Ericsson E1 Manuel utilisateur

Quick start guide

What's included

E1 by Ericsson

Gateway Router

Ethernet cablePower adapter

Hardware speciﬁcations:

• 802.11AX tri-band router capable of 6000 Mbps theoretical maximum throughput

• WAN broadband RJ-45 input

• Two (2) LAN Ethernet RJ-45 ports

Light arc

WPS

Reset

SD/SIM

LANLAN WAN

Lorem Ipsum dolore sit

Consectetur adipiscing elit 23456

S/N: DU00001234

Duis aute irure dolor

Excepteur sint occaecat

Lorem Ipsum dolore sit

Consectetur adipiscing elit

Duis aute irure dolor 12345

Lorem ipsum dolor sit amet, consectetur

adipiscing elit, sed do eiusmod tempor

incididunt ut labore et dolore magna aliqua. Ut

enim ad minim veniam, quis nostru exercitation.

1Install the included nano-SIM card,

or plug in the Ethernet cable into the

E1 Gateway Router’s WAN port.

To install the nano-SIM card: Use a Phillips head screwdriver to unscrew the SIM card slot

cover. Insert the nano-SIM card with chip facing up, until it gently clicks into place. Screw the

SIM card slot cover back on.

Bottom

Top

WPS

Reset

SD/SIM

LANLAN WAN

Lorem Ipsum dolore sit

Consectetur adipiscing elit 23456

S/N: DU00001234

Duis aute irure dolor

Excepteur sint occaecat

Lorem Ipsum dolore sit

Consectetur adipiscing elit

Duis aute irure dolor 12345

Lorem ipsum dolor sit amet, consectetur

adipiscing elit, sed do eiusmod tempor

incididunt ut labore et dolore magna aliqua. Ut

enim ad minim veniam, quis nostru exercitation.

Plug into wall outlet

Connect power cable to power port

Plug the power adapter into a power outlet, and plug the other end into the power port on the

underside of the router. The router is ready to use when the light arc stops ﬂashing and blue

light begins pulsing on and off.

2Connect the power supply

3Select a Wi-Fi network

The default SSID’s (network names) are:

Ericsson_[last 4 digits of serial number]_2.4G

Ericsson_[last 4 digits of serial number]_5G_1

Ericsson_[last 4 digits of serial number]_5G_2

The default password for all networks is:

ericssonxxxx

xxxx = Last four digits of the E1 Gateway Router’s serial number. (e.g. ericsson1234)

Note: The serial number is

printed on the bottom of the

E1 Gateway Router.

WPS

Reset

SD/SIM

LANLAN WAN

Lorem Ipsum dolore sit

Consectetur adipiscing elit 23456

S/N: DU00001234

Duis aute irure dolor

Excepteur sint occaecat

Lorem Ipsum dolore sit

Consectetur adipiscing elit

Duis aute irure dolor 12345

Lorem ipsum dolor sit amet, consectetur

adipiscing elit, sed do eiusmod tempor

incididunt ut labore et dolore magna aliqua. Ut

enim ad minim veniam, quis nostru exercitation.

S/N: DU00001234

Advanced router settings

To improve the security of your wireless networks, consider changing the SSID’s and

passwords to something different than the default. This can be done through advanced

router settings.

To access advanced router settings:

1. Connect an Ethernet cable from the LAN port on the E1 Gateway Router to your computer,

or connect to the E1 Gateway Router via WiFi SSID.

WPS

Reset

SD/SIM

LANLAN WAN

LoremIpsum dolore si t

Consecteturadipiscing elit 23456

S/N:DU00001234

Duisaute irure dolor

Excepteursint occaecat

LoremIpsum dolore si t

Consecteturadipiscing elit

Duisaute irure dolor 12345

Loremipsum dolor sit amet, consectetur

adipiscingelit, sed do eiusmod tempor

incididuntut labore et dolore magna aliqua. Ut

enimad minim veniam, quis nostru exercitation.

Ethernet cable

Computer

*Advanced router settings (cont’d)

2. Open an internet browser window, type in the IP address: 192.168.1.1, and complete the

search by pressing Enter or Return on your keyboard. Alternatively, you can search for:

http://E[router-serial-number] (i.e. http://EDU00001234/ )

3. Log in using the default username and password:

Default username: root

Default password: ericssonxxxx

xxxx = Last four digits of the E1 Gateway Router’s serial number. (e.g. ericsson1234)

*Expert users

Advanced router settings may also be accessed via SSH console.

1. Connect an Ethernet cable from the LAN port on the E1 Gateway Router to your computer,

or connect to the E1 Gateway Router via WiFi SSID.

2. Open a PowerShell or Command Prompt with admin privileges.

3. Type: ssh [email protected]

4. Log into advanced router settings:

Default password: ericssonxxxx

xxxx = Last four digits of the E1 Gateway Router’s serial number. (e.g. ericsson1234)

Tip: You can check the cellular module status using AT Commands or with the preinstalled

macro by typing: lte-info or lte-atcmd AT!GSTATUS?

Frequently asked questions

How do I change the Wi-Fi SSID (network name) and password?

1. Log into advanced router settings, choose Network from the list on the left, and then click

Wiﬁ from the list that appears under Network.

2. Find the network you want to edit, and click EDIT.

3. To change the network name, look for the Interface Conﬁ guration section. There, under the

General Setup tab, you will see a space labeled SSID where you can type in a new network name of

your choosing.

4. To change the password, click the Wireless Security tab. There you will see a space labeled Key

where you can type in a new password of your choosing. (Be sure to write it down in case you forget

it later.)

5. Click SAVE AND APPLY when  nished.

How do I conﬁ gure LTE/5G?

Log into advanced router settings, choose Network from the list on the left, then click LTE Conﬁ gura-

tion. Here you can con rm the SIM, APN, and IMEI are correct.

How do I access LTE/5G information?

1. Log into advanced router settings, choose Network from the list on the left, then click Diagnostics.

2. In the section labeled LTE Information, click the CHECK button and wait a few seconds for

the web page to display. Here you can  nd the internal connectivity status, band information, BW,

CA, and more.

Status LED display

Booting Seven colors cycle the light arc.

Networking connecting Green light blinks three times.

System ready Blue light pulses on and off.

Networking change Yellow light spreads from the center to the edge.

WPS One by one, each LED turns blue and blinks.

WPS success Green light blinks ve times.

WPS fail Orange light blinks ve times.

Firmware upgrade LED’s display an incrementing progress bar pattern.

Loss or no internet connection Red light arc pulses on and off.

What do the lights on the E1 Gateway Router mean?

The E1 Gateway Router communicates its status using different LED displays.

How do I check LTE/5G network connectivity and signal strength?

Log into advanced router settings, choose Network from the list on the left, then click Interface.

Here you can conrm the WWAN network connectivity is active along with SIM status and signal

strength (RSSI).

There are two ways to reset the E1 Gateway Router to factory settings.

Hardware method

Press and hold the Reset button located on the base of the router for ten seconds.

WPS

Reset

SD/SIM

LANLAN WAN

Lorem Ipsum dolore sit

Consectetur adipiscing elit 23456

S/N: DU00001234

Duis aute irure dolor

Excepteur sint occaecat

Lorem Ipsum dolore sit

Consectetur adipiscing elit

Duis aute irure dolor 12345

Lorem ipsum dolor sit amet, consectetur

adipiscing elit, sed do eiusmod tempor

incididunt ut labore et dolore magna aliqua. Ut

enim ad minim veniam, quis nostru exercitation.

Reset

Reset to factory settings

Interface method

1. Log into advanced router settings, choose System from the list on the left, then click Reboot/Reset.

2. Select PERFORM FACTORY RESET.

The router will reset to factory default settings and reboot automatically. The process takes about

two minutes.

Note: Power must be kept on during the full reboot sequence.

Check with E1 Customer Support to get a link to a validated router  rmware image. Download the

 rmware image and then upload it to advanced router settings.

To upload:

1. Log into advanced router settings, choose System from the list on the left, then click

Backup/Flash Firmware.

2. In the Flash New Firmware Image section, click Choose File and select the  rmware image.

4. Click FLASH IMAGE.

5. Click PROCEED to ﬂ ash. (This may take around two minutes.)

6. Once complete, log into advanced router settings again, click Status, and select Overview to check

the  rmware version.

Note: To ensure the router and SIM data are properly updated:

1. Turn OFF the E1 Gateway Router and unplug power for 10 seconds.

2. Plug power back in and turn ON the E1 Gateway Router for a fresh boot.

1 2

Update ﬁ rmwareReset to factory settings (cont’d)

Autres manuels pour E1

Table des matières

Autres manuels Ericsson Porte

Ericsson

Ericsson EDACS Jessica Manuel utilisateur

Ericsson

Ericsson RBS 2308 Manuel utilisateur

Ericsson

Ericsson EDACS Jessica Manuel utilisateur

Ericsson

Ericsson EXN401 Manuel utilisateur

Ericsson

Ericsson HM410dp Manuel utilisateur

Ericsson

Ericsson HM490dp Manuel utilisateur

Ericsson

Ericsson EDACS Series Mode d’emploi

Ericsson

Ericsson HM410dp Manuel utilisateur

Ericsson

Ericsson LBI-39001 Manuel utilisateur

Ericsson

Ericsson EDACS Data Advantage Series Mode d’emploi

Ericsson

Ericsson 5780 Manuel

Ericsson

Ericsson MD110 Feuille d'instructions

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur