INSTALLATION INSTRUCTIONS
-02- -03--01-
DESCRIPTION
FEATURES
ZWN-RSM2
Range...................................................................Up to 100 feet line of sight
SPECIFICATIONS
between the Wireless Controller and the closest Z-Wave receiver module.
INSTALLATION
1. WARNING: To avoid fire, shock, or death. Turn off power at circuit breaker
or fuse and test that power is off before wiring.
2. Remove wall plate and switches mounting screws.
3. Carefully remove these existing switches from the switch box.
Wiring Diagram:
4. Disconnect the wiring from these existing switches.
WARNINGS AND CAUTIONS
To be installed and/or used in accordance with appropriate electrical codes
and regulations. Exercise extreme caution when using Z-Wave devices to
control appliances. Operation of the Z-Wave device may be in a different
please consult a qualified electrician.
room than the controlled appliance, also an unintentional activation may
occur if the wrong button on the remote is pressed. Z-Wave devices may
automatically be powered on due to timed event programming.Depending
upon the appliance, these unattended or unintentional operation could
If you are unsure or uncomfortable about performing the installation,
possibly result in a hazardous condition.
Z-Wave enabled devices should never be used to supply power to, or
control the On/Off status of medical and/or life support equipment.
6. Check connections to be sure they are tight and no bare conductors are exposed.
8. Attach the wall plate.
9. Restore power at the circuit breaker and test the system.
, then wire these existing switches.
5. Connect the ZWN-RSM2 module as shown in the wiring diagram.
7. Insert the ZWN-RSM2 module into the box first
Operating Temperature..............................................................32° F-104° F
Smart Dual Relay Switch Module
Maximum Load requirement.................................................................10A×2
Voltage.........................................................................120-277VAC, 50/60Hz
Z-Wave Frequency.............................................................. 908.42MHz(US)
Size................................................................................2.02'' ×1.71'' ×0.62''
Z-Wave unifies all your home electronics into an integrated wireless network
and helps them talk to each other. Any Z-Wave enabled item can be added
to the network, and making your home electronics fully compatible.
Please consult an electrician if you have trouble identifying the type of wiring
circuit you wish to convert or if you do not feel confident in your ability to
convert the circuit to Z-Wave control.
Work with existing light switches, required neutral wire
Slim size module with build in Z-Wave technology
On/Off control via Z-Wave controller, manual wall switch
Acts as a Z-Wave repeater to extend the range
device is designed to act as a wireless repeater. Once the ZWN-RSM2 module
switch. This ZWN-RSM2 module is a Z-Wave enabled device and is fully
compatible with any Z-Wave enabled network. In a Z-Wave network, each
intended device is reached. This ensures that the
signal is received by its intended destination by routing the signal around
The ZWN-RSM2 Switch Module is a component of lighting control system, it
can not be used separately but should turn an existing switch into a Z-Wave
device to another until the
obstacles and radio dead spots.
is installed and setup with in your wall, it will retransmit the RF signal from one
Load 2
Hot
Neutral
Aux 2
Line
Neutral
Line
(Black)
(White)
Neutral
Switch 2
Load 1
Aux 1
Neutral
Line
Switch 1
Basic Operation
OPERATIONS
The connected device can be turned ON in two ways:
2. Z-Wave remote controller.
Program Button Antenna
1. Manual control with the button on the connected switch.
TIPS FOR ARRANGING THE ANTENNA:
Locate the antenna as far from metal elements as possible to prevent interferences.
Metal surfaces in the direct vicinity of the antenna may impair signal reception.
Do not cut or shorten the antenna - its length is perfectly matched.
Manual Control
as same as traditional switch.
Turn the household appliance on/off by pressing the button on the connected switch
to perform manual function, this function is
Remote Control
When the ZWN-RSM2 switch module is included in a Z-Wave network, it can be
turned on/off remotely by a portable controller or a Z-Wave enabled gateway
controller.
Z-Wave network inclusion/exclusion
of the connected switch with Aux1 line (not Aux2 line)
Press and release the program button of ZWN-RSM2 module that setting it into
learning mode to include/exclude the module with Z-Wave network. Flick 3 times
if the Z-Wave network failed to add ZWN-RSM2, please try exclusion first.
for one second. For controller inclusion/exclusion mode,
will also set the ZWN-RSM2
manual of the controller.
module into learning mode
please refer to the
