Only Memory

UART Universal Asynchrony Receive Transmit

CR Carriage Return

LF Line Feed

CT Configuration Tool

MCU Microcontroller

RTC Real Time Clock

RD Reference Date

BPS Bits per second

WIRELESS MODEM ETM9120-1 OR ETM9140-1

GSM/GPRS/UMTS Wireless

Page 5 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

Introduction

This document describes the operation of two ETM modems and therefore within this document

both types of product are referred to with the generic term of ‘wireless modem’ and wherever there

is a distinction required between the two there a clearly identified header will be shown for each

type of product;

Overview.

The ETM9xxx-xxx range of products are industrial terminals designed for M2M (Machine to

Machine) communications. With 3G &/or 2G options they provide the ideal communication, alarm

or control platform for GSM, GPRS, UMTS or SMS applications.

Nomenclature

The ETM9120-1 variants incorporate the Cinterion TC63i engine and are intended for worldwide

use (network and regulatory approvals permitting).

The ETM9140-1 variants incorporate the Cinterion PH8-P and are intended for worldwide use

(network and regulatory approvals permitting).

Terminal Nomenclature/History

Model Comment Module Installed

ETM9120 Variants

ETM9120-1 First Release TC63i

ETM9140 Variants

ETM9140-1 First Release PH8-P

This document refers to GSM/GPRS by the generic term ‘wireless’ and so you should

remember that the ETM 9120-1 wireless modem cannot access UMTS/HSDPA services.

This document refers to GSM/GPRS/UMTS/HSDPA by the generic term ‘wireless’ and so you

should remember that the ETM 9140-1 wireless modem can access GSM/GPRS/UMTS

services.

The wireless modem is equipped with an EEPROM that is programmed with an application image

supporting the required operation and functions of the wireless modem.

The data configured within the EEPROM is for alarm messages, telephone numbers, port input

and output status, baud rate, id numbers and user passwords.

A configuration tool is used to read-write to the modem to program specific functionality, it is very

important to ensure the correct version of the tool is utilised when reading or writing to/from the

modem.

Using the Configuration tool

Installation

The Configuration Tool can be copied to any folder on a suitable PC’s hard drive. It consists of only

one file and does not need to be installed. Depending on your use of the tool there may (over a

period of time) be configuration files, with an etx extension, created and these files can be saved in

any location. The tool itself may create a single ini file which should be left in the same directory as

the configuration tool for continued easy operation of the tool.

Page 6 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

The wireless modem should be connected to the PC with a standard 9 pin serial (pc to modem)

cable – the wireless modem is configured as a DCE (Data Communication Equipment). New PC’s

and particularly laptops may need to utilise a USB-Serial converter to provide a serial port.

Initial Start-up and Programming

When the unit starts up and is connected to a terminal window and Escape is pressed (see below)

the version of the configuration tool will be shown as follows, check you have the correct

configuration tool for the unit – if you do not then contact ETM and request the appropriate version

or visit the support section of ETM’s website.

When you power up the wireless modem to do any configuration you MUST follow these steps if

you are unfamiliar with the operation of the Configuration Tool:

Start the configuration tool.

Chose the correct communications port ( using the Set COM Port button to select a port other

than the one chosen by the Configuration Tool ) – ensure the port is set for a baud rate of

115200 (it must be at this speed to be programmed in ESC mode).

Confirm that the port opens (the indicator MUST show ‘OPEN’ for your chosen port).

Click on the Terminal Tab.

Click into the black terminal window so that you see a flashing white cursor.

Power up the wireless modem - remember to plug the power into the correct socket, it is the

one next to the antenna lead, plugging the power connector into the I/O connector can

damage it, if this happens you may need to return the wireless modem for repair.

Immediately after powering up the modem press the ESC key on the keyboard, you should

only need to press it 3 or 4 times, after a short period you should see an ‘Escape Pressed’

message from the wireless modem – if you don’t and instead you see a ‘MS:^SYSSTART’

message then repeat the process again. Without the ‘Escape Pressed’ message being

displayed you CANNOT perform any configuration on the wireless modem (while it is possible

to use the Configuration Tool once the wireless modem has fully started up this may not be

possible if the wireless modem has not yet been fully configured).

NOTE: You can also check ‘Send <ESC> on SYSTEM START’ (the Configuration Tool to will

automatically send an ESC character when it sees the SYSTEM START message) in the

bottom right hand corner of the Configuration Tool (but this doesn’t work with some USB to

Serial adapters) – if you check this remember to uncheck it again when you restart the modem

after any programming changes, otherwise you may inadvertently leave the modem in

programming mode rather than run mode.

In this example the

appropriate

configuration tool is

CT0600

Caution

Do not try to program/configure a

unit with the wrong version of the

configuration tool.

Page 7 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

You are now ready to use the configuration tool to make changes to the wireless modem.

Once you are familiar with the Configuration Tool you can shorten the procedure, if the

wireless modem is already live/working, by simply reading and writing the configuration without

restarting the wireless modem and pressing the ESC key. Note if any changes are made to the

modem you should power cycle or software reset (ET&SR) the modem to ensure that any new

mode of operation ( based on your configuration changes ) comes into effect. If you make no

changes, only reading the configuration, you do not need to restart the modem.

Settings can be saved to a file on your PC. If you need to configure another ETM9XXX-XXX

with the same settings this file can be loaded into the configuration tool and written to any

additional units that require the same settings.

Saving, reading and writing configuration files

File (Menu Option)

Select “File – Open” to open an existing configuration file.

Select “File – Save” to save a configuration file after you have read an existing configuration

from a device or when you have manually entered a configuration.

The configuration tool’s current settings can be written to the wireless modem by selecting

“WRITE MEMORY” – this is the button with the RED text.

Note: You cannot perform a write operation if you have not opened an existing configuration

file or performed a read operation.

To read the current settings of the wireless modem select “READ MEMORY” – this is the

button with the BLUE text.

“ComPort <Open> or <Closed>” can be used to control whether or not the communications

port is opened (You must have the communications port open to connect in any way to the

wireless modem).

The Port Open/Close feature allows you to leave the configuration tool open but not connected to

the serial port in case you need to use another communications application such as

HyperTerminal.

The selected baud rate for the COM port is displayed in brackets when the port is opened.

Note: If the unit is busy a read or write may fail and a popup will inform you of the error, this is

usually because the unit is in normal/operational mode. You can retry the read or write but if it

continues to fails then put the unit into programming or ESC mode (see above).

Caution

Take care not to over-write a previously

configured unit with a default or other

incorrect configuration

We suggest reading back after making any

changes to confirm they have been

correctl

entered

Page 8 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

Alarm / Message Tab

The unit can send messages based on inputs to up to 5 mobile users.

SMS phone numbers and user ID

SMS Central is taken from the SIM-card and cannot be changed.

Number 1 – 5 lists the recipients of the alarm messages, i.e. +6141xyyyzzz

Note: It is our recommendation that you use the full international number in any entry.

Latest Incoming SMS

“Phone Number” shows the last number to send a valid message

“Date and Time” shows when the last valid message was received

Note: You can use these two entries to determine if there is a problem sending SMSs to the

wireless modem…. If you don’t see your SMS displayed it may be because your SMS is not

being delivered or because of an SMS formatting issue.

SMS formatting issues will affect you if you use a phone to send an SMS that has extra

characters inserted. As an example one type of phone will insert a variable line of dashes at

the top and bottom of an SMS and the wireless modem cannot then determine where, within

the SMS, the real content starts and so the SMS is rejected.

To diagnose whether or not the SMS has formatting issue you can send a test message from

your phone to another type of phone and see if there are extra characters OR call your

distributor and they may be able to give you a test number to send to and they could then let

you know whether the content and format of your messages is acceptable.

Unit ID added to messages

If you select “Use SIM Phone Book (Phone number 1) as User ID” the ID of the unit will be

whatever number is configured in that slot.

Note: This does not change the number from which any SMS is sent – it simply identifies the

device in the text area of any data sent.

If you select “Use SIM Card ID as User ID” the units ID will be the ID of the SIM.

See note above about the ID

Page 9 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

If you want to enter a textual ID then enter it into the text box and uncheck the two checkboxes

above

You have forty (40) characters available and we suggest that you use the shortest practical ID

possible as there are only 160 characters available in an SMS and if you use 40 characters for

the ID this leaves only 120 characters for the content of the SMS which may limit the

information that can be sent.

When entering a specific ID you should not use punctuation characters – to guarantee that you

don’t affect the field positioning of any data being sent by the 9900 you should never use a

comma in the Device ID. If you have a comma in the Device ID you will effectively add a new

field to any data sent as the data is delimited with commas by default.

Use incoming security filter

You may restrict the users that can access the unit, users sending SMSs to the 9900 to control

configurable options or to return current statuses by selecting “Use incoming SMS security

filter”

Maximum number of SMSs per day allowed to be sent

To prevent a large number of SMSs being sent due to an invalid configuration or an unstable

input/system state you may limit the maximum SMSs sent in a single 24 hour period. This 24

hour period starts at the time the wireless modem is powered and is not based on any specific

time.

See the Delay and Alarm Restore Delay description (within the individual I/Os) for other ways

to limit invalid sending.

If the wireless modem exceeds the maximum allowed SMSs in a single 24 hour period then

any alert that is triggered will still generate a message to the serial port (and will send a TCP

or UDP alert if configured) but no SMSs will be sent until the current 24 hour period expires.

There is no indication available of when the current 24 hour period expires.

Alarm Messages

Append Alarm status allows you to chose whether or not to add the status (High or Low) to the

alert message – by default you would normally enable this.

Append Unit ID allows you to choose whether or not to add the Unit Id to the alert message.

Page 10 of 46 For Support Contact +61-2-9956-7377

Or [email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

I/O Settings

7 x I/O’s configurable as digital, analogue or pulse are available on the RJ45 connector, pin

allocations are as shown below.

Pin Function Looking at Modem Socket

1 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Pulse Input: LL<0.5V, HL>2.5V, Max Input 50VDC

2 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Pulse Input (I/O8): LL<0.5V, HL>2.5V, Max Input 50VDC

3 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Pulse Input (I/O9): LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Analogue Input: 0-2.5VDC, Max Input 50VDC

4 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC, Max Input 50VDC

5 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC, Max Input 50VDC

6 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC, Max Input 50VDC

7 Configurable as:

◩ Digital Input: LL<0.5V, HL>2.5V, Max Input 50VDC

◩ Digital Output: LL0V, HL3V,0.1mA

◩ Analogue Input: 0-2.5VDC, Max Input 50VDC

IO7 can also be used as a „toggled“ output in combination with the ETM IO board

to provide switched sensor power supply – contact ETM for more details

8 GND

IO 1 & 2

Delay before alarm is activated

Is recommended to reduce the incidence of multiple SMS being sent in the event of

chattering/bouncing contacts

Caution

Take care to ensure that only

the correct connectors are

used or mechanical damage

to the pins may result.

12345678

Caution

SMS Alarm - Never tick a

blank number as this will

cause the modem to try to

repeatedly send an alarm to a

non-existent number

Ce manuel convient aux modèles suivants

Table des matières

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur