EnGenius EAP600 Manuel utilisateur

Quick Installation Guide

EAP600

Wireless-N 300 + 300Mbps Long Range Ceiling Mount Dual

Concurrent AP

Please verify contents of the box before continuing to set up the EAP600.

EAP600 Access Point

12V/2A 100V~240V Power Adaptor

RJ-45 Ethernet Cable

Mounting Bracket

Wall/Ceiling Mounting Hardware Kit

T-Rail Mounting Hardware Kit

CD with User's Manual

Connecting the EAP600

1) Ensure that the computer in use has an Ethernet Card (RJ-45 Ethernet Port). For more information,

verify with User Manual.

2) Connect one end of the Category 5e Ethernet cable into RJ-45 port of the EAP600 and the other

end to the RJ-45 port on the computer that will use the EAP600. Ensure that the cable is securely

connected to both the EAP600 and the Computer.

3) Connect the Power DC Inlet to the DC-IN port of the EAP600 and the Power to the electrical out.

Note: EAP600 supports both IEEE 802.3at PoE(Power over Ethernet) and regular power adapter. You

should use either one as the power source. Please do not apply both at the same time.

IP address configuration

1) After ensuring the EnGenius device is powered on and plugged in, ensure that your computer is

on.

2) For the next steps, refer to your Operating System User Manual.

3) Once your computer is on, ensure that your TCP/IP is set to On or Enabled. (In the control panel,

double click Network Connections and then double click on the connection of your Network

Interface Card (NIC). Select Internet Protocol (TCP/IP) and then click on the Properties button.)

4) If your PC is already on a computer network, ensure that you have set it to a Static IP Address on

the interface (or Ethernet card that will use the EAP600) as 192.168.1.21 and the Subnet Mask

address as 255.255.255.0. (Select Use the following IP Address radio button). Once the

computer has been prepared, proceed to setting up the EAP600.

EAP600 Setup

1) To configure EAP600, open a web browser (example: Microsoft Internet Explorer, Mozilla Firefox,

Google Chrome, etc.).

2) In the address bar of the web browser, enter 192.168.1.1 (the default IP address of the EAP600)

and hit enter.

3) A login screen will appear. By default, the username of the EAP600 is admin and the password is

admin. Enter the current username and password of the EAP600 and then click Login. Refer to

the EAP600 user manual on how to change the

username and password.

4) After clicking Login with the correct username and

password, the EAP600 Main Menu will appear. If you

are successful, proceed to setting up the wireless

connection.

Switching Between Operating Modes

This device can operate in the following modes: Access Point, WDS AP, WDS Bridge and Repeater.

A. Click on the Operation Mode link under the System navigation drop-down menu.

B. Operating Mode: Select an operating mode from the list (Access Point, WDS AP, WDS Bridge or

Repeater) and then click on the Apply button.

C. All basic setup is completed. Note: The wireless connection is not secure. To setup security on the

EAP600, refer to the EAP600 User Manual.

http://192.168.1.1

Mounting the EAP600

Using the provided hardware, the EAP600 can be attached to a ceiling or wall.

To attach the EAP600 to a ceiling or wall using the mounting bracket:

1) Attach the mounting bracket to the wall or ceiling using the provided wall/ceiling mounting

hardware kit.

2) Insert the provided short screws into the bottom cover of the EAP600.

Leave enough of the screws exposed to ensure that the unit can be attached to the mounting bracket.

If extra space is required, use the provided spacers and long screws from the T-Rail mounting

hardware kit to increase the space between the unit and the mounting bracket.

3) Mount the EAP600 on the mounting bracket by rotating the unit clockwise about 90 degrees to

secure it in place.

To attach the EAP600 to a ceiling using the provided T-rail connectors:

1) Attach the T-rail connectors to the bottom cover of the EAP600 using the provided short screws.

Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in (2.38cm) and 9/16in

(1.43cm).

If extra space is required to accommodate drop ceiling tiles, use the provided spacers and long screws.

2) Line up the connected T-rail connectors with an appropriately sized rail and press the unit onto

the rail until it snaps into place.

Note: To protect your EAP600, use the Kensington security slot to attach a cable lock (cable lock is not

included).

Autres manuels pour EAP600

Table des matières

Autres manuels EnGenius Point d'accès sans fil

EnGenius

EnGenius EAP350 Manuel utilisateur

EnGenius

EnGenius ENS202 Manuel utilisateur

EnGenius

EnGenius M8000 Manuel utilisateur

EnGenius

EnGenius EOC-8610 Series Manuel utilisateur

EnGenius

EnGenius ENH700EXT Manuel utilisateur

EnGenius

EnGenius EOC-3220 Manuel utilisateur

EnGenius

EnGenius EOC-2610 Manuel utilisateur

EnGenius

EnGenius ENS200 Manuel utilisateur

EnGenius

EnGenius ECB1221R Manuel utilisateur

EnGenius

EnGenius EWS850AP Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

EnGenius

EnGenius ESR-1221N Manuel utilisateur

EnGenius

EnGenius EOC-2610 Manuel utilisateur

EnGenius

EnGenius EOC5510 Manuel utilisateur

EnGenius

EnGenius ENH900EXT Manuel utilisateur

EnGenius

EnGenius ECB-3220 Manuel utilisateur

EnGenius

EnGenius ENS1750 Manuel utilisateur

EnGenius

EnGenius ENH210EXT Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

EnGenius

EnGenius EWS375-FIT Manuel utilisateur

EnGenius

EnGenius EOC5611P Manuel utilisateur

EnGenius

EnGenius M2000 Manuel utilisateur

EnGenius

EnGenius ECB600 Manuel utilisateur

EnGenius

EnGenius M36 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur