Epson Stylus D88 Manuel utilisateur

Tel: 01332 855 085

Fax: 01332 855 080

Technical Support: 01332 858 333

Instruction Manual

Subli-Print

Epson D88

V2.0 July 2007

CONTENTS

Page 16

Section 1

Section 2

Driver Installation & Setup

CorelDRAW setup

Section 10 Troubleshooting

General troubleshooting and tips

Page 1 Installing & setting up the Epson D88 Printer

Section 3 Printing

Page 2-3 Installing & setting up the Xpres Subli-Print colour profile

Page 3 Printing with the Xpres Subli-Print colour profile

Section 4 Bulk feed system

Page 4-10 Installing the Subli-Print bulk feed system

Section 5 Templates

Page 11-12 Working with CorelDRAW sublimation templates

Page 12 Tips on using templates

Page 12 Tips on using Subli-Print ink

Section 6 Sublimation ink

Section 7 Sublimation paper

Page 12 Sublimation paper usage and tips

Section 8 CorelDRAW

Page 13 Introducing CorelDRAW and its tools

Page 14 CorelDRAW's most common tools

Page 14-15 Common CorelDRAW tasks

Page 15 Sublimation printable's hints and tips

Section 9 Printable's

Diagram 1 Diagram 2

Diagram 5

Diagram 4

Diagram 3

Diagram 6 Diagram 7 Diagram 8

Diagram 9 Diagram 10 Diagram 11

Click

Advanced

Name it

Subli-print

Click 'Save' then click

OK until all open boxes

are closed.

Installing & Setting up the Epson D88 printer

Insert the Epson Stylus D88 software CD-ROM into your CD-ROM drive. The CD will auto run. Select 'Custom

Install' from the menu, as in diagram 1below. When Diagram 2appears click 'Printer Driver'. It will display diagram

3, click OK and it will copy files to your computer. Make sure the USB cable is connected to the PC and printer, then

turn on the printer as instructed in diagram 4. After the utility has found your printer it will confirm this as in diagram 5.

The Epson D88 has now been successfully installed. Click OK.

Now follow the Epson D88 driver setup below.

Browse to the Printers and Faxes folder. Right click on the Epson D88 printer and click on 'Properties'. Click on

'Printing preferences as in diagram 6, then follow the diagrams below.

Click

Save Setting

Click

Mirror Image

. Epson Matte

. Photo

. ICM

. Off (No Color Adjustment)

After installation

The Epson Status Monitor

needs disabling before

use. Follow the below

steps.

1. Go to the printers and

faxes folder.

2. Right click on the D88

and select properties.

3. Click printing

preferences.

4. Click the Maintenance

tab.

5. Click on the 'Speed &

Progress' button.

6. Un-tick 'Show Progress

Meter'.

7. Un-tick 'Disable EPSON

status monitor 3'.

8. Click OK three times

to close the driver boxes

down.

Setting up CorelDRAW 10 onwards

Diagram 2

Before you start this section you will need to download the Xpres Subli-Print colour profile from the Xpres website.

The address is

www.xpres.co.uk/technical.php You can also find the profile on the Subli-Print CD supplied with the bulk

feed system. This disk can also be sent out upon request.

Close CorelDRAW. When you have downloaded the 'Subli_Print_D88_V1.icm' colour profile, right click on it and

choose 'Install Profile' from the top of the menu. Note: The profile will install automatically and will not give any feedback.

Also on some systems you will not be able to see the 'Install Profile' option. If this is the case change the .ICM extension

to .ICC then re-try.

Start CorelDRAW and click on Window > Colour Palettes. Tick the 'Default RGB palette'. Repeat the process then

un-tick 'Default CMYK palette'. Now click on Tools > Colour Management. You will now see the colour management

dialogue box appear as in diagram 1below.

Note: For CorelDRAW X3 users

click on 'RGB (used in versions

previous to CorelDRAW X3', under

the 'Colour mode used for effects'

section at the bottom.

First, all the (Orange/Grey) arrows need to be set as shown above. To change the colour of the

arrows (Orange colour switched on, Gray colour switched off). To turn the arrows on or off just click

on the arrow itself.

Configure Import-Export Settings: Click on the image of the paper to bring up the window shown

below (diagram 2). This window configures how CorelDRAW handles files that are imported to a

document.

Composite Printer: Select the Subli_Print_D88_V1 printer profile. Note: if you cant choose the

Subli_Print_D88_V1 from the drop down menu means the ICC profile is not yet installed on your

pc or you may not have restarted Corel since the ICC installation. Close and re-launch Corel.

Click Import: Always covert Using- Select Internal RGB Fraser

(1998) from the drop down menu.

Click Export: Always embed using- Select Internal RGB Fraser

(1998) from the drop down menu.

Click OK.

Diagram 1

Monitor: Select the ICC profile for your monitor (If you also have Adobe Photoshop on your system

you can select the profile you created in Adobe Gamma). You may also check out the website of your

monitor manufacturer for ICC profiles for your particular monitor. If you do not have an ICC colour

profile use the 'Generic Profile' instead.

Internal RGB Space: Select Internal RGB Fraser (1998)

Save your settings: Click the + button and name your settings Subli-Print then Click OK.

CorelDRAW's colour management is now setup. You can now work with your images as normal.

When you have your image ready on screen, click file > print. You will now see the print dialogue

box below (diagram 1).

The Epson D88 properties will now show (diagram 2). Ensure the Subli-Print setting is highlighted.

If it is not click on 'Subli-Print' from the drop down list. Then click OK.

Now click on the Misc tab (diagram 3) and ensure the Subli_Print_D88_V1 is ticked.

Note: Ensure the 'Apply ICC profile' is un-ticked when using other printers.

Now click the print button.

Printing with the Subli-Print ICC profile

Diagram 1

Diagram 2 Diagram 3

D88

ITINERY

1. Bottles and cartridge assembly (pre-filled and including 2 small

clamps for fitting to printer housing).

2. 10ml Syringe

3. Small needle (only required for re-priming, see page 7)

4. Large extension

5. 4 x air filters

6. Subli-Print CD (including colour correction profile and instructions)

4 5

D88 Bulk Feed

Instructions

Turn on the printer and press the ‘ink’

button. When the printhead has moved to

the cartridge removal position unplug the

mains cable from the printer.

This allows the printhead to be manually

moved.

Remove any cartridges from the machine.

Remove all the small bungs from the bot-

tles. (do not throw these away as you will

need these for re-filling the bottles)

Using the long needle attachment on the

10 ml syringe draw any ink out of the

centre chamber (through the small hole).

Repeat this on each colour then fit the air

filters supplied.

Place the bottles to the left of the printer

as shown.

NEVER PLACE THE BOTTLES

HIGHER THAN THIS

(If the bottles are placed higher then the

ink may siphon into the bottom of the

printer.)

Make sure there are no twists in the

tubing.

Feed the cartridges through the opening in

the printhead lid. (If you have previously

removed this lid already do not worry as it

is not necessary for the operation of the

system).

Push the cartridges down firmly until they

snap into position. Close the printhead lid

making sure not to trap the tubing.

Remove the tape from the sticky pad and

firmly press the tube support into place as

shown Make sure the tubing is not

twisted..

Plug the printer back into the mains

supply and the printhead will move back

and forth then perform it’s initial ink

charge.

Remove the backing tape from the black

clamp on the tubes and fit it to the printer

housing as shown.

During this ink charge you should see the

ink flowing through the tubes near the

connectors.

The air you may see in the tubes is not signifi-

cant and will not affect the operation of the

system in any way.

After the ink charge print out a nozzle check to see if all the colours are printing

correctly. If they are, you are set to go. If not perform a head clean and test the

nozzle check again. You should see an improvement on the next nozzle check.

If still not perfect you can perform one or two more head cleans (do not overdo

this exercise) until you get a good nozzle check.

Occasionally a printer will stubbornly refuse to print a perfect nozzle check af-

ter a couple of head cleans. There can be a number of reasons for this including

the fitting of a dye sublimation system for the first time or a printer being left

for a long time without running any prints.

One way of curing this is to force the printer into a ‘power clean’. To do this

you will need to send a good size image to the printer (use an 8” x 10” [20cm x

25cm]) and when about a quarter of the image has printed, press (and hold

down) the ink button on your printer (Shown on page 2).

After you have held this button down for 5 or more seconds the printer will

pause printing (eject the paper), perform a head clean and then carry on printing

where it left off (it is not necessary to waste transfer paper on this exercise).

You may have to hold this button down again 1-2 more times during the print –

you should be able to see if the banding is disappearing. If you have had to

press the button for the 3rd time the printer will now perform a ‘power clean’.

Print a nozzle check immediately after this. If this nozzle check is good, you are

set to go. If there are still problems with it leave the printer to settle for at least

half an hour before printing out another nozzle check.

If there has still been no improvement you can carry out this ‘power clean’ ex-

ercise one more time including the half an hour settling time afterwards.

Autres manuels pour Stylus D88

Table des matières

Autres manuels Epson Imprimante

Epson

Epson Epson Stylus Photo P50 Series Mode d’emploi

Epson

Epson 4000 - Stylus Pro Color Inkjet Printer Mode d’emploi

Epson

Epson Stylus Photo895 Manuel utilisateur

Epson

Epson R1800 - Stylus Photo Color Inkjet Printer Manuel utilisateur

Epson

Epson TM-P60II Manuel d'utilisation et d'entretien

Epson

Epson SureColor SC-P8500E Series Manuel utilisateur

Epson

Epson ColorPage EPL-C8000 Manuel utilisateur

Epson

Epson R300 - Stylus Photo Color Inkjet Printer Dimensions

Epson

Epson SureColor F571 Manuel utilisateur

Epson

Epson TM-S2000 Series Manuel d'utilisation et d'entretien

Epson

Epson L455 Mode d’emploi

Epson

Epson A381H Guide de configuration

Epson

Epson DFX-5000+ Manuel utilisateur

Epson

Epson SureColor SC-F6400H Guide de configuration

Epson

Epson Aculaser 2600 Series Manuel utilisateur

Epson

Epson SC-B9000 Series Manuel utilisateur

Epson

Epson ET-2850 Series Manuel utilisateur

Epson

Epson SX410 Mode d’emploi

Epson

Epson TM U295 - B/W Dot-matrix Printer Manuel utilisateur

Epson

Epson LX-300+ Manuel utilisateur

Epson

Epson Stylus COLOR 3000 Manuel utilisateur

Epson

Epson Stylus Pro 7000 Series Manuel utilisateur

Epson

Epson Stylus Photo PX660 Mode d’emploi

Epson

Epson U925 - TM B/W Dot-matrix Printer Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur