Emerson SolaHD SPS Series Manuel utilisateur

Uninterruptible Power Supply

User Manual

SPS and SLN UPS Series

CONTENTS

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Important Safety Instructions . . . . . . . . . . . . . . 2

3.0 General Description . . . . . . . . . . . . . . . . . . . 3

4.0 System Block Diagrams . . . . . . . . . . . . . . . . . 5

5.0 Installation and Operation . . . . . . . . . . . . . . . 6

6.0 LED Diagnostics . . . . . . . . . . . . . . . . . . . . . 7

7.0 Troubleshooting . . . . . . . . . . . . . . . . . . . . 8

8.0 Technical Specifications . . . . . . . . . . . . . . . . . 9

Page: 1

What’s Included

The UPS is shipped with the following items:

• User manual

• USB cable: high speed 2.0 Standard Type A-B, 6 ft (1.8 m)

Note: UPSwatch - monitoring/diagnostic software is available by downloading at www.solahd.com

The software is compatible with Windows 7, 8, 10, Windows 2008, 2012, 2016,

Windows 2008/2012 Server Core, Hyper-V 2008/2012, Linux OpenSUSE 11.4,

Linux ubuntu 10.04, Linux Fedora 3.1.9, CentOS 5.8, Citrix XenServer 6.0.0, Linux KVM

Accessories (Optional)

• SLNSPSPMBRK: SLN600 and SPS850 Wall Mount Bracket

• SLNSPSPMBRK1: SLN1000 and SLN1500 Wall Mount Bracket

Introduction

This bracket allows the SLN and SPS UPS Series to be mounted to the

wall/panel. One bracket kit is required for each UPS. The hardware

necessary for mounting the bracket is supplied.

What’s Included

One (1) Metallic Wall Mounting Bracket

Four (4) Rubber Spacer Blocks

Four (4) Screws

One (1) Instruction Manual

Wall Mounting Instructions

1. Mount two (2) bottom screws 5 inches apart.

2. To prevent the UPS from sliding out of position, afx the four (4)

rubber spacer blocks to the side of the UPS, adjacent to the wall.

3. Place the bracket on the UPS as shown in Figure 1.

4. Push the bracket down onto the bottom screws and secure.

Figure 1

SLNSPSPMBRK or SLNSPSPMBRK1 Wall/Panel Mounting Bracket Kit

Part Number: A272-065 Rev. 7

While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages result-

ing from use of this information or for any errors or omissions. Specications are subject to change without notice. The Appleton and Emerson logos are registered in the U.S. Patent and

Trademark Ofce. All other product or service names are the property of their registered owners.

5. Secure the top of the bracket with the two (2) remaining screws.

Figure 2

6. Tighten all four (4) screws. Make sure the bracket and UPS are secure.

Figure 3

Technical Support

Phone: (800) 377-4384 option 2

E-mail: [email protected]

www.solahd.com

1.0 Introduction

Thank you for selecting the SPS or SLN Uninterruptible Power System. This manual contains important safety

instructions that should be followed during the installation and operation of your UPS.

• Please read all safety, installation and operating instructions before attempting to install or operate the UPS.

• Please adhere to all warnings on the unit and in this manual during installation and operation.

This UPS is designed for industrial or commercial use. The UPS features a compact design that ts into a

limited-space working environment.

This product features the following:

• High reliability.

• Auto restart during AC recovery.

• AC overload protection.

• Over temperature thermal protection.

• Battery overcharge protection.

• SLN models feature AVR (Auto Voltage Regulation).

• Input voltage out-of-range protection.

• Remote monitoring and control software via UPSwatch.

Page: 2

2.0 Important Safety Instructions

!WARNING - Risk of electric shock, fire and personal injury.

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed

during installation and maintenance of the UPS.

The UPS is intended for installation in a controlled environment.

Do not attempt to open the UPS. The UPS contains no user-serviceable parts.

• Install the UPS in an indoor temperature- and humidity-controlled environment, free of conductive

contaminants.

• Do not install the UPS in or near water.

• In order to avoid overheating the UPS, allow proper ventilation of the unit. Do not block or cover the top,

bottom or sides of the UPS.

• Do not expose the UPS to direct sunlight or install the unit near any heat sources.

• Install the UPS onto a level surface in an upright position. Do not place the UPS on an unstable surface

such as a cart, stand or table.

• The UPS must be installed near the socket receptacle so that the cord can be easily disconnected. To

properly turn off the UPS, press the OFF button, then disconnect the input power supply cord from the

AC power outlet.

• Connect the AC input power cord to a properly grounded AC supply source.

• Connect the UPS to a grounded supply circuit with proper branch circuit protection. Follow all applicable

National Electrical Codes®(NEC®) and Canadian Electrical Codes (CEC) as well as all local codes.

• Do not plug the UPS into a power strip. Do not daisy-chain one UPS power cord into another UPS output

receptacle. Do not place the UPS power cord where it may be damaged.

• Do not dispose of the UPS in a re as the battery may explode.

• Do not open or damage the battery. Released electrolyte is harmful to the skin and eyes and may be toxic.

• The batteries are not user or service replaceable. Do not attempt to open the unit to replace them.

• Turn off the UPS and disconnect the input cord from the AC power supply before cleaning. Do not use

liquid or aerosol cleaners. Use only a dry cloth on the exterior of the UPS. Do not open the unit.

• The UPS should not support laser printers or scanners, as the equipment may draw too much power,

potentially resulting in a UPS overload.

• This UPS is not for use in a computer room as dened in the Standard For the Fire Protection of

Information Technology Equipment, NFPA 75.

Page: 3

3.0 General Description

3.1 Front Panel - Models SLN600, SPS850, SLN1000, SLN1500

Power Switch

Red LED

Indicator

Green LED

Indicator

When the Green LED Indicator:

Shows a steady light, the UPS is in

AC Mode.

Is ashing, the UPS is in

Battery Mode.

For more details, refer to Section 6.0 LED Diagnostics.

3.2 Back Panel - Models SLN600, SPS850

Breaker

AC Input Cord

USB (B TYPE)

Output Receptacles

Page: 4

3.3 Back Panel - Model SLN1000

Breaker

AC Input Cord

USB (B TYPE)

Output Receptacles

3.4 Back Panel - Model SLN1500

Output Receptacles

Breaker

AC Input Cord

USB (B TYPE)

Page: 5

4.0 System Block Diagrams

SLN System Block Diagram

SPS System Block Diagram

Page: 6

5.0 Installation and Operation

5.1 Inspection

Remove the UPS from its packaging and inspect it for damage that may have occurred during shipping. If

shipping damage has occurred, repack the unit, and contact your local carrier and SolaHD

distributor immediately.

5.2 Placement

Install the UPS indoors in a protected environment that provides adequate airow around the unit, and is

free from excessive dust, moisture and contaminants. The UPS may be installed in an environment where the

ambient temperature is 0°–40°C.

5.3 Starting the UPS

To turn on/off the UPS, press the power switch for 3 seconds.

When the Green LED Indicator:

• Shows a steady light, the UPS is in AC Mode.

• Is ashing, the UPS is in Battery Mode.

5.4 Battery Charging

Plug AC input cord into utility power for at least eight (8) hours in order to fully charge the battery prior to use,

as some charge may have been lost during shipping. Unit does not need to be turned on in order for charging

to occur.

5.5 Load/Output Connection

Connect one device into each of the power receptacles supplied on the back of the UPS.

Catalog Number Dimensions in Inches (Millimeters)

H W D

SLN600 5.6 (142) 4.1 (104) 11.8 (300)

SPS850 5.6 (142) 4.1 (104) 11.8 (300)

SLN1000 7.1 (180) 5.1 (130) 12.6 (320)

SLN1500 7.1 (180) 5.1 (130) 12.6 (320)

Page: 7

6.0 LED Diagnostics

Green LED Red LED Alarm (Audible)* Status

ON OFF OFF Battery Fully Charged

ON OFF OFF AC Mode

Flashing every 5 seconds OFF 1 beep every 5 seconds Battery Mode

Flashing every 3 seconds OFF 1 beep every 3 seconds Battery Low Warning

Flashing every 1 second OFF OFF Standby Mode

OFF ON Continuous beep

every 1 minute for 1 hour Fault Alarm

OFF Flashing every 10 seconds 1 beep every 10 seconds Over Temperature

Flashing every 10 seconds OFF OFF Charging

OFF Flashing every 3 seconds

Continuous beep every

3 seconds until fault

is removed.

Output Short

Flashing every 3 seconds OFF OFF

Automatic Voltage

Regulation (AVR) Mode -

SLN Model Only

*NOTE: Push and release ON/OFF to silence or activate audible alarm.

Page: 8

7.0 Troubleshooting

Problem Possible Cause Solutions

The UPS does not turn on.

(No alarm, no display).

The UPS is not turned on. Press the ON/OFF Button for 3 seconds and release.

Battery fault. Contact Tech Support.

UPS fault. Contact Tech Support.

The UPS runs continually in battery mode. The power cord is not

connected properly.

Check the power cord to ensure it is

connected properly.

Battery runtime cannot be achieved.

Battery voltage is too low. Charge the battery (batteries) for at least

eight (8) hours.

Output overload.

Remove some loads. Before reconnecting

equipment, please verify that the load matches the

UPS capability shown in the specications.

Battery fault.

The UPS has been operating at high temperatures

that are not conducive to the battery. If the

battery is near the end of its life, please contact

Customer Support.

Charger fault or other reasons. Contact Tech Support.

The red LED is on and beeps. The UPS has overloaded. Please disconnect loads or check if the load is

shorted or malfunctioning.

Green LED ashes every 1 second with no

sound and no output voltage. Battery voltage is too low.

Please check if the AC is normal or the power cord is

disconnected. When the utility is normal, the UPS

will automatically restart and charge the battery.

The green and red LEDs are always on and

the audible alarm is silent. Charge circuit error. Contact Tech Support.

The red LED ashes, and the audible alarm

is silent. The UPS is overheated.

Check that the UPS has good ventilation and is not

in direct sunlight or near heat sources. Reduce the

output load.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson UPS

Emerson

Emerson 1000VA Manuel utilisateur

Emerson

Emerson Liebert APM 90 Manuel utilisateur

Emerson

Emerson Liebert NX Manuel utilisateur

Emerson

Emerson Liebert GXT3 Series Manuel utilisateur

Emerson

Emerson SOLAHD SDU DC UPS B Series Manuel utilisateur

Emerson

Emerson Liebert GXT4-5000RT230 Manuel utilisateur

Emerson

Emerson Liebert GXT3-3000RT120 Manuel utilisateur

Emerson

Emerson Liebert itON BX Manuel utilisateur

Emerson

Emerson Liebert NX300 Series Manuel utilisateur

Emerson

Emerson Liebert PowerSure PSA1000MT-120 Manuel utilisateur

Emerson

Emerson PSI-XR Manuel utilisateur

Emerson

Emerson Liebert HiPulse E Series Manuel d'utilisation et d'entretien

Emerson

Emerson Liebert FPC Manuel utilisateur

Emerson

Emerson Liebert GXT3 Series Manuel utilisateur

Emerson

Emerson SolaHD SDU AC B-Series Manuel utilisateur

Emerson

Emerson Liebert APS Manuel utilisateur

Emerson

Emerson Adapt Manuel utilisateur

Emerson

Emerson 500VA Manuel utilisateur

Emerson

Emerson Liebert GXT4-6000RT230 Manuel utilisateur

Emerson

Emerson NXr Manuel utilisateur

Emerson

Emerson SolaHD SDU AC B Series Manuel utilisateur

Emerson

Emerson Liebert GXT3 Series Manuel utilisateur

Emerson

Emerson Liebert GXT3 Series Manuel utilisateur

Emerson

Emerson Liebert NX 10-30kVA Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur