Envirovent Slimline 150 Guide de démarrage rapide

SLIMLINE 150

INSTALLATION GUIDE FOR ENGINEER / INSTALLER

01 Slimline 150

01423 810 810

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

Safety

IMPORTANT

Be sure to have read and understood these

instructions before beginning the installation

process.

PRE-INSTALLATION CHECK LIST

Make sure that the unit can physically ﬁt in to

the desired location.

Electrical Connection

The unit requires a continuous electrical

power supply. Connection to the ﬁxed

wiring must be made outside the unit in a

suitable location. The unit must be able to

be disconnected from the mains supply after

installation. The unit must be earthed and a

suitable isolator having a minimum contact

separation of 3.0mm must be used to provide

isolation for the unit.

The power cable running into the unit must

remain the supplied ﬂexible cable. If the

power cable becomes damaged, it must be

replaced by EnviroVent, an authorised service

agent for your region/ country, or a similarly

qualiﬁed person in order to avoid a hazard.

Do not remove or tamper with any electronic

components inside the unit.

All wiring must comply with Building

Regulations and the current IET Wiring

Regulations (BS7671 in the UK) or equivalent

standards for other countries. The ﬁnal

installation should be examined and tested

by a qualiﬁed electrician.

This product is not suitable for use with a

Type AC RCD

SAFETY AND RECOMMENDATIONS

• This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made

by children without supervision.

Installation must take place under:

• Quality requirements ventilation systems

dwellings.

• Quality requirements balanced ventilation

in dwellings.

• The regulations for ventilation of dwellings

and residential buildings.

• The safety regulations for low-voltage

installations.

• The regulations for connection to interior

sewers in dwellings and residential

buildings.

• Any additional regulations of the local

utilities.

• The installation instructions for the

Slimline 150

AFTER INSTALLING THIS UNIT,

PLEASE PASS ONTO END USER DO NOT THROW AWAY

02 Technical Speciﬁcations

Before you begin to install the heat recovery unit, check that it has been supplied complete and undamaged.

The Slimline 150 unit should include the following components:

1. Heat recovery appliance

2. Wall mounting bracket kit; - 2x suspension strips

3. Duct connecting kit; - 4x collars Ø125 mm

4. Documentation set; - 1x installation instructions

5. Connecting kit; - Mounting material collars, including 16 ﬁxing screws

- Connectors : 2-pole screw connector (eBus) and 9-pole screw connector only

for Plus version)

6. Control unit with operating manual (packaged separately)

03 Slimline 150

01423 810 810

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

The EnviroVent Slimline 150 is a ventilation

unit with heat recovery with a maximum

ventilation capacity of 150 m3/h and low-

energy fans.

Slimline 150 Features:

• Steplessly adjustable air ﬂow rates through

a control unit (supplied with appliance,

packaged separately).

• Filter indication on the control unit / multiple

switch.

• A completely new intelligent frost protection

system.Thisensuresthatevenatlowoutdoor

temperatures the appliance’s performance

remains optimal and that, if necessary, it

activates the standard preheater.

• Low sound level

• Comes as standard with automatic bypass

valve

• Constant ﬂow control

• Low energy consumption

• High efﬁciency

Slimline 150 is available in two types:

• Slimline 150

• Slimline 150 Plus

Compared to the Slimline 150, the Slimline

150 Plus has a more extensive control board

which increases the connection options.

These installation instructions describe both

the standard Slimline 150 and the Slimline

150 Plus.

With the aid of the supplied mounting brackets,

the Slimline 150 (Plus) can be mounted

either on the wall or on the ceiling. For the

correct position of the connection ducts and

dimensions see page 6.

When ordering an appliance always state

the correct type; subsequent conversion to a

different version is highly labour-intensive.

The Slimline 150 comes ready to wire into the

230V mains fused spur.

The settings of the appliance are programmed

so the control unit can be used, but connection

of a simple 4-way switch is possible as well.

If a 4-way switch is installed instead of a

control unit, the settings of the appliance can

only be changed with a laptop.

