Emerson E2 Manuel utilisateur
quick start guide
Document Part # 026-4922 Rev 0 29-JUN-2012
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
E2 Setup with Veeder-Root TLS-350
MODBUS Device for 527-0370
This document will guide you through setting up and commissioning the Veeder-Root
TLS-350 (Automatic Tank Gauging System) MODBUS Device in the E2 controller.
STEP 1: Upload the description file to the E2 controller.
1. From UltraSite, connect to your E2 controller.
2. Right-click the E2 icon and select Description File Upload.
3. Browse to the location of the description file and click Upload.
4. After uploading, you will need to reboot the E2 controller.
Note that this device requires E2 firmware version 3.01 or higher.
Figure 1 - Description File Upload
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 2 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 2: Activate the license of the device.
5. From the E2 front panel (or via the Terminal Mode), press , (System Configura-
tion), and (Licensing).
6. Press F1 (ADD FEATURE) and enter your license key.
STEP 3: Terminate the RS485 communication cable.
7. Connect the DB-9 Pin Serial Communication Cable Plug (3)TXD + and (4)TXD —
as shown in Figure 3.
8. Ensure that communication polarity is reversed when connecting to the E2.
Figure 2 - Add License Screen
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 3 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
STEP 4: Configure the MODBUS serial port.
9. From the E2 front panel (or via Terminal Mode), select , , , then toggle the
F2 key to C3: Serial tab and set up as shown.
Dual Serial Gateway
Field Server
FS-B2510
Serial
Port-1 Serial
Port-2
Model
TL-350
Veeder-Root
Panel
RS-485
Network
Device
5
+
+
Shield
Phoenix
Plugin
DB-9 Pin
Plug
E2
Controller
Two Wire (1/2 duplex)
DB-9 Pin Plug RS-485
Device
Signal Pin Signal
TXD+ 3 RXD+
TXD- 4 RXD-
RXD+ 1 TXD+
RXD- 2 TXD-
RTS+ 7
RTS- 9
CTS+ 8
CTS- 6
GND 5 GND
Figure 3 - Wiring Diagram to RS485 Network Cable
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 4 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
•COM4Connection:MODBUS-1
•COM4Baud:9600 baud
•COM4DataSize:8
•COM4Parity:None
• COM4 Stop Bits: 1
STEP 5: Once the license is activated, add the device to the E2 controller.
10. Press , (System Configuration), (Network Setup), (Connected I/O Boards &
Controllers).
11. Press F2 (NEXT TAB) to go to C4: Third Party tab. You should see the device in the list.
Enter the number of devices to add and press the button to save your changes.
Figure 4 - MODBUS Port Serial Configuration
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 5 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
KEY POINTS:
• The FieldServer FS-B2510 is a Gateway Protocol Translator that enables data transfer
between the E2 controller and the Veeder-Root TLS-350.
• RS485 Network Cable used -> (BELDEN 8641-24 AWG 2 Conductor Shielded Cable) or
equivalent.
STEP 6: Commission the device.
12. Press , (System Configuration), (Network Setup), (Network Summary).
13. Press F4 (COMMISSION) and select the MODBUS port that you will be assigning the
device to and then select the MODBUS device address.
Figure 5 - Adding the Device to the E2 Controller
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 6 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Figure 6 - Commissioning the Device
Figure 7 - MODBUS Port Assignment
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 7 of 8
©2012 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
quick start guide
Once the MODBUS Physical Address is commissioned, this window will appear:
After the MODBUS Port Address has been initiated, the Network Summary window will
appear (Figure 9).
Figure 8 - MODBUS Physical Address Commissioned
Figure 9 - Network Summary Screen
E2 Setup with Veeder-Root TLS-350 MODBUS Device for 527-0370
Document Part # 026-4922 Rev 0 29-JUN-2012 Page 8 of 8
This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or
their use or applicability. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice.
Emerson does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.
026-4922 29-JUN-2012 Emerson is a trademark of Emerson Electric Co. ©2012 Emerson Climate Technologies Retail Solutions, Inc. All rights reserved.
quick start guide
Once the device is online, it will display the status screen as shown:
Figure 10 - Status Screen
Autres manuels pour E2
15
Table des matières
Autres manuels Emerson Contrôleurs
Emerson
Emerson Fisher CS400 Series Manuel utilisateur
Emerson
Emerson Bettis BHH Series Manuel utilisateur
Emerson
Emerson Fisher 1301 Series Manuel utilisateur
Emerson
Emerson Bettis Q series Manuel utilisateur
Emerson
Emerson Fisher S202 Manuel utilisateur
Emerson
Emerson S402Y Manuel utilisateur
Emerson
Emerson EXD-TEVI Manuel utilisateur
Emerson
Emerson KEYSTONE FIGURE 79U Manuel
Emerson
Emerson A36 Manuel
Emerson
Emerson ROC809 Manuel utilisateur
Emerson
Emerson AVENTICS 651 Series Manuel utilisateur
Emerson
Emerson E300 Series Manuel utilisateur
Emerson
Emerson FISHER 66 Manuel utilisateur
Emerson
Emerson Bristol ControlWave LP Manuel d'utilisation
Emerson
Emerson Affinity Manuel utilisateur
Emerson
Emerson Fisher 67C Series Manuel utilisateur
Emerson
Emerson CSB600 Series Manuel utilisateur
Emerson
Emerson Fisher 667 30 Manuel utilisateur
Emerson
Emerson Dixell XM670K Schéma de câblage
Emerson
Emerson Fisher 627 Series Manuel utilisateur
