Emerson XJ200 Manuel utilisateur

technical bulletin

Document Part # 026-4833 Rev 0 26-FEB-2013

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

XJ200 Installation and Operating Instructions

General Description

The XJ200 wireless communication modules are radio communication systems for con-

trolling and supervising units. The XJ200 consists of the XJ200 radio module P/N 318-5050

and its power supply PW-200J P/N 318-5051.

The XJ200 can cover a variety of functions within the monitoring network:

•Master: when it is connected to the X-WEB or E2 monitoring system.

•Slave/Repeater: when it is connected to the subnets of devices equipped with RS485.

•Repeater: when it is assigned the function as a simple bridge towards other subnets

that cannot be reached directly by the master.

The XJ200 modules enable 2-way communication between Dixell devices/modules

equipped with an RS485 output that are appropriately connected to each other and the X-

WEB or E2 unit, thereby replacing the connection via an RS485 cable.

Up to 15 devices can be connected to the same XJ200 (communication between the module

and the devices is via RS485), thereby covering several workstations with the same commu-

nication module. Up to 30 XJ200 modules can be connected to one (1) master XJ200.

The maximum distance possible between the XJ200 modules in an open space (with no

obstacles) is 200 meters (656 feet approx.). This distance can be remarkably reduced in the

presence of interference such as radio emitters, generators of electrical or magnetic fields or

solid objects that can affect the proper communication between the XJ200 modules.

The range of serial addresses allowed on the instruments connected to the XJ200 modules is

from 1 to 244.

Note that in order to work with the XJ200 modules, the instruments must be equipped with

an RS485 serial port and use MODBUS-RTU communication protocol.

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 2 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

General Warnings and Safety Precautions

Front Panel LEDs

The XJ200 module has three LEDs on the front panel:

POWER Green - Flashing with a frequency of 1 Hz: the module is ON and running

RS485 Yellow - Data is being transmitted/received via RS485 by the module

RADIO Green - The module is transmitting via radio

CAUTION! Read the following precautions before using this manual:

•This bulletin forms an integral part of the product and must be kept near the device for quick

and easy reference.

•The device must not be used for purposes other than those described below and particularly, it

cannot be used as a safety device.

•Verify the limits of application before proceeding.

SAFETY PRECAUTIONS

•Verify that the connections comply with the instructions in this manual before connecting the

device.

•Do not expose the unit to water or humidity: use the device only within the stipulated working

limits, avoiding sudden changes in temperature and high atmospheric humidity in order to pre-

vent condensation from forming.

•Caution: disconnect the electrical connections of the device before any maintenance.

•The module must never be opened.

•If the device is faulty or malfunctions, return it to the retailer or refer to the return address with

a precise description of the fault.

Figure 1 - XJ200

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 3 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

Installation and Assembly

Package Contents

Each XJ200 package contains the following components:

1. XJ200 radio device

2. Two self-tapping screws 3.9x6.5T to mount the XJ200 to the fixing bracket

3. Wall fixing bracket

4. Instruction manual

XJ200 Required Tools for Mounting

Mounting Directly

Parts required for assembly (not supplied)

Figure 2 - XJ200 Package Contents

Figure 3 - Parts Required For Assembly

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 4 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

1. To fix the module directly to the wall, use Figure 4 as a guide to make the two holes “B” at

the distance indicated in Figure 4.

2. Insert the dowels and mount the screws with a maximum

distance of 8 mm from the head to the wall.

3. Fix the XJ200 to the head of the screws by rotating the con-

tainer appropriately.

Fixing with the Use of Bracket

A suitable fastening bracket is included in every package to be used to:

• shelf mounting

• pipe mount fitting with appropriate retaining clamps (not supplied)

• wall mounting

As shown in the following pictures:

Figure 4 - Dimensions (not to scale)

CAUTION!

Set the XJ200 in the desired place in a VERTICAL POSITION.

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 5 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

Avoid horizontal or slanting positions.

Parts required for assembly (not supplied)

1. Mount the XJ200 to the fixing bracket using the two screws in the package.

2. The two screws are to be entered in holes “A” as shown in Figure 4.

3. The bracket can be bent and fixed so that the XJ200 is installed in a vertical position.

Recommendations for Proper Installations

• If possible, place the module high up in order to guarantee enhanced data transmission

or reception.

• If possible, avoid intermediate obstacles such as barriers, walls, floors and counters

between the modules.

• If necessary, pass through the obstacle using the cable and install the module on the

opposite side in order to have it in direct view with the master module connected to

the X-WEB or E2.

• The maximum distance possible between the XJ200 modules in an open space (with no

obstacles) is 200 meters (656 feet approx.).

• If the installation spans over a number of floors, try to position all the modules on the

same floor and connect the devices via cable in order to prevent communication prob-

lems due to obstacles caused by the floor or ceiling.

Figure 5 - Correct Mounting Positions

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 6 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

• The allowed temperature range for correct functioning is between 0°C and 60°C (32°F

to 140°F). Avoid places subject to heavy vibrations, corrosive gas, excessive filth, or

humidity.

Connections

Each module is supplied complete with a 1.5 meter

(4.9 feet approx.) cable to connect the serial com-

munication line and the power line.

The XJ200 is powered by 5V supplied by the PW-

200J power supply. The PW-200J requires 24VAC

supply voltage input.

X-WEB - XJ200 Master Connection

Set the XJ200 to Master

The XJ200 connected to the X-WEB must be configured as master.

1. Remove the cover of the XJ200.

Figure 6 - XJ200 with Cable

Figure 7 - PW-200J Power Supply

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 7 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

2. Close the jumper found inside the XJ200 by inserting the micro switch as shown in the

picture below.

3. Close the cover of the XJ200 once again.

4. Connect the XJ200, PW200J and the X-WEB as shown in the connection diagram below.

NOTE: When using the XJ200 with an XR, XM, or XEV controller, the XJ200 external power supply

must be used.

Figure 8 - Micro Switch

Figure 9 - XJ200 and X-WEB Connection

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 8 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

XJ200 and X-WEB Connection

Remove the Phoenix-style connector (supplied with the PW-200J) and use as a junction for

the RS485 line. The connection between the XJ200 and X-WEB is then implemented as fol-

lows:

1. Connect the GREEN wire of the XJ200 to the RS485 “+” terminal of the X-WEB.

2. Connect the PINK wire of the XJ200 to the RS485 “-” terminal of the X-WEB.

3. Power the X-WEB and the PW200J once again.

XJ200 Connection and Devices Equipped with a Serial Output

XJ200 and PW-200J Connection

1. Connect the white 5-pin connector to the “+5V supply” 5-pin connector of the PW-200J.

2. Connect the other devices to the RS485 serial line in compliance with the polarity.

3. Remove the Phoenix-style connector (supplied with the PW-200J) and use as a junction

for the RS485 line with the XJ200 as follows:

• Connect the GREEN wire of the XJ200 to the RS485 “+” terminal.

• Connect the PINK wire of the XJ200 to the RS485 “-” terminal.

Figure 10 - XJ200 and PW-200J Connection

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 9 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

Device Equipped with a TTL Serial Output

Device with TTL Output but Not Capable of Powering the XJ200. Example Ranges: Prime

CX, Wing Basic New, XC400C and XC600C

XJ200 and PW-200J Connection

1. Connect the GREEN wire to the RS485 “+” terminal of the PW-200J.

2. Connect the PINK wire to the RS485 “-” terminal of the PW-200J.

3. Connect the white connector to the “+5V supply” connector of the PW-200J.

Controller Connection with TTL and PW-200J

1. Connect the other devices to the RS485 serial line in compliance with the polarity.

2. Connect the two TTL outputs of the PW-200J and the device.

3. Then connect the RS485 line to the PW-200J, in compliance with the polarity.

Figure 11 - XJ200 with TTL and PW-200J Connection

XJ200 Installation and Operating Instructions

Document Part # 026-4833 Rev 0 26-FEB-2013 Page 10 of 17

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

technical bulletin

E2 and XJ200 Networking

XJ200 Wireless New Installation Procedure

E2-XJ200 Master Connection

In the new installation, you need to find a location in the store that has a direct line of sight

with at least one or two wireless modules (slave modules) on the sales floor. If the system

performs up to four hops, those in the indirect view can find their way to the master wireless

module location to them.

From the designated position, run a communication cable (three conductors) and wiring to

handle 24VAC, and depending on the distance, the wire gauge needs to be calculated. The

master module needs a power supply that takes 24 VAC and powers the wireless module

with 5VDC.

Figure 12 - XJ200 Wireless

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Unité de contrôle

Emerson

Emerson KTM VIRGO E Series Manuel

Emerson

Emerson KEYSTONE V30 Series Manuel utilisateur

Emerson

Emerson White-Rodgers 36C01 Manuel utilisateur

Emerson

Emerson Alco Controls 110RB Manuel utilisateur

Emerson

Emerson Fisher DSV1000 Manuel utilisateur

Emerson

Emerson Fisher EZ easy-e Manuel utilisateur

Emerson

Emerson ALCO Thermo TX6 Manuel utilisateur

Emerson

Emerson Rosemount ET410 Manuel utilisateur

Emerson

Emerson EX4 Manuel utilisateur

Emerson

Emerson Numatics DeviceLogix G2-2 Series Manuel d'instructions

Emerson

Emerson Sempell series Manuel utilisateur

Emerson

Emerson Fisher Baumann 24000F Manuel utilisateur

Emerson

Emerson Fisher HS Manuel utilisateur

Emerson

Emerson Fisher D3 Manuel utilisateur

Emerson

Emerson Fisher A11 Manuel utilisateur

Emerson

Emerson Fisher POSI-SEAL A31A Manuel utilisateur

Emerson

Emerson 903 Manuel utilisateur

Emerson

Emerson AVENTICS 501 Series Manuel utilisateur

Emerson

Emerson CROSBY Mode d’emploi

Emerson

Emerson FISHER NotchFlo DST Manuel utilisateur

Emerson

Emerson MVME7616E Guide de démarrage rapide

Emerson

Emerson YARWAY 60Y Series Manuel utilisateur

Emerson

Emerson Fisher 1805P Series Manuel utilisateur

Emerson

Emerson KEYSTONE V30 Series Manuel du propriétaire

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur