Enphase Envoy-S Manuel utilisateur

Getting Started Guide:

Envoy-S Internet Connectivity

This getting started guide is for the on-site

electrician or foreman who is responsible for

ensuring the Enphase Envoy-S™ is connected to

the Enphase Enlighten™ web monitoring system

before leaving the job site.

This guide applies to all Envoy models that look

like these:

Before You Start

Download the latest version of Enphase Installer

Toolkit™ before you leave the office. If you have

never logged into Toolkit, use your Enlighten

installer credentials to log in. This unlocks the

application for your ongoing use.

This step also ensures you have the latest

software upgrade package on your mobile device

in case you are directed to upgrade the Envoy-S in

the field.

Signs of Success!

When the Envoy-S is

connected to the Internet and

communicating with Enlighten,

the Network Communications LED (topmost) on

the Envoy lights solid green.

In addition, the Installer Toolkit

will verify that the Envoy is

connected and

communicating with

Enlighten.

Cellular Connectivity with Enphase Mobile

Connect

Complete the following steps

to install the Enphase Mobile

Connect™ modem:

1. Connect the cellular

antenna to the connector

labeled CELL on the

modem.

2. Mount the modem on a wall

using the slide-in-tab, or

attach the rubber feet and

mount on a flat surface.

If the Enphase AC Combiner

Box™ is installed, the

modem can sit on the bottom

of the box.

3. First, connect the USB cable to the USB port(s)

on the Envoy-S.

4. Then, connect the mini-USB connector to the

Mobile Connect modem.

The power LED lights when the modem has power.

After about two minutes, the Link Status (LS) LED

flashes to indicate a network connection.

• The Signal LEDs indicate signal strength

according to the Signal LED table below.

• Signal strength of 1 bar is adequate for data

transmission to Enlighten.

Within three minutes the Envoy-S Network

Communications LED lights solid

green, indicating a successful

connection to the Internet

and to Enlighten.

Wi-Fi Connection

There are two ways to configure the Wi-Fi

connection. Follow one of these methods to

connect the Envoy to the Internet and Enlighten.

Method A: Use the WPS function on the router.

1. Verify that there is no Ethernet cable connected

to the Envoy.

2. Confirm the homeowner’s router supports WPS

function. (WPS stands for Wi-Fi Protected

Setup.) Look for a button on the router with a

symbol like one of these.

3. Once you find WPS button on the wireless

router, press and hold it for a few seconds. On

most routers, a WPS LED begins flashing.

(Pressing the WPS button on the router

activates device pairing.)

4. Initiate the WPS

pairing at the Envoy

by pressing and

holding the AP

Mode button for five

seconds .

NOTE: If the AP Mode button is

held for fewer than five seconds,

AP mode will be initiated, but not

WPS pairing.

If AP mode is enabled

accidentally, the Envoy’s

network will be visible on your

Wi-Fi settings and the AP

Mode LED will be lit solid

green.

5. To disable AP mode, touch the AP Mode

button for one second, then release it.

Method B: Manually configure Wi-Fi connection.

1. Click on the Network tab.

2. Select the homeowner’s Wi-Fi

network from the list of available

networks.

3. Connect to the homeowner’s Wi-

Fi network. This may require that

you enter the homeowner’s

network password.

Within three minutes the Envoy-S

Network Communications LED

lights solid green to indicate

successful connection to the Internet

and to Enlighten.

Hard-Wire Ethernet

The most reliable Internet connection, when Mobile

Connect or Wi-Fi are not options, is a hard-wired

Ethernet connection. In a hard-wire connection you

must use an Ethernet cable (Use Cat5E or Cat6

UTP – Do not use STP cable) to connect to the

homeowner’s router on one end and directly to the

Envoy on the other end. This is a good option when

the Ethernet cable will span a distance of no more

than 100m (328 feet).

If it is not physically possible to hard-wire the

connection, use Ethernet bridges instead.

Envoy

Broadband

Router

Ethernet Connection Using Ethernet

Bridges

Use Ethernet bridges when the distance between

the Envoy and the router is too great, or when it is

impractical to span the distance between them with

Ethernet cable.

Complete the following steps to enable an Ethernet

connection using Ethernet bridges.

Bridge one:

1. Connect one end of the Ethernet “jumper”

cable to the bridge and the other end to the

Envoy.

2. If an AC Combiner Box is

installed, plug the bridge

into the outlet inside the

box and then connect the

cable to the Ethernet port

on the bottom of the

Envoy-S.

3. If you are not using an AC Combiner Box, plug

the bridge into a dedicated outlet near the

Envoy’s final install location and then connect

the cable to the Ethernet port on the bottom of

the Envoy-S.

Bridge two:

1. Connect one end of the Ethernet “jumper”

cable to the bridge and the other end to an

unused port on the router.

2. Plug the bridge into a dedicated

outlet near the router.

Within three minutes the Envoy-S Network

Communications LED lights solid green to indicate

a successful connection to the Internet

and to Enlighten.

When to Contact the Your Office

If you are unable to confirm the Envoy is

communicating with Enlighten, contact your

operations or installation support staff for

assistance.

Autres manuels pour Envoy-S

Autres manuels enphase Porte

enphase

enphase ENP-ENV-S-EM-230 Mode d’emploi

enphase

enphase COMMS-KIT-INT-02 Manuel utilisateur

enphase

enphase ENV-S-EM-230 Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase ENV-S-AM1-230-60 Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase ENV-S-EM-230-LF-KIT Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase IQ Combiner 3C-ES Manuel utilisateur

enphase

enphase Envoy-S Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase CT-100-SPLIT ROW Manuel utilisateur

enphase

enphase Envoy Communications Gateway Manuel utilisateur

enphase

enphase Enboy R Guide de démarrage rapide

enphase

enphase Envoy-S Standard ENV-S-WB-230-F Manuel utilisateur

enphase

enphase ENV-S-WM230 Manuel utilisateur

enphase

enphase IQ System Controller 2 Manuel utilisateur

enphase

enphase Enphase Envoy-S Metered Manuel utilisateur

enphase

enphase ENV-S-AM1-120 Mode d’emploi

enphase

enphase ENV-S-WM230 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur