Epson EPL-6000 Dimensions
EPSON
EPSON AMERICA, INC.
Product Support Bulletin
Subject:
Laser & Non-Impact Printer Error Codes
Date: 4/3/91
PSB No: P-0077
Page(s): 1 of 11
Originator: JV
Epson printers issue beep tones and/or displays error codes when certain error
conditions exist. Those beeps or codes can assist you in locating and repairing
customer’s printers. The following error codes are listed by product name.
EPl-4000 Display Codes
PE
Co
IL
IE
PJ
El
E2
E4
(blinking)
(blinking)
(blinking)
E6
*-)
YY (blinking)
E7
*--)
YY (blinking)
E8
-
YY (blinking)
E9 (blinking)
E0 (blinking)
bF
Paper End (out) detected
Cover open
Ink low
Ink End (out)
Paper jam
Heater error (broken heater wire)
Contact error (heater fan or thermistor contact)
CO34 DVR board error
CO34 Main board software Error I
(YY will be a number from 66(H) to 7D(H))
CO34 Main board software Error II
(YY will be a number from 02(H) to XB(H))
Board contact error, CO34 Main board hardware
(YY will be one of the following numbers: 80,81,84,85,
86,87,8A, 8C)
CO34 Main board hardware error
Abnormal voltage
Buffer overflow for fonts
PSB No: P-0077
Page: 2 of 11
EPl-4000 cont.
bo
Buffer overflow for graphics
CE
Card error
PS
Paper size error
Lr Release lever error
LE
Envelope lever error
dP
Data processing
FF
Depress the Form Feed button
EPL=6000/ActionLaser/ActionLaser+ LCD Codes
CHANGE DRUM
The drum needs to be changed. The drum cartridge may
not be installed, the cartridge may not be installed
properly or the cartridge may be defective.
COVER OPEN
Printer cover is open
CPU ERROR
Printer’s CPU has made a calculation error
ERROR 10
Program ROM error
ERROR 11
Font cartridge or identity cartridge checksum error
ERROR 12 RAM error
ERROR 20
Memory overflow
ERROR 21
Print overrun error
ERROR 22
Receive
buffer overflow
ERROR 30
Memory error
ERROR 31
Scanner error
ERROR 32
Heater (Heat Roller Unit) error
PSB No: P-0077
Page: 3 of 11
EPL-6000 cont.
ERROR 33
ERROR 40
FONT CARD ERROR
INSERTION ERROR
PAPER EMPTY
PAPER JAM
PAPER SIZE ERROR
PS CHANGE
Thermistor error
Parity / Framing error
Font cartridge is bad (or is not inserted) correctly
Paper is not inserted correctly or has jammed at the paper
tray
No paper in the paper cassette
Paper cassette is not installed properly
Paper cassette lid is open
Paper sensor is bad
Paper is jammed inside the printer
Paper setting does not match the size of the paper in the
paper cassette
Paper size requested by the host conflicts with the
SelecType setting
EPL-7000 LCD Codes
NOTE:
In some
cases, the
red
CONTINUE
light flashes when an error
is
detected.
This requires you to correct the problem and then press the CONTINUE
button to dear the error.
However, if the
AUTO
CONT option in SelecType is
set to ON, some errors may clear automatically even though the problem
remains.
Status messages are preceded by [S], warning messages are preceded by
[W], and error messages are preceded by [E]. In some cases the message
you see on your display also shows the printer mode.
[E] ADD MEMORY FOR CH-X
The printer has insufficient memory available in the channel displayed.
[E] CARD MEMORY OVERFLOW
This message indicates that the combined memory requirement of the cards in
slots A and B exceeds 4 Mbytes.
PSB No: P-0077
Page:
4
of 11
EPL-7000 cont.
[S] COPY END X/X
Multiple-copy printing is cancelled (you pressed the COPY END button when
the printer was off line).
[E] COVER OPEN
The printer cover is open or the imaging cartridge is not installed.
[S] DATA
The printer has received data but is not yet printing, or the printer has received
data and is off line.
[E] FEED JAM
Paper is not feeding into the printer from the specified cassette or has jammed
on its way into the printer.
[S] GRAPHIC DRAWING
Graphics are being created.
[E] ILLEGAL CARD
A card or cartridge in a particular slot cannot be read.
[S] INlTlALlZE
The printer is being initialized (reset) to the factory settings.
[E] INSUFF. MEMORY
The printer has insufficient memory available for the task you have given it.
This error can also be cleared by turning the printer off and back on again.
However, it may be necessary to simplify the page you are trying to print or
add more memory to the printer.
[E] PAGE BUFFER FULL
Text or graphics data has filled the printer’s buffer and an incomplete page is
ejected.
[S] PAPER FEEDING
The printer is feeding paper.
[E] PAPER JAM
Paper is not being fed into the printer or paper is jammed inside the paper
path.
PSB No: P-0077
Page: 5 of 11
EPL-7000 cont.
[E] PAPER OUT
There is no paper in the standard paper cassette and the optional lower paper
cassette (ii installed). Or, the paper set lever is in the manual position and you
are not feeding pages correctly.
[E] PAPER OUT SET AUTO XXX
There is no paper in any of the paper cassettes. The right column of the
display prompts you to load the correct paper size into the paper cassette.
[E] PAPER OUT SET OPT XXX
There is no paper in the optional lower paper cassette. The right column of
the display prompts you to load the correct paper size into the paper tray of
the lower paper cassette.
[E] PAPER OUT SET STD XXX
There is no paper in the standard paper cassette. The right column of the
display prompts you to load the correct paper size into the standard paper
cassette.
[E] PAPER SIZE ERROR
The paper size you selected with SelecType (or the default size if you have not
selected a size) does not match the paper loaded in the selected paper
cassette.
[S] PRINTING
The printer has received data and is printing.. . . .
[S] PRINT STOP X/X
The printer stops printing during a multi-copy print operation.
[S] RAM Check X.X MB
The printer is checking RAM (X.X = capacity).
[S] READY
The printer is ready to print.
[E] REINSERT CARD
lf this message appears on the display, you may have removed a font card or
cartridge while the FEED light was still lit or while the printer was on line.
PSB No: P-0077
Page: 6 of 11
EPL-7000 cont.
[E] REMOVE CARD
You may have inserted a font card or cartridge while the printer was on line or
while the FEED light was on. Data still remains in the printer’s buffer.
[E] RESELECT TRAY
The optional lower paper cassette is not installed and the INPUT option is set
to OPT or AUTO.
[S] RESET
The printer is being reset to the previous settings in the macro specified with
LOAD MACRO option in SelecType Level 1.
[S] ROM Check
The printer is checking ROM.
[E] SAVE MEMORY OVERFLOW
lf this message appears when you are trying to save a macro with the SAVE
MACRO option in SelecType Level 1, the printer does not have enough
memory to save any additional macros
[E] SERVICE REQ. CXXX
A controller error has been detected.
[E] SERVICE REQ. EOOXX
A print engine error has been detected.
XX=
03 Fusing Unit (low temp)
04 Main Drive Motor
05 Ozone Fan motor
06 Polygon Mirror Drive
09 HSync Signal
[E] SET FULL PRINT
This message may appear when you are trying to print graphics or a mix of
text and graphics.
[S] STANDBY MODE
When both CH P and CH S remain off for about thirty minutes, the printer
enters standby mode and this message appears.
[E] STARTUP ERROR
lf this message appears when you turn on the printer, the power may have
been turned off while the printer was performing a save or reset operation.
PSB No: P-0077
Page: 7 of 11
EPL-7000 cont.
[W] TONER LOW
The printer is almost out of toner. When this message first appears on the
LCD display, you can print up to 25 more pages.
[E] TONER OUT
The imaging cartridge must be replaced.
[E] TRAY SET AUTO XXX
The paper size setting does not match the paper loaded in the specified paper
cassette. The right column is the expected paper size and the currently
selected cassette.
[E] TRAY SET OPT XXX
The paper size setting does not match the paper loaded in the optional lower
paper cassette. The right column is the expected paper size.
[E] TRAY SET STD XXX
The paper size setting does not match the paper loaded in the standard paper
cassette. The right column is the expected paper size.
[S] WAlT
Printer is being reset after a START UP ERROR.
[S] WARMING UP
Printer is warming up.
EPL-7500
[E] COVER OPEN
Cover is open or the imaging cartridge is not installed.
[E] MANUAL FEED
Manual feed method is selected.
[S] OFF LINE
Printer is Off tine
[E] OUT OF PAPER
No paper cassette is installed, the paper cassette is empty, or the paper set
lever is in the manual position.
PSB No: P-0077
Page: 8 of 11
EPL-7500 cont.
[E] PAPER ENTRY JAM
Paper is not feeding from the specified paper cassette or has jammed on its
way into the printer.
[E] PAPER EXIT JAM
Paper is jammed inside the paper path.
[S] PRlNTlNG
The printer has received data and is printing.
[S] PRlNTlNG TEST
The printer is printing the test page.
[S] PROCESSING
The printer is processing data.
[S] QUlT THE JOB
The On-Line button has been pressed while a print job was in progress. The
job can be flushed by pressing the Reset button, or a reset can be cancelled
by pressing any other button.
[S] QUITTING THE JOB
The printer is flushing a job from the buffer.
[S] READY
The printer is ready to receive data.
[S] RESETTING
This message appears initially when the printer is turned on, and momentarily
between print jobs.
[E] TONER LOW
The imaging cartridge must be replaced.
[S] WAIT- FOR READY
The On-tine button was pressed while a print job was in progress. The printer
continues printing until the current job is completed, then it goes Of-Line.
[S] WAITING
The printer is in the process of executing a job and has run out of data and is
waiting for the channel to provide more data.
PSB No: P-0077
Page: 9 of 11
EPL-7000 cont.
[S] WARMING UP
The printer is warming up.
Note:
lf any of the following messages appear, turn the printer off for at least five
seconds, then turn it back on. lf the same message is displayed, repair is
required.
SCAN MOTOR ERROR
HSYNC ERROR
HEATER LAMP ERROR
MAIN MOTOR ERROR
FAN MOTOR ERROR
ES300C Display Codes
E-C
Command error. An unidentified command or parameter was detected.
E-l Interface error
a. Incorrect communication parameter received.
b. Broken connector or wire.
c. Host failed to respond within 30 seconds.
d. Host is not accepting data. (DSR= Low)
E-F Fatal error
a. A lamp is broken.
b. Power is applied before the transportation screws were removed.
c. System failure
GQ-3500 Display Codes
do
Cover Open error
EO-00
Engine driver CPU error.
EO-01
Option tray CPU error.
EO4+02
Option tray motor error.
PSB No: P-0077
Page: 10 of 11
GQ-3500 cont.
EO*03
EOo05
EOoo6
E1
-80
E1
*
81
E1
-82
E1
083
E1
084
E1
-89
E1
.+ 91
E1
-92
E1
-Al
E1
*A2
E1
*A3
J0
J1
J2
Po
PU
To
Optical unit error.
Main motor error.
Fusing unit error.
Exception error.
Trap error.
Bus error.
Address error.
Illegal Instruction.
NMI error.
Reverse vector interrupt error.
User vector interrupt error.
System RAM error.
External RAM error.
CG ROM error.
Paper feed error.
Paper feed jam.
Paper exit jam.
Paper empty, paper tray is not installed or paper is not
installed properly.
Paper size error.
Toner empty.
Autres manuels pour EPL-6000
2
Ce manuel convient aux modèles suivants
24
Autres manuels Epson Imprimante
Epson
Epson Perfection 1260 Photo Manuel utilisateur
Epson
Epson Stylus Pro 7000 Series Manuel utilisateur
Epson
Epson PowerRIP Stylus Manuel utilisateur
Epson
Epson Mobilink TM-P60 Manuel d'utilisation et d'entretien
Epson
Epson TM-C3500 Series Manuel utilisateur
Epson
Epson PP-100II Manuel utilisateur
Epson
Epson L110 Manuel utilisateur
Epson
Epson DLQ-3500 Manuel utilisateur
Epson
Epson SC-P800 Series Mode d’emploi
Epson
Epson M1120 Manuel utilisateur
Epson
Epson FX-880 - Impact Printer Manuel utilisateur
Epson
Epson Stylus COLOR 1160 Guide d'installation
Epson
Epson Stylus Photo PX730WD Instructions de montage
Epson
Epson 790 Manuel utilisateur
Epson
Epson Stylus Photo PX710W Series Mode d’emploi
Epson
Epson Stylus Color C60 Manuel utilisateur
Epson
Epson SC-S80600 Series Manuel utilisateur
Epson
Epson Stylus Color 500 Manuel utilisateur
Epson
Epson AcuLaser C2900N Manuel utilisateur
Epson
Epson Stylus C44 Mise à jour du firmware
