Endress+Hauser Hart Micropilot FMR60B Caractéristiques techniques

Products Solutions Services

Brief Operating Instructions

Micropilot FMR60B

PROFINET with Ethernet-APL

Free space radar

advanced physical layer

These Brief Operating Instructions are not a substitute for the

Operating Instructions pertaining to the device.

Detailed information is provided in the Operating Instructions

and other documentation.

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smartphone/tablet: Endress+Hauser Operations app

KA01611F/00/EN/01.23-00

71610090

2023-04-22

Micropilot FMR60B PROFINET with Ethernet-APL

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

Micropilot FMR60B PROFINET with Ethernet-APL Table of contents

Endress+Hauser 3

Table of contents

1 Symbols .......................................................................... 4

1.1 Safety symbols ........................................................................ 4

1.2 Symbols for certain types of information and graphics ........................................... 4

2 Requirements for personnel ...................................................... 5

3 Intended use ...................................................................... 5

4 Workplace safety ................................................................. 6

5 Operational safety ................................................................ 6

6 Product safety .................................................................... 6

7 Incoming acceptance .............................................................. 7

8 Product identification ............................................................. 7

8.1 Nameplate ........................................................................... 7

8.2 Manufacturer address ................................................................... 8

9 Storage and transport ............................................................. 8

9.1 Storage conditions ..................................................................... 8

9.2 Transporting the product to the measuring point ............................................... 8

10 Mounting ......................................................................... 8

10.1 General instructions .................................................................... 8

10.2 Mounting requirements ................................................................. 9

10.3 Mounting the measuring device ...........................................................11

10.4 Post-mounting check .................................................................. 15

11 Electrical connection ............................................................ 16

11.1 Connecting requirements ............................................................... 16

11.2 Connecting the device .................................................................. 18

11.3 Ensuring the degree of protection ......................................................... 24

11.4 Post-connection check ..................................................................24

12 Operation ....................................................................... 25

12.1 Reading off the device locking status ....................................................... 25

12.2 Reading off measured values ............................................................. 25

12.3 Adapting the device to process conditions ................................................... 25

13 Commissioning .................................................................. 25

13.1 Preliminaries ........................................................................ 25

13.2 Function check ....................................................................... 25

13.3 Establishing a connection via FieldCare and DeviceCare ......................................... 26

13.4 Configuring the operating language ....................................................... 27

13.5 Configuring the device ................................................................. 28

Symbols Micropilot FMR60B PROFINET with Ethernet-APL

4 Endress+Hauser

1 Symbols

1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.2 Symbols for certain types of information and graphics

Permitted

Procedures, processes or actions that are permitted

Preferred

Procedures, processes or actions that are preferred

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Reference to graphic

Notice or individual step to be observed

Series of steps

Result of a step

1, 2, 3, ...

Item numbers

A, B, C, ...

Views

Safety instructions

Observe the safety instructions contained in the associated Operating Instructions

Micropilot FMR60B PROFINET with Ethernet-APL Requirements for personnel

Endress+Hauser 5

2 Requirements for personnel

The personnel must fulfill the following requirements for its tasks:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Personnel must be authorized by the plant owner/operator.

‣Personnel must be familiar with federal/national regulations.

‣Before starting work: personnel must read and understand the instructions in the manual

and supplementary documentation as well as the certificates (depending on the

application).

‣Personnel must follow instructions and comply with general policies.

3 Intended use

Application and media

The measuring device described in these Operating Instructions is intended for continuous,

non-contact level measurement in liquids, pastes and sludges. Because of its operating

frequency of approx. 80 GHz, a maximum radiated peak power of 6.3 mW and an average

output power of 63 µW, unrestricted use outside of closed, metallic vessels is also permitted

(for example over basins or open channels). Operation does not pose any danger whatsoever

to humans and animals.

If the limit values specified in the "Technical data" and the conditions listed in the instructions

and additional documentation are observed, the measuring device may be used for the

following measurements only:

‣Measured process variables: level, distance, signal strength

‣Calculated process variables: volume or mass in vessels of any shape; flow through

measuring weirs or channels (calculated from the level by the linearization functionality)

To ensure that the measuring device remains in proper condition for the operation time:

‣Use the measuring device only for media against which the process-wetted materials are

adequately resistant.

‣Observe the limit values in the "Technical data".

Incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Avoid mechanical damage:

‣Do not touch or clean device surfaces with pointed or hard objects.

Clarification of borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability.

Residual risks

Due to heat transfer from the process as well as power loss in the electronics, the temperature

of the electronics housing and the assemblies it contains (e.g. display module, main

Workplace safety Micropilot FMR60B PROFINET with Ethernet-APL

6 Endress+Hauser

electronics module and I/O electronics module) may rise to 80 °C (176 °F). When in operation,

the sensor may reach a temperature close to the medium temperature.

Danger of burns from contact with surfaces!

‣For elevated fluid temperatures, ensure protection against contact to prevent burns.

4 Workplace safety

When working on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

‣Switch off the supply voltage before connecting the device.

5 Operational safety

Risk of injury!

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate the risk of danger to persons or the facility when the device is used in the

approval-related area (e.g. explosion protection, pressure equipment safety):

‣Check the nameplate to verify if the device ordered can be put to its intended use in the

approval-related area.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of this manual.

6 Product safety

This device is designed in accordance with good engineering practice to meet state-of-the-art

safety requirements, has been tested, and left the factory in a condition in which it is safe to

operate.

It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

Micropilot FMR60B PROFINET with Ethernet-APL Incoming acceptance

Endress+Hauser 7

7 Incoming acceptance

DELIVERY NOTE

1 = 2

A0016870

Check the following during incoming acceptance:

• Is the order code on the delivery note (1) identical to the order code on the product sticker

(2)?

• Are the goods undamaged?

• Do the data on the nameplate correspond to the order specifications and the delivery note?

• Is the documentation provided?

• If required (see nameplate): are the Safety Instructions (XA) provided?

If one of these conditions is not met, please contact the manufacturer's sales office.

8 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣Device Viewer(www.endress.com/deviceviewer); manually enter the serial number from

the nameplate.

 All the information about the measuring device is displayed.

‣Endress+Hauser Operations app; manually enter the serial number indicated on the

nameplate or scan the 2D matrix code on the nameplate.

 All the information about the measuring device is displayed.

8.1 Nameplate

The information that is required by law and is relevant to the device is shown on the

nameplate, e.g.:

• Manufacturer identification

• Order number, extended order code, serial number

• Technical data, degree of protection

Storage and transport Micropilot FMR60B PROFINET with Ethernet-APL

8 Endress+Hauser

• Firmware version, hardware version

• Approval-related information, reference to Safety Instructions (XA)

• DataMatrix code (information about the device)

8.2 Manufacturer address

Endress+Hauser SE+Co. KG

Hauptstraße 1

79689 Maulburg, Germany

Place of manufacture: See nameplate.

9 Storage and transport

9.1 Storage conditions

• Use the original packaging

• Store the device in clean and dry conditions and protect from damage caused by shocks

9.1.1 Storage temperature range

See Technical Information.

9.2 Transporting the product to the measuring point

LWARNING

Incorrect transport!

The housing or sensor can be damaged or pull off. Risk of injury!

‣Transport the device to the measuring point in its original packaging or by the process

connection.

‣Always secure lifting equipment (slings, eyes, etc.) at the process connection and never lift

the device by the electronic housing or sensor. Pay attention to the center of gravity of the

device so that it does not tilt or slip unintentionally.

10 Mounting

10.1 General instructions

LWARNING

Loss of protection rating if the device is opened in a wet environment.

‣Only open the device in a dry environment!

Micropilot FMR60B PROFINET with Ethernet-APL Mounting

Endress+Hauser 9

1. Install the device or turn the housing so that the cable entries do not point upwards.



A0029263

2. Always firmly tighten the housing cover and the cable entries.

3. Counter-tighten the cable entries.

4. A drip loop must be provided when laying the cables.

10.2 Mounting requirements

10.2.1 Internal vessel fittings

A0031777

Avoid internal fittings (point level switches, temperature sensors, struts, vacuum rings,

heating coils, baffles etc.) inside the signal beam. Pay attention to the beam angle α.

Mounting Micropilot FMR60B PROFINET with Ethernet-APL

10 Endress+Hauser

10.2.2 Avoiding interference echoes

A0031813

Metal deflector plates, installed at an angle to scatter the radar signals, help prevent

interference echoes.

10.2.3 Vertical alignment of antenna axis

Align the antenna so that it is perpendicular to the product surface.

The maximum reach of the antenna can be reduced, or additional interference signals

can occur, if the antenna is not installed perpendicular to the product.

10.2.4 Radial alignment of the antenna

Based on the directional characteristic, radial alignment of the antenna is not necessary.

10.2.5 Optimization options

Mapping

Measurement can be optimized by electronically suppressing interference echoes.

See the Confirm distance parameter.

Autres manuels pour Hart Micropilot FMR60B

Table des matières

Autres manuels Endress+Hauser Instrument de mesure

Endress+Hauser

Endress+Hauser Turbimax CUE21 Manuel utilisateur

Endress+Hauser

Endress+Hauser analytikjena Biometra TOne Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP43 Manuel utilisateur

Endress+Hauser

Endress+Hauser MODBUS RS485 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93T Portable Manuel utilisateur

Endress+Hauser

Endress+Hauser SpectraSensors SS2100 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiline System CA80NO Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex FMP50 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Smartec S CLD132 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promass E 200 Manuel

Endress+Hauser

Endress+Hauser Deltabar PMD78B Manuel utilisateur

Endress+Hauser

Endress+Hauser LT5 Caractéristiques techniques

Endress+Hauser

Endress+Hauser memo-graph RSG10 Manuel utilisateur

Endress+Hauser

Endress+Hauser Prothermo NMT 539 Manuel utilisateur

Endress+Hauser

Endress+Hauser FMU 40 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiline Control CDC90 Manuel utilisateur

Endress+Hauser

Endress+Hauser Solimotion FTR16 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar S PMD75 Manuel

Endress+Hauser

Endress+Hauser Liquiline System CA80TP Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline Promass series Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquipoint T FTW31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Micropilot M FMR240 Instructions d'utilisation et d'installation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Acterna

Acterna MS1400 Manuel utilisateur

R&S

R&S ZPH Manuel utilisateur