Connecting a combination of control unit and

multiple switch is another option.

02 Technical Speciﬁcations

AFTER INSTALLING THIS UNIT,

PLEASE PASS ONTO END USER DO NOT THROW AWAY

Supply voltage (V/Hz) 230/50 Protection degree IP30

Dimensions

(w x d x h) (mm) 1000 x 660 x 198 Duct diameter (mm) Ø125

External discharge 3/4 Weight (kg) 24.5

Filter class G4/G4 or G4/F7

Fan factory setting

(control unit)

MAX

4-Way switch 1 2 3

Ventilation capacity

(m3/h) 30 75 100 125 150

Permissible

resistance ducts

system (Pa)

2-6 13-38 22-66 35-105 50-150

Rated power (excl.

pre-heater) (W) 11-12 19-27 27-37 38-52 53-72

Rated current (excl.

pre-heater) (A) 0.14-0.15 0.20-0.28 0.27-0.35 0.36-0.47 0.49-0.64

Rated current (incl.

optional pre-heater)

(A)

2.4

Cos φ0.34 0.42 0.44-0.47 0.46-0.48 0.47-0.49

02 Technical Speciﬁcations

05 Slimline 150

01423 810 810

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

100

150

200

0 25 50 75 100 125 150 175

= [W]

812

Sound Power

Ventilation

capacity (m3/h) 45 75 105 150

Sound power

level Lw (A)

Static pressure

(Pa) 10 50 100 25 50 100 50 100 50 100

Housing emission

dB(A) 24 33 39 33 35 40 38 41 44 45

Duct “from

dwelling” dB(A) 27 36 42 34 37 42 40 43 46 47

Duct “to dwelling”

dB(A) 41 49 58 50 53 57 57 60 62 64

Note: In practice, the value may deviate 1 dB(A) as a result of measuring tolerances.

(Pa)

(m3/h)

Note: The value stated in the circle is the capacity per fan (in Watt)

02 Technical Speciﬁcations

AFTER INSTALLING THIS UNIT,

PLEASE PASS ONTO END USER DO NOT THROW AWAY

1. To dwelling

2. To atmosphere

3. From dwelling

4. From

atmosphere

5. Electric connections

6. Connection condensate discharge

02 Technical Speciﬁcations





07 Slimline 150

01423 810 810

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

1. Extract air ﬁlter

2. Indoor temperature sensor

3. Bypass

4. Condensate bin

5. Extract fan

6. Locking screw front panel

(mounted in front panel)

7. Connector X14

8. Control board

9. Connector X4

10. Condensate discharge

11.Supply air ﬁlter

12.Preheater

13. Outdoor temperature sensor

14.Heat exchanger

15. Supply fan

16. Modular connector multiple switch

17. Service connector

18. Sleeve low voltage cable

19. Sleeve cable 230V postheater or

extra preheater

20. Mains cable 230V

21.9-pole connector (only for Plus version)

22. Connector eBus

23. Fall protection front panel

02 Technical Speciﬁcations

AFTER INSTALLING THIS UNIT,

PLEASE PASS ONTO END USER DO NOT THROW AWAY

The appliance is supplied ready to wire into

the fuse spur and operates fully automatically.

The extracted indoor air heats up the fresh,

clean outdoor air. That saves energy and fresh

air is sent to the required rooms.

The control system has four ventilation

modes. The air ﬂow rate can be adjusted per

ventilation mode. The constant volume control

system ensures that the air ﬂow rate of the

supply and extract fans is always delivered

despite any resistance encountered in the

ductwork.

The standard bypass valve makes it possible

to supply fresh outside air that is not heated

by the heat exchanger. Particularly during

summer nights it is desirable to supply cooler

outside air. In this mode the hot air in the

dwelling is replaced by cooler outside air as

far as possible.

The bypass valve opens and closes

automatically when a number of conditions

are satisﬁed (refer to the table below for

bypass conditions).

The operation of the bypass valve can be

adjusted in step number 5, step number 6

and step number 7 in the settings menu (see

pages 39-41).

To prevent freezing of the heat exchanger

at extremely low outdoor temperatures, the

Slimline 150 features an intelligent frost

control. Temperature sensors measure the

temperatures across the heat exchanger and,

if necessary, the preheater is switched on.

This guarantees a proper ventilation balance,

even at very low outdoor temperatures.

If, with switched on standard preheater(s),

the exchanger temperature still starts to drop

below zero, stepless unbalance is created in

the appliance.

The user information menu shows when the

Slimline 150 frost control system is activated

(see page 19).

Bypass valve open

-The outdoor temperature is higher than 10°C and

-The outdoor temperature is lower than the indoor temperature in the dwelling

and

-The temperature in the dwelling is higher than the temperature set at step

no.5 in the settings menu

(set a standard at 24°C).

Bypass valve closed

-The outdoor temperature is lower than 10°C or

-The outdoor temperature is higher than the indoor temperature in the dwelling

-The temperature from the dwelling is lower than the temperature set at

step no. 5 in the settings menu minus the set temperature by the hysteresis

(tolerance) (step no. 6), this temperature is factory set at 22°C (24.0°C minus

2.0°C).

02 Technical Speciﬁcations

09 Slimline 150

01423 810 810

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

02 Technical Speciﬁcations

The Slimline 150 is also available as a Plus

version. This version is equipped with a

different control board with 2 additional

connectors (X14 & X15) with more connection

options for various applications.

Only the Plus is equipped with a 9-pole

connector (connected to X15 on control

board) that is accessible from the outside of

the appliance.

If a postheater or extra preheater is connected

to connector X14 (accessible after opening

the front panel ) the installer must feed

the connected 230 Volt cable to outside

the appliance through a strain reliever. For

this strain reliever (not supplied with the

appliance) a plug must be removed from

the position where this strain relief must be

placed.

See page 32 for more information on the

connection possibilities of connectors X14

and X15.

A. 9-pole connector

B. Hole for gland to be mounted

by installer (for sleeve cable

postheater/ extra preheater).

Slimline 150 Plus

Autres manuels pour Slimline 150

Table des matières

Autres manuels Envirovent Ventilateur

Envirovent

Envirovent cyclone 7 Manuel utilisateur

Envirovent

Envirovent PIV AIR SOURCE Manuel utilisateur

Envirovent

Envirovent kudos Manuel

Envirovent

Envirovent fliterless infinity fan 230v Guide de démarrage rapide

Envirovent

Envirovent energiSava 200 Manuel utilisateur

Envirovent

Envirovent POWER-170 Instructions de montage

Envirovent

Envirovent OZEO Manuel utilisateur

Envirovent

Envirovent ECO DMEV+ LC Manuel utilisateur

Envirovent

Envirovent PROFILE-100 Instructions de montage

Envirovent

Envirovent filterless extractor fan Manuel utilisateur

Envirovent

Envirovent energisava250 Manuel utilisateur

Envirovent

Envirovent SILENT Manuel

Envirovent

Envirovent FILTERLESS EXTRACT FAN SELV Series Guide de démarrage rapide

Envirovent

Envirovent Damp Pro DP-EVL Manuel utilisateur

Envirovent

Envirovent SILENT MV Series Instructions de montage

Envirovent

Envirovent MEV SPIDER Manuel utilisateur

Envirovent

Envirovent ATMOS WALL Manuel utilisateur

Envirovent

Envirovent PROFILE–150S Instructions de montage

Envirovent

Envirovent energiSava 300 Manuel utilisateur

Envirovent

Envirovent SELV Guide de démarrage rapide

Envirovent

Envirovent SLIMLINE 300 Guide de démarrage rapide

Envirovent

Envirovent ECO dMEV LC Manuel utilisateur

Envirovent

Envirovent ECO DMEV Manuel utilisateur

Envirovent

Envirovent fliterless infinity fan 230v Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage