Emerson Liebert itON 1500 Manuel utilisateur

1 10H52200GM60 – Rev. 5 – 06/2014

Liebert®itON

Quick-Start Guide – 1500VA/2000VA, 230V

1BIMPORTANT SAFETY INSTRUCTIONS

Read SAFETY INSTRUCTIONS sheet first.

SETUP

4BStep 1

Inspect the Package

Inspect the package and the UPS upon receipt.

Notify the carrier and dealer of visible damage.

 

UPS Quick-start Safety Quick-start guide USB cable Input Cable

guide Instructions (all languages)

5BStep 2

Decide Where to Place the UPS

The UPS must be placed indoors, protected from

water, direct sunlight and excessive heat.

Provide at least 7.8” (20 cm) of clearance on all

sides of the unit for proper ventilation.

6BStep 3

Charge the UPS Battery Before Use

The UPS battery is fully charged before shipping.

However, some charge may be lost during shipping

and the battery should be recharged prior to use.

Plug in the AC input cord (supplied) to the wall

outlet. For the best results, suggest to charge

the battery at least 6 hours before initial use.

The unit charges its battery while connecting

to the utility.

7BStep 4

Start the UPS

After the battery is fully charged:

Turn on the UPS by pressing the On/Off

button.

LED1 should be illuminated (green), indicating the

UPS is operating in Normal mode.

8BStep 5

Connect the Loads

The UPS has six battery backup outlets that provide

power when the UPS operates on battery. (see

Figure 2 on next page)

Plug the loads into the battery backup outlets

on the rear of the UPS.

CAUTION: NEVER connects a laser printer or

scanner to the UPS unit. This may cause the damage

of the unit.

Step 6

Connect the Network Surge Protection

The UPS has two RJ-11 jacks for network lines.

Connect a single-line network cable into the

RJ-11 network surge protection IN jack on the

rear of the UPS.

Connect a RJ-11 cable from the OUT jack on

the rear panel of the UPS to a port on a PC or

network device such as a router.

Step 7

Set Up Shutdown Software

To start using shutdown software:

Install the shutdown software on supplied CD.

Follow on screen instructions to install the

software.

Connect one end of USB cable (supplied) to

the USB port on the rear panel of the UPS.

Connect the other end of USB cable on the

computer USB port.

See the software user manual for detailed

operation inside of supplied CD.



10H52200GM60 – Rev. 5 – 06/2014 2

10BUPS CONTROLS AND CONNECTIONS

Figures 1 – Front Panel LEDs



Figure 2 – Rear Panel

UPS Status, Alarm Conditions and Alerts

Condition LED Color Solid/Flashing Audible Alarm

Normal mode LED 1 Green Solid (none)

Battery mode LED 1 Green Flashes Every 10 seconds

Load level at Normal mode LED 3-6 Green Solid Overload: every 0.5 second

Battery level at Battery mode LED 3-6 Green Solid Low battery: every second

Fault LED 2 Red Solid Continuous until UPS shuts down

Battery replacement LED 2 Red Solid Every 2 seconds



9BTROUBLESHOOTING

If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, please contact your local

Emerson Network Power representative.

Problem Possible Causes Solutions

Utility is normal, but LED is not

illuminated.

Battery capacity may be low.

The UPS battery reached end of life.

The UPS may not be turned on.

Recharge the UPS at least 6 hours.

Properly trained and qualified service personnel

replace the battery with the same type of

battery ,do not attempt to replace the battery

yourself.

Press the On/Off button to turn on the UPS.

Alarm buzzer beeps continuously

although utility power is normal.

The UPS may be overloaded. Disconnect some equipment from the UPS.

UPS does not provide expected

backup time.

The UPS may be overloaded

Battery voltage may be low.

The UPS battery reached end of life.

Disconnect some equipment from the UPS.

Recharge the UPS at least 6 hours.

Properly trained and qualified service personnel

replace the battery with the same type of

battery ,do not attempt to replace the battery

yourself.

Utility is normal, but UPS status

LED flashes.

The power cord may not be

connected properly.

Connect the power cord securely into a wall outlet.



3BSPECIFICATIONS

Model Liebert itON 1500 Liebert itON 2000

Capacity (VA/W) 1500/900 2000/1200

Net Weight, lb. (kg) 24 (11.1) 25 (11.5)

Dimensions – W x D x H (mm) 146 x 391 x 205

Line Input Nominal Voltage 220 - 240VAC

Line Input Voltage Range ** 170 - 280VAC

Line Frequency 50Hz / 60Hz (auto sensing)

Output Voltage (Utility Power Normal) 230VAC

Output Voltage (Battery Operation) ±10%

On-Battery Wave Form Stepped sinewave

Battery Type – VDC x Ah x Quantity 12V x 9 Ah x 2 12V x 9 Ah x 2

Typical Recharge Time 4 hours to 90%

Battery Run Time* – Half Load 5 minutes 3 min 10 Sec

Operating Temperature, °F (°C) 32 to 104 (0 to 40)

Storage Temperature, °F (°C) -4 to 122 (-20 to 50)

Operating /Storage Relative Humidity 0 – 90%, non-condensing



*Battery run time may vary depending on load. ** Depending of output load.

Emerson and Business-Critical Continuity are trademarks of Emerson Electric Co. or one of its affiliated companies.

Battery backup

outlets

(3 x IEC C13)

LED 1

(status)

LED 3-6

(

Load/Batter

level

)

On/Off button

LED 2 (fault)

USB interface

Battery backup

outlets

(3 x Schuko)

AC mains inlet

& fuse

RJ-11 jacks (2)

Network surge

protection

Ce manuel convient aux modèles suivants

Autres manuels Emerson UPS

Emerson

Emerson Liebert GXT3-3000RT120 Manuel utilisateur

Emerson

Emerson Liebert GXT2-700RT230 Manuel d'instructions

Emerson

Emerson Liebert itON 1500VA Manuel utilisateur

Emerson

Emerson Liebert NXC 10-20kVA Manuel d'instructions

Emerson

Emerson Liebert GXT4-5000RT230 Manuel utilisateur

Emerson

Emerson Liebert APM 15-90kVA Manuel utilisateur

Emerson

Emerson Liebert GXT-MT Manuel utilisateur

Emerson

Emerson PSI-XR Manuel utilisateur

Emerson

Emerson Adapt Manuel utilisateur

Emerson

Emerson Liebert GXT3 Series Manuel utilisateur

Emerson

Emerson Liebert NXL Manuel utilisateur

Emerson

Emerson SolaHD SDU DC UPS B Series Manuel utilisateur

Emerson

Emerson Liebert Series 610 Manuel

Emerson

Emerson Liebert eXM Manuel utilisateur

Emerson

Emerson SOLAHD SDU DC UPS B Series Manuel utilisateur

Emerson

Emerson Liebert NXL Manuel utilisateur

Emerson

Emerson 10 kVA Manuel utilisateur

Emerson

Emerson SolaHD SDUMBUSCARD Manuel utilisateur

Emerson

Emerson Liebert PowerSure PSP Manuel utilisateur

Emerson

Emerson Liebert NXL Manuel utilisateur

Emerson

Emerson Liebert NXL Manuel utilisateur

Emerson

Emerson Liebert UPStation GXT2U Manuel utilisateur

Emerson

Emerson NXr Manuel utilisateur

Emerson

Emerson Series 610 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur