Emerson Appleton EHLED Manuel utilisateur
Appleton • 1.800.621.1506 • www.appletonelec.com DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 1 of 16
DOC00038A000 INSTRUCTION SHEET
Installation and Maintenance Instructions for Appleton™ EHLED
Portable Handlamp
IMPORTANT: RETAIN THIS INSTRUCTION SHEET FOR FUTURE REFERENCE. For safe installation
and operation, please read these instructions carefully and with full understanding.
• This luminaire is designed for use in Class I, Div. 1, Groups C & D and Type 4X locations.
Product Safety
Signal Words Defined
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING
indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a
hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices
not related to physical injury.
Safety Instructions
WARNING:
•DO NOT OPEN FIXTURE WHILE IT IS ENERGIZED.
•DO NOT USE FIXTURE ON UN-GROUNDED CIRCUITS. Failure to ground this luminaire can result in an
electrical shock which may be fatal.
CAUTION:
•ELECTRIC SHOCK HAZARD: Disconnect from power (unplug) before re-lamping or servicing.
•Take note of caution labels on product.
•Inspect cord regularly for damage and replace if nexessary for user safety.
•Do not submerge any part of product in liquids.
•Do not hang xture by its electrical cord. Use manufacturer's hooks or mounting brackets.
•Take care not to drop xture as damage to the product may result.
•Power supply cord is UL Listed and meets OSHA requirements for grounding of hand-held tools.
APPLETON™ EHLED PORTABLE HANDLAMP
Appleton • 1.800.621.1506 • www.appletonelec.com DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 2 of 16
Product Features - Refer to Figure 1
A. Dimensions The overall length is 20" (508mm). Outside diameter is 4-7/8" (124mm).
B. Guard The guard is made of non-sparking cast aluminum.
C. Hook The non-sparking metal hook is located on the outer end of the guard.
The hook shall swivel and t over a 3/4" (19mm) pipe.
D. Globe The globe is made of high-impact, heat-resistant, tempered clear glass.
E. Lamp Acceptable wattage for bulbs/lamps are 75W or 100W (depending on handlamp model).
F. Lamp Socket The lamp socket is designed to accomodate a standard E27 incandescent bulb.
G. Phenolic Handle The handle is made from chemical-resistant phenolic resin.
H. Power Cord
Flexible SO-type (or similiar) cord rated at 600 volts. 16/3 or 14/3 conductors.
The plug, if provid ed, shall be listed for use in at least Class I, Groups C and D Hazardous Locations
and suitable for use with the above cords having a grounding conductor.
I. Nameplate The UL label includes listing information and relamping instructions.
FIGURE 1: EHLED PRODUCT FEATURES
A
B
C
D
E
F
G
H
I
Appleton • 1.800.621.1506 • www.appletonelec.com DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 3 of 16
Operating Instructions
A. Locate a power source to be used for the handlamp. The EHLED is rated for 120–277 V AC 50/60Hz.
NOTE: If the power source is WITHIN a Hazardous Location the handlamp must be connected to the power source
with explosion proof ttings suitable for the Hazardous Location. If the handlamp is provided with an explosion proof
connector, the power source outlet must also meet the requirements of the Hazardous Location. If the handlamp is to
be connected to a power source OUTSIDE of the Hazardous Location, it may have a NEMA 5-15P or other connector
suitable for the type of connection.
B. Connect the handlamp to the power source.
NOTE: Always use a grounded outlet.
C. Position handlamp for use.
D. Disconnect power cord from power source to discontinue use. (The handlamp is switch-less.)
Troubleshooting
CAUTION: ELECTRIC SHOCK HAZARD: DISCONNECT handlamp from power source and remove to a safe area
(beyond the hazardous operating environment) before inspection or repair work is attempted.
Failure of the handlamp to operate could result from a break in the power circuit or failure of a component. In this case, the handlamp
is not operational, DO NOT operate.
1. With an Ohmmeter, verify that supply voltage is correct (120±5VAC or 12±2VDC, depending on model).
2. Check for short to ground. Using a Volt-Ohm Meter set on its lowest Ohm scale, rmly touch one lead to one blade of the
plug while rmly touching the other lead to the ground pin on the plug. An open circuit reading (innite Ohms) should be
observed. Repeat this process for the other plug blade. If a short exists, DO NOT operate the handlamp.
3. Replace lamp by following lamp replacement instructions.
Maintenance/Inspection
1. Check for any cracks on globe or guard. If any cracks/damage are seen, order replacement part EHLEDTKG Globe & Guard
Assembly which also contains
2. If nicks, cracks, or pitting are seen in the handle, DO NOT USE, purchase a new handlamp.
3. If the lamp socket shows signs of arcing, burning, corrosion, moisture or other damage, DO NOT USE, purchase a new handlamp.
4. If there is any damage to, or punctures seen on the power cord, DO NOT USE, purchase a new handlamp.
DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 4 of 16
Appleton • 1.800.621.1506 • www.appletonelec.com
Globe & Guard Assembly or Lamp Replacement Instructions
First, be sure that you have all the parts necessary for your replacement project on hand before beginning this process. Reference the
table below to order the replacement parts you'll need.
Part No. Description
EHLEDTKG Guard & Globe Assembly PLUS the Tool Kit (Tool Kit contains a Guard Housing Jig and Wrench Tool.
See Figures 2 and 3.)
EHLEDTK Tool Kit (Contains a Guard Housing Jig and Wrench Tool. See Figures 2 and 3.)
EHLEDTKB LED Lamp AND Tool Kit (Tool Kit contains a Guard Housing Jig and Wrench Tool. See Figures 2 and 3.)
FIGURE 2: GUARD HOUSING JIG
FIGURE 3: WRENCH TOOL
DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 5 of 16
Globe & Guard Assembly or Lamp Replacement Instructions (Continued)
CAUTION: ELECTRIC SHOCK HAZARD: DISCONNECT handlamp from power source and remove to a safe area
(beyond the hazardous operating environment) before inspection or repair work is attempted.
NOTE: When performing the following replacement steps, avoid letting any liquid enter the handle. Ensure that the inside
of the globe and handle are completely dry of ALL liquids before reassembling the handlamp.
1. Unplug the handlamp from power source and make sure to remove it to a safe area beyond the hazardous operating environment.
Then, use an Allen wrench (hex key) to loosen the set screw on the lower edge of the guard.
FIGURE 4: LOOSEN THE EHLED'S SET SCREW
2. Insert the Guard Housing Jig into a bench vise and tighten the vise onto the jig.
FIGURE 5: GUARD HOUSING JIG TIGHTENED INTO BENCH VISE
Appleton • 1.800.621.1506 • www.appletonelec.com
DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 6 of 16
Globe & Guard Assembly or Lamp Replacement Instructions (Continued)
3. Ensure that the EHLED handlamp is unplugged, then place into the jig as shown below.
FIGURE 6: EHLED HANDLAMP INSERTED INTO JIG
4. With the handlamp guard seated rmly in the Guard Housing Jig, use the Wrench Tool to rotate the handlamp's handle
COUNTER-CLOCKWISE until the handle separates from the handlamp guard.
FIGURE 7: TURN THE WRENCH TOOL COUNTER-CLOCKWISE TO REMOVE HANDLE
Appleton • 1.800.621.1506 • www.appletonelec.com
DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 7 of 16
Globe & Guard Assembly or Lamp Replacement Instructions (Continued)
5. Hand pressure along may not provide enough torque to unseat the handlamp's handle. If necessary, use a 3/4" socket wrench,
as shown below, to provide additional leverage to unseat the handle. Do NOT use a hammer or other striking tool to apply impact
force to the Wrench Tool as this may cause damage to the handle of the handlamp.
FIGURE 8: USING A 3/4" SOCKET WRENCH TO UNSEAT THE HANDLE
6. Once the handle is unseated from the Guard & Globe Assembly, install a new Guard & Globe Assembly and lamp. The Guard
& Globe Assembly plus the installation tools are provided in the EHLEDTKG replacement kit. A new lamp is available in the
EHLEDTKB replacement kit. Installation tools to complete this project are also included in this kit. Install the replacement lamp into
the socket on the handle.
FIGURE 9: HANDLAMP WITH REPLACEMENT LAMP INSTALLED
7. Thoroughly clean the Guard & Globe Assembly, external threads and top mating surface of the handle with a clean cloth. Make sure
liquid DOES NOT enter the handle.
Appleton • 1.800.621.1506 • www.appletonelec.com
DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 8 of 16
Globe & Guard or Lamp Replacement Instructions (Continued)
8. Insert the handle into the Guard Housing Jig. Screw the Guard & Globe Assembly CLOCKWISE onto the handle using the Wrench
Tool. Use 30 ft. lbs. torque.
FIGURE 10: TURN THE WRENCH TOOL CLOCKWISE TO ATTACH HANDLE
EHLED Portable Handlamp and Replacement Parts
Part No. Description
EHLED Portable Handlamp
EHLEDTKG Guard & Globe Assembly PLUS the Tool Kit (Tool Kit contains a Guard Housing Jig and Wrench Tool.
See Figures 2 and 3.)
EHLEDTK Tool Kit (Contains a Guard Housing Jig and Wrench Tool. See Figures 2 and 3.)
EHLEDTKB LED Lamp AND Tool Kit (Tool Kit contains a Guard Housing Jig and Wrench Tool. See Figures 2 and 3.)
Except as expressly provided by Appleton Grp, LLC (Appleton), Appleton products are intended for ultimate purchase by industrial users and for operation by persons trained and experienced in the use and maintenance of this equipment
and not for consumers or consumer use. Appleton warranties DO NOT extend to, and no reseller is authorized to extend Appleton’s warranties to any consumer.
While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or
omissions. Specications are subject to change without notice. The Appleton and Emerson logos are registered in the U.S. Patent and Trademark Ofce. All other product or service names are the property of their registered owners.
©2020 Appleton Grp, LLC. All rights reserved.
Appleton • 1.800.621.1506 • www.appletonelec.com DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 9 of 16
DOC00038A000 INSTRUCTION SHEET
Instructions d’installation et d’entretien de la baladeuse
Appleton™EHLED
IMPORTANT: CONSERVER CETTE FICHE D’INSTRUCTIONS POUR RÉFÉRENCE. Pour une installation et
un fonctionnement en toute sécurité, lire attentivement les présentes instructions et s’assurer de les
avoir bien comprises.
• Ce luminaire est conçu pour une utilisation dans les zones de classe I, div. 1, groupes C et D, et type 4X.
Sécurité du produit
Définitions des termes d’avertissement
Le terme DANGER indique une situation dangereuse qui, si elle n’est pas évitée, provoquera des blessures graves,
voire mortelles. Le terme AVERTISSEMENT indique une situation dangereuse qui, si elle n’est pas évitée, est
susceptible de provoquer des blessures graves, voire mortelles. Le terme MISE EN GARDE indique une situation
dangereuse qui, si elle n’est pas évitée, est susceptible de provoquer des blessures légères ou modérées. Le terme
AVIS est utilisé pour traiter des pratiques qui ne sont pas liées à des blessures physiques.
Consignes de sécurité
AVERTISSEMENT:
•NE PAS OUVRIR LE LUMINAIRE LORSQU’IL EST SOUS TENSION.
•NE PAS UTILISER LE LUMINAIRE SUR DES CIRCUITS NON MIS À LA TERRE. L’absence de mise à la terre
de ce luminaire peut entraîner un choc électrique susceptible d’être fatal.
MISE EN GARDE:
•RISQUE DE CHOC ÉLECTRIQUE : couper l’alimentation (débrancher) avant de remplacer l’ampoule ou d’effectuer
l’entretien.
• Tenir compte des étiquettes de mise en garde apposées sur le produit.
• Inspecter régulièrement le cordon pour détecter tout dommage et le remplacer si nécessaire pour la sécurité de l’utilisateur.
• N’immerger aucune partie du produit dans des liquides.
• Ne pas suspendre le luminaire par le cordon d’alimentation. Utiliser les crochets ou les équerres de xation du fabricant.
• Veiller à ne pas faire tomber le luminaire pour éviter de l’endommager.
• Le cordon d’alimentation est homologué UL et répond aux exigences de l’OSHA relatives à la mise à la terre
des outils portatifs.
BALADEUSE APPLETON™EHLED
Appleton • 1.800.621.1506 • www.appletonelec.com DOC00038A000 Rev. 00 02/13/20 MY6381 • Page 10 of 16
Présentation du produit – Voir la Figure1
A. Dimensions La longueur hors tout est de 508mm. Le diamètre extérieur est de 124mm.
B. Grille de protection La grille de protection est composée d’aluminium moulé antiétincelant.
C. Crochet Le crochet métallique antiétincelant se trouve à l’extrémité extérieure de la grille de protection.
Il pivote et convient aux conduites de 19mm.
D. Globe Le globe est en verre trempé transparent résistant aux chocs et à la chaleur.
E. Ampoule La puissance électrique acceptable pour les ampoules est de 75W ou 100W (selon le modèle
debaladeuse).
F. Douille La douille de l’ampoule est conçue pour une ampoule à incandescence standardE27.
G. Manche en résine
phénolique Le manche est composé de résine phénolique résistante aux produits chimiques.
H. Cordon
d’alimentation
Le cordon exible de type SO (ou similaire) est homologué pour une tension de 600V.
Conducteurs16/3 ou 14/3.
Si elle est fournie, la che doit être homologuée pour une utilisation dans les zones dangereuses
declasseI, groupesC et D minimum, et convenir à une utilisation avec les cordons ci-dessus
équipés d’un conducteur de mise à la terre.
I. Plaque signalétique L’étiquette UL comprend les informations d’homologation et les instructions de remplacement
del’ampoule.
FIGURE1: PRÉSENTATION DE LA BALADEUSE EHLED
A
B
C
D
E
F
G
H
I
Table des matières
Langues :
Manuels Éclairage extérieur populaires d'autres marques
Lindby
Lindby 9949029 Manuel utilisateur
HEPER
HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation
HEPER
HEPER LW8034.003-US Instructions d'installation et d'utilisation
Maretti
Maretti VIBE S 14.6080.04.A Manuel utilisateur
BEGA
BEGA 84 253 Manuel
HEPER
HEPER MINIMO Instructions d'installation et d'utilisation
LIGMAN
LIGMAN BAMBOO 3 Manuel utilisateur
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur
urban ambiance
urban ambiance UQL1273 Manuel utilisateur
TotalPond
TotalPond 52238 Manuel utilisateur
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuel utilisateur