Envirovent PROFILE-100 Instructions de montage

PROFILE-100

Installation and Wiring Instructions

PROFILE-100 AXIAL EXTRACTOR FANS

Suitable for bathroom applications

Thank you for placing your confidence in EnviroVent by buying this product. It

has been manufactured following current technical safety regulations, production

and quality standards as laid down by the international Quality Standard ISO

9001. Please read this instruction booklet carefully before installing or starting up

the product. It contains important information on personal and user safety

measures to be followed whilst installing, using and carrying out maintenance

work on the equipment. Once the product has been installed, please pass this

booklet to the end user.

Check that the product is in perfect condition while unpacking. Any fault or

damage caused in origin is covered by the EnviroVent guarantee. Please make

sure that the product corresponds to the one you have ordered and that the

details on the instruction plate fulfil your requirements.

IMPORTANT:

BE SURE TO HAVE READ AND UNDERSTOOD THESE INSTRUCTIONS

BEFORE BEGINNING THE INSTALLATION PROCESS

SAFETY AND RECOMMENDATIONS

All wiring must comply with Building Regulations and the current I.E.E. Wiring

Regulations (BS7671) or the equivalent standards for your country.

The final installation should be examined and tested by a competent person.

This fan is IP44 rated.

Do not install near sources of heat in excess of 40°C.

Position the fan at the furthest distance from the main source of air

replacement in the room in order to achieve maximum airflow performance.

This appliance is not intended for use by young children or infirm persons

unless they have been adequately supervised by a responsible person to

ensure that they can use the appliance safely. Young children should be

supervised to ensure that they do not play with the appliance.

INSTALLATION: PROFILE –100

Fig.1

Ø 105 mm

INSTALLATION: PROFILE –100

Fig.2

Fig.3

Fig.5

Fig.4

Fig.6

Fig.7

Fig.8

20 % Hr

60/90

%Hr

60/90

t min

2/20

tmin

2/20

Fig.9

PROFILE-100 AXIAL EXTRACTOR FANS

Suitable for bathroom applications

INSTALLATION

IMPORTANT: before installing and wiring the unit, ensure that the mains supply

is disconnected.

PROFILE-100 should only be used in conjunction with fixed wiring.

Fig.1 1 –Grille

2 –Fixing screw for front cover

3 –Connection terminals

4 –Outlet

5 –Cable entry point

The PROFILE-100 is suitable for panel, ceiling or wall mounting (for wall

mounting applications using EnviroVent wall kit) (fig. 2).

Drill a hole in chosen position in the panel, ceiling or wall of size Ø105mm in

diameter. If the unit is to be installed with ducting, use standard duct size

Ø100mm.

The hole for the duct should be angled downwards to prevent rainwater

running through the duct into the unit.

Loosen the screw (2), which holds the grille in place (1) and remove grille.

Place the extractor against the internal wall or ceiling. For a wall mounted

fan the terminal block should be at the bottom. Mark the 4 screw hole

positions. Drill, plug and screw the extractor in position.

Check that the wall tube is not distorted and that the impeller turns freely.

Once the cable has been introduced through one of the cable points (5), fix

to the wall.

This fan must be installed by a competent person. Complete electrical wiring

of fan as outlined in the Wiring Instructions below. Then refit the grille and

tighten the screw (2).

WIRING

IMPORTANT: ENSURE THAT THE MAINS SUPPLY IS SWITCHED OFF

BEFORE MAKING ELECTRICAL CONNECTIONS.

The PROFILE is an extractor fan designed for a single-phase supply, with

voltage and frequency as indicated on the rating plate of the unit. The units are

manufactured with double insulation (Class ll) and therefore do not require an

earth connection.

• PROFILE – 100 S

This model uses the following wiring diagrams:

Fig.3. Fan operating through a light switch.

Fig.4. Fan operating through an independent switch.

• PROFILE – 100 P

Models fitted with on/off pullcord switch use the following wiring diagrams:

Fig.3. Fan operating through a light switch.

Fig.4. Fan operating through an independent switch or sensor.

• PROFILE – 100 T

Models fitted with adjustable timer.

The timer enables the fan to continue running for the selected period after the

switch has been turned off.

Fig.5. Fan operating through an independent switch.

Fig.6. Fan operating through a light switch.

The desired run-on time is selected by means of an adjuster positioned on the

printed circuit board (Fig.7), and is accessible once the grille (1) is removed.

• To reduce the run-on time, turn anticlockwise (min. 1 minute).

• To increase the run-on time, turn clockwise (max. 30 minutes).

• PROFILE – 100 HT

Models provided with an electronic humidistat, which can be adjusted from 60%

to 90%RH (relative humidity), and with a timer, adjustable between 2 and 20

minutes.

Specific recommendations

- In order to change the settings of the fan you will need to handle the controls

located on the PCB. These adjusters are fragile and must be handled with

care.

- In order to ensure correct measurement of humidity levels, the fan must be

installed in an area where there is good air circulation.

- Ensure that the fan is inside the room that it is to be installed in when setting

the humidity level.

- If the humidity level is consistently above 90%, the fan will continue to run

without stopping.

Operation

Case 1: Automatic operation (Fig.8).

The humidistat causes the extractor to operate automatically when the humidity

level in the room is higher than the set level. The extractor will stop automatically

when the humidity drops below the selected level and after the selected period,

set on the timer.

Case 2: Automatic with manual override.

Automatic operation as in case 1, but with the facility to override the humidistat

by means of the light switch (Fig.6), when the humidity level in the room is lower

than the selected level. In this case, the extractor continues to operate for the

period set on the timer, after the light switch has been switched off.

ATTENTION: When the humidity rises above the selected value, the

automatic option takes precedence over the manual and the unit cannot

then be switched off using a switch.

Settings:

The fans are set to operate at 60% relative humidity and with 2 minutes run-on

time. If the humidity in the room is lower than 60%, the fan will not turn on. If it is

higher, the fan will operate until the humidity level drops below 60%RH and then

runs for the length of time set by the timer. The desired humidity level and time

delay are set by means of adjusters positioned on the printed circuit board (fig. 9)

and accessible once the grille (1) has been removed.

The humidity is set by the adjuster. “% Hr”

- To increase the humidity setting turn anticlockwise (min.60 %)

- To reduce the humidity setting turn clockwise (max. 90 %)

The timer is set by the adjuster “t min.”

- To reduce the run-on time, turn anticlockwise (min. 2 minutes)

- To increase the run -on time, turn clockwise (max: 20 minutes).

ATTENTION: When the fan is operating on run-on time phase, it must finish

before adjusting to a new setting.

Note:

If the fan never turns on:

- Humidity adjuster is not at its lowest setting. Turn the adjuster anticlockwise

(do not force the adjuster) to the minimum setting.

- The fan is fitted in an area where there is no air flow.

- The humidity level in the room is below 60% RH.

If the fan never stops:

- Humidity adjuster is not at its highest setting. Turn the adjuster clockwise (do

not force the adjuster) to the maximum setting.

- The humidity level in the room is above 90% RH.

• PROFILE – 100 PIR

Models provided with a PIR (passive infra-red) detector and a “run on” timer (1 to

30 mins).

The unit starts automatically when a movement is detected within a maximum

distance of 2 metres (fig. 8) and will continue to operate for the set period.

The desired run-on time is selected by means of an adjuster positioned on the

printed circuit board (fig. 7) and accessible once the grille (1) has been removed:

- To reduce the run-on time, turn anticlockwise (min. 1 minute)

- To increase the run-on time, turn clockwise (max: 30 minutes).

CLEANING AND MAINTENANCE

IMPORTANT: DISCONNECT FROM THE MAINS SUPPLY BEFORE

CARRYING OUT CLEANING OR MAINTENANCE

To ensure optimum performance from you extract fan, it should be cleaned

regularly by a competent person.

AFTER SALES SERVICE

We recommend you not to dismantle or remove any other parts than those

mentioned, as any tampering would automatically cancel the guarantee. If you

detect any fault, contact EnviroVent on 01423 810810.

Thank you for choosing EnviroVent - the fastest growing ventilation company in

the UK.

And remember, if you have any problems please call our dedicated Technical

Team on the Hotline 0845 27 27 810.

Table des matières

Autres manuels Envirovent Ventilateur

Envirovent

Envirovent FILTERLESS EXTRACT FAN SELV Series Guide de démarrage rapide

Envirovent

Envirovent SILENT MV Series Instructions de montage

Envirovent

Envirovent energiSava 250 Manuel utilisateur

Envirovent

Envirovent SILENT Manuel

Envirovent

Envirovent OZEO Manuel utilisateur

Envirovent

Envirovent SLIMLINE 300 Guide de démarrage rapide

Envirovent

Envirovent filterless extractor fan Manuel utilisateur

Envirovent

Envirovent VENTY ECO2 Air Guide de démarrage rapide

Envirovent

Envirovent energisava 380 Manuel utilisateur

Envirovent

Envirovent SILENT MV-160/100 Instructions de montage

Envirovent

Envirovent SABIK 350 Manuel utilisateur

Envirovent

Envirovent PIV Manuel utilisateur

Envirovent

Envirovent CLASSIC-100 Manuel

Envirovent

Envirovent fliterless infinity fan 230v Manuel utilisateur

Envirovent

Envirovent PIV AIR SOURCE Manuel utilisateur

Envirovent

Envirovent PROFILE–150S Instructions de montage

Envirovent

Envirovent ECO dMEV LC Manuel utilisateur

Envirovent

Envirovent energiSava 200 Manuel utilisateur

Envirovent

Envirovent POWER-170 Instructions de montage

Envirovent

Envirovent SILENT Manuel

Envirovent

Envirovent kudos Manuel

Envirovent

Envirovent ECO dMEV LC Manuel

Envirovent

Envirovent PIV Manuel utilisateur

Envirovent

Envirovent Slimline 150 Guide de démarrage rapide

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage