ETAS ES4105.2 Manuel utilisateur

ES4105.2 Housing

User’s Guide

ES4105.2 Housing2

The data in this document may not be altered or amended without special

notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in

relation to this document. The software described in it can only be used if the

customer is in possession of a general license agreement or single license.

Using and copying is only allowed in concurrence with the specifications stip-

ulated in the contract.

Under no circumstances may any part of this document be copied, repro-

duced, transmitted, stored in a retrieval system or translated into another lan-

guage without the express written permission of ETAS GmbH.

The names and designations used in this document are trademarks or brands

belonging to the respective owners.

R1.2.1 EN- 10.2003 TTNF00K103383

Contents 3

Contents

1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Display Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 Power Supply Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.5 Ventilation Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.6 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Installation of VMEbus Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Removal of VMEbus Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4 Automatic Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 VME64x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Battery Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Contents4

5Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Introduction 5

1Introduction

This section contains information about the basic features and applications of

the ES4105.2 Housing.

1.1 Features

The ES4105.2 Housing is a compact housing for VME boards. It has the follow-

ing features:

•10slots

• standard VMEbus and VME64x boards

• slots for standard Eurocards (100 mm x 160 mm) separated at 4 HP inter-

vals (22.3 mm)

• 160-pin backplane

• +3.3 V, +5 V, +12 V, and -12 V power supply

• power adapter with wide input voltage range

•fan

• Case with tip-up/carrying handle

• 4 U front panel height

• power switch and fault indications on the front panel

Introduction6

Functional Description 7

2 Functional Description

This section contains a detailed description of the features of the housing.

2.1 Display Elements

The front panel of the housing has four LEDs and a control lamp in the power

switch that show you various operating and error statuses.

2.2 Slots

The ES4105.2 Housing provides 10 slots at intervals of 4 HP. The slots are

designed for standard Eurocards in 100 mm x 160 mm size. The front panel

height of the plug-in boards measures 3 U.

2.3 Backplane

The backplane of the housing has 160 pins. The pin allocation complies with

the extended VMEbus standard VME64x. Both VME-standard boards and

extended VME64x-standard boards can be inserted.

2.4 Power Supply Unit

The power supply unit provides the voltages +3.3 V, +5 V, +12 V, and -12 V.

The power supply unit is designed as a wide range unit with an input voltage

range of 100 V to 260 V and a frequency range of 50 Hz to 60 Hz. Its maxi-

mum power is 180 W. All output voltages are protected against overcurrent.

2.5 Ventilation Fan

The housing is equipped with one fan.

2.6 Fuses

The mains voltage is protected with two fuses (3.15 A slow). The fuses are

integrated in the line connector (on the rear of the housing).

Display Significance

Power Switch Power supply switched on and power voltage applied.

+3.3 V The supply voltage +3.3 V is active.

+5 V The supply voltage +5 V is active.

+12 V The supply voltage +12 V is active.

-12 V The supply voltage -12 V is active.

Tab. 2 -1 Display on the Front Panel

Functional Description8

Operation 9

3 Operation

This section provides information about the installation and removal of the

VMEbus boards, fuse replacement, and automatic overcurrent protection of

the housing.

3.1 Installation of VMEbus Boards

Some VMEbus boards need to be configured before they can be installed. The

corresponding information can be found in the manuals of the VMEbus board.

To install a board:

1. Turn off the power to the housing. Check that all

devices connected with the housing by cables

have also been powered off.

2. If the slot in which you want to install the board

is protected by a cover, remove this cover.

3. Insert the board into the slot. Make sure that the

top and bottom of the board smoothly slide in

the guide rails.

4. Push the board in until the connector securely

locks into place.

5. Fasten the mounting screws for the front panel

of the board.

6. Connect the required cables with the front panel

connectors.

3.2 Removal of VMEbus Boards

To remove a board:

1. Turn off the power to the housing. Check that all

devices connected with the housing by cables

have also been powered off.

note

The boards may only be configured and installed at a workplace that is protected

against electrostatic discharges.

note

The boards may only be removed at a workplace that is protected against elec-

trostatic discharges.

Operation10

2. Disconnect all connectors from the board you

want to remove.

3. Loosen the mounting screws at the top and bot-

tom edge of the board’s front panel.

4. Grasp the handle of the board and pull the board

carefully out.

5. Insert the board into its storage package or an

anti-static bag.

6. Secure the slot with a protective cover.

3.3 Fuse Replacement

The power supply line of the built-in AC unit is protected by two 3.15 A fuses.

Both the neutral wire and the phase wire have their own fuse.

To replace the fuses for the built-in AC unit:

1. Turn off the power to the housing. Check that all

devices connected with the housing by cables

have also been powered off.

2. Disconnect the power cable of the housing from

the rubber socket.

3. Unlock the fuse holder (in the mains connector)

with a screw-driver.

4. Replace the defective fuse with a new fuse rated

3.15 A (slow), 250V.

5. Reinsert the fuse holder.

6. Reconnect the power cable.

3.4 Automatic Overcurrent Protection

The built-in AC unit of the housing is equipped with an automatic overcurrent

protection. If the AC unit detects an overcurrent condition for an output volt-

age, it shuts down all outputs. The corresponding front panel LED goes dark.

The AC unit’s overcurrent protection can be reset by briefly powering it off.

To reset the automatic overcurrent protection:

1. Turn off the power to the housing.

2. Wait approximately one minute.

Table des matières

Autres manuels ETAS Matériel informatique

ETAS

ETAS ETK-S6.0 Manuel utilisateur

ETAS

ETAS ES1231.2-A Manuel utilisateur

ETAS

ETAS XETK-S21.0B Manuel utilisateur

ETAS

ETAS XETK-S31.0 Manuel utilisateur

ETAS

ETAS XETK-S21.0 Manuel utilisateur

ETAS

ETAS BR XETK-S4.0 Manuel utilisateur

ETAS

ETAS BR-XETK-S4.0 Manuel utilisateur

ETAS

ETAS BR XETK-S3.0 Manuel utilisateur

ETAS

ETAS ETK-S21.1 Manuel utilisateur

ETAS

ETAS FETK-T1.1 Manuel utilisateur

ETAS

ETAS FETK-T4.0B Manuel utilisateur

ETAS

ETAS ES4455.1 Manuel utilisateur

ETAS

ETAS BR XETK-S2.0 Manuel utilisateur

ETAS

ETAS ES4602 Manuel utilisateur

ETAS

ETAS BR_XETK-S3.0 Manuel utilisateur

ETAS

ETAS XETK-S23.0 Manuel utilisateur

ETAS

ETAS ES5352.1 Manuel utilisateur

ETAS

ETAS XETK-S22.0 Manuel utilisateur

ETAS

ETAS MDA V8.6 Manuel utilisateur

ETAS

ETAS ES1392.1 Manuel utilisateur

ETAS

ETAS ES5340.2 Manuel utilisateur

ETAS

ETAS XETK-S22.0 Manuel utilisateur

ETAS

ETAS XETK-S4.2 Manuel utilisateur

ETAS

ETAS FETK-S2.1 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur