Elsys ERS Eye Manuel utilisateur

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Specifications in this document are subject to change without notice.

©Elektroniksystem i Umeå AB 2021

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual may be

dangerous or cause a violation of the law. The manufacturer, Elektroniksystem i

Umeå AB will not be held responsible for any loss or damage resulting from not

following the instructions of this operating manual.

•The device must not be dismantled or modified in any way.

•The device is only intended for indoor use. Do not expose it to moisture.

•The device is not intended to be used as a reference sensor, and

Elektroniksystem i Umeå AB will not be held liable for any damage which

may result from inaccurate readings.

•The battery should be removed from the device if it is not to be used for

an extended period. Otherwise, the battery might leak and damage

the equipment. Never leave a discharged battery in the battery

compartment.

•The device must never be subjected to shocks or impacts.

•To clean the device, wipe with a soft moistened cloth. Use another soft,

dry cloth to wipe dry. Do not use any detergent or alcohol to clean the

device.

Disposal note in accordance with ElektroG and WEEE Directive

2012/19/EU

The device, as well as all the individual parts, must not be disposed of

with household waste or industrial waste. You are obliged to dispose of the

device at the end of its service life in accordance with the requirements of

ElektroG in order to protect the environment and to reduce waste through

recycling. For additional information and how to carry out disposal, please

contact the certified disposal service providers. The sensors contain a lithium

battery, which must be disposed of separately.

 
3 
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden 
E-mail: suppo[email protected] ǀWeb: www.elsys.se 
Contents 
 
Important safety information.......................................................................................................... 2 
Description......................................................................................................................................... 4 
Main features of ERS Eye............................................................................................................................. 5 
Installation.......................................................................................................................................... 6 
Service and maintenance................................................................................................................ 7 
Sensor configuration........................................................................................................................ 8 
NFC Configuration.......................................................................................................................................... 8 
Over the air configuration............................................................................................................................. 9 
Application parameters ................................................................................................................................. 9 
Sensor behavior................................................................................................................................ 9 
NFC Read / Write........................................................................................................................................... 9 
Sensor startup ..............................................................................................................................................10 
Sampling mode / Periodic measurement................................................................................................11 
Schedule Transmission ...............................................................................................................................11 
Motion detection range...............................................................................................................................12 
PIR Lens detection pattern ........................................................................................................................12 
Traffic light LED............................................................................................................................................13 
Grid-Eye..........................................................................................................................................................14 
Specifications ..................................................................................................................................16 
Sensor payload format................................................................................................................................16 
Regulations......................................................................................................................................17 
Legal Notices ................................................................................................................................................17 
Federal Communication Commission Interference Statement............................................................17 
Declaration of conformity ...........................................................................................................................18 
 

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Description

ERS Eye is an advanced room occupancy and indoor climate sensor for

LoRaWAN® wireless network. The sensor measures temperature, humidity, light

intensity, and detects occupancy. It can detect occupancy based on body heat,

not only by movement. ERS Eye is a battery-powered device and is designed to

be mounted on the ceiling. It is equipped with NFC (Near Field Communication)

and can easily be configured from a smartphone.

The barcode contains DevEUI and sensor type. This label is located at the back

of your device,

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Main features of ERS Eye

•Compatible with LoRaWAN® specification 1.0.3

•Measures ambient temperature

•Measures ambient humidity

•Measures light intensity

•Detects motion using a passive IR sensor

•Detects occupancy using a Grid-Eye infra-red sensor

•Can detect occupancy even if people are sitting/standing still

•Indicates high or low values with a LED light

•Easy installation

•Easy configuration

•May be installed on a ceiling or any surface

•Battery-powered

•Long-range communication

•Configurable over NFC

•Configurable over the air

•Five years of battery life*

•Supported channel plans: US902-928, EU863-870, AS923, AU915-

928, KR920-923, RU864, IN865 & HK923

•CE Approved and RoHS compliant

*Depending on settings and environmental factors

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Installation

This device is designed to be mounted in the ceiling, directly above the presence

detection area. The field of view is 60°, the higher mounted, the smaller area for

possible detection.

1. Remove the back panel of the sensor with a small screwdriver.

2. Mount the back panel securely to the wall with at least 2 appropriate

screws, using some of the six mounting holes.

Note: ERS Eye will calculate its first background picture 15s after inserting the batteries.

It is preferable if the room is unoccupied at this time. Otherwise, it will take maximum

24h to recalibrate the background if the first background picture is inaccurate.

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

3. Install the batteries. The ERS Eye requires one or two AA batteries. The

battery type is 3.6V Lithium Battery (ER14505). You can use one battery,

but it’s recommended that you use two for best performance and battery

life. Use battery slot A if only one battery is used.

Caution: Using batteries other than the ones provided may result in loss of performance and

battery life, and also damage to the device. Dispose of properly, observing environmental

protection rules.

4. Attach the sensor part to the back panel.

Service and maintenance

No serviceable parts inside. If service is needed other than battery replacement,

please contact your distributor.

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Sensor configuration

All sensor settings can be configured via a smartphone application with NFC

(Near Field Communication) or over the air via the network server and downlink

data to the sensor. The sampling rate, spreading factor, encryption keys, port,

and modes can be changed. All sensor settings can be locked from the server or

NFC to make end-users unable to read or change settings on the sensor.

NFC Configuration

1. Download ELSYS “Sensor Settings”application from Google Play and install

it on a smartphone or tablet. The device must support NFC.

2. Enable NFC on the device and start the application.

3. Place your device on top of the NFC antenna on the sensor.

4. Remove the device. Current settings will be displayed in the application.

5. Use the application to change any settings if needed.

6. Quickly tap the device on top of the NFC antenna to give the new settings

to the sensor. Make sure that the application confirms your new settings.

7. Wait for the sensor to reboot (5 sec), indicated by the LED flashing. Sensor

settings have been updated.

See the section “Help”in the application for more information.

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Over the air configuration

All settings may be configured over the air via your LoRaWAN® infrastructure.

Please visit the support section on our webpage for more information regarding

downlink protocol.

Application parameters

All parameters for the “Sensor settings” application can be found in our settings

document. Please visit the support section on our webpage for more information.

Sensor behavior

NFC Read / Write

1. When reading or writing NFC

configuration data to the sensor, it starts

a timer and delays its action 5 seconds.

2. After the delay, the sensor determines if

the NFC data has changed or not. If it

has changed, the sensor reboots and

starts from power-up.

3. Write your settings in the application

and then locate the NFC antenna of the

phone and sensor. Keep the two

devices close and don’t move them to

get the best connectivity as possible

when writing or reading data to the

sensor. Bad connection can be caused

by long distance, wrong location, or

rapid movement.

4. When you have written data to the sensor, let the sensor reboot and restart

before trying to write again.

You should always validate your settings by reading the NFC data after the

sensor has restarted.

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden

E-mail: suppo[email protected] ǀWeb: www.elsys.se

Sensor startup

1. When the sensor starts up, it loads

configuration from the internal memory and

merges it with user configuration.

2. When the configuration is done, the sensor

writes the new settings to the NFC chip. The

sensor always writes new configurations to the

NFC chip when something changes in the

sensor or if NFC data is corrupted by an NFC

writer or phone. The sensor always writes the

new configuration to NFC chip at startup.

3. When the configuration is done, the sensor

tries to join the network if OTAA (Over the Air

Activation) is enabled.

4. The sensor LED flashes orange when it tries to

join a network. It will try to join every 10

seconds initially. This interval will increase to

save battery, at most up to one time per hour.

5. After successful connection to a network, the

sensor sends a settings packet and enters

sampling mode.

Table des matières

Autres manuels Elsys Accessoires

Elsys

Elsys ERS CO2 Manuel utilisateur

Elsys

Elsys ERS Manuel utilisateur

Elsys

Elsys ELT-2 Manuel utilisateur

Elsys

Elsys ECO Series Manuel utilisateur

Elsys

Elsys ERS Manuel utilisateur

Elsys

Elsys EMS Series Manuel utilisateur

Elsys

Elsys ERS2 Series ERS2 Lite Manuel utilisateur

Elsys

Elsys EMS Door Manuel utilisateur

Elsys

Elsys EMS Desk Manuel utilisateur

Elsys

Elsys ELT-2 HP Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur