Elsner elektronik KNX A3-B2 Mode d’emploi

Installation and Adjustment

KNX A3-B2

Door Operator Control Module

Item number 70391

1 Contents

Elsner Elektronik GmbH • Sohelngrund 167 • 75395 Ostelsheim • Germany

Door operator control module KNX A3-B2 • from software version 1.00, ETS programme version 1.0

Status: 17.12.2019 • Subject to technical changes. Errors excepted.

1. Description ........................................................................................... 3

1.0.1. Deliverables ................................................................................................... 3

1.1. Technical data ........................................................................................................... 3

2. Installation and start-up ....................................................................... 4

2.1. Installation notes ...................................................................................................... 4

2.2. Installation ................................................................................................................ 4

2.2.1. Installation location ...................................................................................... 4

2.2.2. Connection/ layout of the circuit board ....................................................... 5

2.3. Notes on mounting and commissioning ................................................................ 6

3. Addressing of the device at the bus .................................................... 6

4. Transmission protocol ......................................................................... 7

4.1. List of all communications objects ......................................................................... 7

5. Parameter setting ................................................................................ 8

5.1. General settings ....................................................................................................... 8

5.2. Door operator ........................................................................................................... 8

5.3. Input 1 / 2 ................................................................................................................ 10

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Installation, inspection, commissioning and troubleshooting of the device

must only be carried out by a competent electrician.

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

3 Description

Door operator control module KNX A3-B2 • Version: 17.12.2019 • Technical changes and errors reserved.

1. Description

The Door operator control module KNX A3-B2 has three outputs for door control

and two binary inputs.

Functions:

•3 outputs for door operation (impulse or dead-man mode)

•2 binary inputs for the bus functions switches, toggle switches, blinds,

shutters, marquees, windows, dimmers, 8 but encoders, temperature

encoders, brightness encoder, scenes

Configuration is made using the KNX software ETS. The product file can be down-

loaded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser-

vice” menu.

1.0.1. Deliverables

• Control module in the installation casing

• Connection line for outputs

• Connection line for inputs

1.1. Technical data

Housing Plastic

Colour White

Assembly Installation

Protection category IP 20

Dimensions approx. 38 x 47 x 24 (W × H × D, mm)

Weight approx. 25 g (incl. connection lines)

Ambient temperature operation -30…+50°C, storage -30…+70°C

Ambient humidity max. 95% RH, avoid condensation

Operating voltage bus voltage

Bus current max. 10 mA

Data output KNX +/- Bus connector terminal

BCU type unit's own microcontroller

PEI type 0

Group addresses max. 230

Assignments max. 230

Communication objects 20

Inputs 2 x binary inputs (for potential-free contacts),

maximum output length 5 m

Outputs 3 x semi-conductor output (open collector)

max. 60 V AC/DC, 300 mA.

For safety extra-low voltage according to the SELV

specifications only!

4 Installation and start-up

Door operator control module KNX A3-B2 • Version: 17.12.2019 • Technical changes and errors reserved.

The product conforms with the provisions of EU directives.

2. Installation and start-up

2.1. Installation notes

Installation, testing, operational start-up and troubleshooting should

only be performed by an electrician.

CAUTION!

Live voltage!

There are unprotected live components inside the device.

• National legal regulations are to be followed.

• Ensure that all lines to be assembled are free of voltage and take

precautions against accidental switching on.

• Do not use the device if it is damaged.

• Take the device or system out of service and secure it against

unintentional use, if it can be assumed, that risk-free operation is no

longer guaranteed.

The device is only to be used for its intended purpose. Any improper modification or

failure to follow the operating instructions voids any and all warranty and guarantee

claims.

After unpacking the device, check it immediately for possible mechanical damage. If it

has been damaged in transport, inform the supplier immediately.

The device may only be used as a fixed-site installation; that means only when assem-

bled and after conclusion of all installation and operational start-up tasks and only in

the surroundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

2.2. Installation

2.2.1. Installation location

Install and operate in dry interior rooms only!

Avoid condensation.

5 Installation and start-up

Door operator control module KNX A3-B2 • Version: 17.12.2019 • Technical changes and errors reserved.

2.2.2. Connection/ layout of the circuit board

CAUTION!

Unprotected live components!

The voltage connected to the switching outputs must conform with the

SELV spezifications (safety extra-low voltage)!

Connect the bus cable (red/black clamp).

Use the 8-wire connection line to connect the outputs and the 4-wire line to connect the

binary inputs. The lines may be extended to up to 5 m.

Outputs

Binary inputs

Programming button

Programming LED

KNX bus clamp

Fig. 1

(connector for

4-wire line)

(connector for 8-wire line)

Fig. 2

8-wire connection line for outputs:

Connection of the outputs independent from polarity.

blue output 3

black output 3

violet (not connected)

black output 2

yellow output 2

black (not connected)

white output 1

black output 1

6 Addressing of the device at the bus

Door operator control module KNX A3-B2 • Version: 17.12.2019 • Technical changes and errors reserved.

2.3. Notes on mounting and commissioning

Device must not be exposed to water (rain). This could result in the electronics being

damaged. A relative air humidity of 95% must not be exceeded. Avoid condensation.

After the bus voltage has been applied, the device will enter an initialisation phase last-

ing a few seconds. During this phase no information can be received or sent via the

bus.

3. Addressing of the device at the bus

The device is supplied with the bus address 15.15.250. You can program another ad-

dress into the ETS by overwriting the 15.15.250 address or by teaching via the pro-

gramming button.

Fig. 3

4-wire connection line for binary inputs:

Connection of the outputs independent from polarity.

violet input 1

yellow input 1

white input 2

black input 2

7 Transmission protocol

Door operator control module KNX A3-B2 • Status: 17.12.2019 • Technical changes and errors reserved.

4. Transmission protocol

Units:

Time in seconds

Dimming in percent

Temperature in 0.1°C

Brightness in kLux

4.1. List of all communications objects

EIS types:

1 1 / 0 switch

5 Floating decimal value

6 8-bit value

Abbreviation flags:

R Reading

WWriting

C Communication

T Transmission

No.

Text Function DPT Length

(byte)

Flags

0 Output 1 - Impulse

[In Defined Open/Close/Stop

mode:

Output 1+2 - Impulse

(1=open | 0=close)]

Input 1.001 1 RC

1 Output 2 - Impulse Input 1.001 1 RC

2 Output 3 - Impulse

[In Defined Open/Close/Stop

mode:

Output 3 - Impulse (1 or 0)]

Input 1.001 1 RC

11 Input 1 Extended Input/Output 1.008 1 RWCT

12 Input 1 Short Output 1.010 1 R CT

13 Input 1 Switching Input/Output 1.001 1 RWCT

14 Input 1 Relative dimming Input/Output 3.007 1 RWCT

15 Input 1 Encoder 8 bit Output 5.* 1 R CT

16 Input 1 Encoder Temperature Output 9.001 2 R CT

17 Input 1 Encoder Brightness Output 9.004 2 R CT

18 Input 1 Scene Output 18.001 1 R CT

19 Input 2 Extended Input/Output 1.008 1 RWCT

20 Input 2 Short Output 1.010 1 R CT

21 Input 2 Switching Input/Output 1.001 1 RWCT

8 Parameter setting

Door operator control module KNX A3-B2 • Status: 17.12.2019 • Technical changes and errors reserved.

5. Parameter setting

The parameter defaults are underlined.

5.1. General settings

Set themaximum telegram rate:

5.2. Door operator

You define the operating mode for the outputs in the Door operation menu.

If only one door is connected to the three outputs (two- or three-button operation,

output 1 = open, output 2 = close, if needed output 3 = stop), select Defined Open/

Close/Stop mode or Impulse mode.

If a door is connected to each output (single-button operation), select Impulse mode or

dead-man mode.

Defined Open/Closed: (1 door)

The outputs 1 and 2 react to the object (are assigned to the object) Output 1+2 -

Impulse. If the object value is 1, then output 1 receives an impulse (closes for 1s). If the

object value is 0, then output 2 receives an impulse (closes for 1 s).

Output 3 is asigned to the object Output 3 - Impulse. The output reacts as soon as an

object has been received (no matter which value).

Select whether output 3 is a normally closed or normally open contact (duration of

opening/closing 1 second).

22 Input 2 Relative Dimming Input/Output 3.007 1 RWCT

23 Input 2 Encoder 8 bit Output 5.* 1 R CT

24 Input 2 Encoder Temperature Output 9.001 2 R CT

25 Input 2 Encoder Brightness Output 9.004 2 R CT

26 Input 2 Scene Output 18.001 1 R CT

27 Software version Readable 217.001 2 R C

Maximum message rate 1 • 2 • 5 • 10 • 20 messages per second

Operating mode • Defined Open/Close/Stop

• Impulse mode

• Dead-man mode

Operating mode Defined Open/Closed/Stop

Allows control of one door

No.

Text Function DPT Length

(byte)

Flags

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels elsner elektronik Unité de contrôle

elsner elektronik

elsner elektronik WS1000 Style Manuel utilisateur

elsner elektronik

elsner elektronik IMSG-UC-4H Manuel utilisateur

elsner elektronik

elsner elektronik IMSG 230 compact Manuel utilisateur

elsner elektronik

elsner elektronik MSG1 compact Manuel utilisateur

elsner elektronik

elsner elektronik RF-MSG-DST Manuel utilisateur

elsner elektronik

elsner elektronik IMSG-UC-2H Manuel d'instructions

elsner elektronik

elsner elektronik RF-MSG-ST IP53 Manuel utilisateur

elsner elektronik

elsner elektronik WS1000 Style Guide de référence

elsner elektronik

elsner elektronik IMSG-UC-2H Manuel utilisateur

elsner elektronik

elsner elektronik RF-MSG-ST IP54 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

elsner elektronik KNX A3-B2 Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques