ELECTROCOMPANIET PI 2D Manuel utilisateur

PI 2D

Balanced Integrated Ampliﬁer

(with built-in DAC)

Owner's Manual

ENG

Unpacking the PI 2D

Immediately upon receipt of the amplifier, inspect the carton for possible dam-

age during shipment. If the carton is visibly damaged, a claim must be filed

with the carrier as soon as possible.

Unpack the unit carefully, and please do remember to save all packaging

materials for future shipment. The carton and packaging have been designed to

offer the safest possible protection when transporting your amplifier.

The contents of the carton

•1 pc. Electrocompaniet PI 2D Integrated Amplifier

• 1 pc. AC power cord

• 1 pc. Owner's Manual

• 1 pc. Inspection Card

• 1 pc. Remote control

• 2 pcs. batteries.

Set up procedure

Before connecting the PI 2D to the mains, check that the main voltage

indicated on the rear panel corresponds to the line voltage in the terri-

tory where you intend to use the unit.

How to avoid damages

A good operating practice is to turn off all equipment before any con-

nections or disconnection’s are made. Do not under any circumstances

connect or disconnect equipment when power is turned on. The design

of the RCA plug generates a huge transient when inserted. Connecting

or disconnecting equipment with the power on can result in severe

damage to both speakers and amplifier.

How to avoid noise problems

The PI 2D contains delicate circuits that are sensitive to magnetic stray

fields. The unit should not be placed near main transformers, TV sets,

etc. Care should also be taken regarding placement of the interconnect

cables. Do not run interconnect cables in parallel with main cords or

speaker cables. Keep interconnect cables as short as possible.

How to avoid possible antenna problems

In some setups hum may occur when you connect the radio, VCR or TV

to your system. The problem is caused by DC voltage coming from your

antenna. Please contact your cable network operator.

ENG

How to connect your system

( See illustration, page 10.)

Single - ended operation: (

See illustration "back panel", page 9.)

There are 4 sets of single ended inputs labelled: DVD, Tuner, AUX, HT.

All inputs are similar regarding sonic performance.

Balanced operation: (

See illustration "back panel", page 9.)

There are one set of balanced inputs labeled CD. The balanced mode can

only be used if the signal source has a balanced output. Use an XLR inter-

connect with GND on pin 1, + on pin 2 and – on pin 3.

Speaker outputs (

See illustration "back panel", page 9.)

Connect the red connector to the plus side on the speakers and the white

connector to the minus side on the speakers. Never short the positive output to

ground or chassis. Always switch the PI 2D off when you connect the speakers.

Front panel (

See illustration "front panel", page 8.)

The standby button is located on the left side of the front panel.

The four buttons on the right-hand side of the front panel is used to adjust

the volume and select the input source. Use the up and down buttons to

adjust the volume, and the left and right buttons to select input source. The

volume range is 0 to 100.

HT (Home Theatre)

HT is a direct input where the volume control is bypassed. PI 2D will

work like a power amplifier with fixed gain. When selected the output

will be muted for a few seconds as a safety against accidental overload.

SPDIF inputs

PI 2D will accept optical SPDIF sources up to 96 kHz/24bit on inputs

TOSLink1 and TOSLink2. Please use a optical TOSLink cable for this con-

nection. Connect coaxial sources up to 192kHz/24bit to inputs COAX1

and COAX2. Please use a coaxial SPDIF cable for this connection.

USB input

( See illustration "back panel", page 9.)

The USB input accept sources up to 24bit/192kHz. Connect a PC/Mac/

Linux computer using a standard type A-B USB cable. PI 2D will show up

as a sound device on your computer. Please select PI 2D as the active

device to enable playback through PI 2D. On Windows drivers are

needed. Please install the drivers before connecting the USB cable and

follow the instructions. During installation you will be asked to connect

the USB cable. The latest drivers can be downloaded from: www.electro-

companiet.no/downloads.

How to power up your system

You should always power up your system the following way:

Signal sources (CD player, tuner etc.) first. Allow a 30 seconds warm-up

before you turn on the PI 2D.

ENG

This window in the middle of the front panel shows which source is currently

active. The listening volume will be displayed when the volume is adjusted

using the remote control or the navigator up/down buttons. The display may

be turned off using the DIM AMP button on the remote. If turned off, the dis-

play will come back on for 5 seconds if any button is pressed on the remote

or the navigator.

Audio

Source

Display

Text

Description

CD CD Analog balanced XLR input

AUX AUX Analog single-ended RCA input

DVD DVD Analog single-ended RCA input

HT HT Analog single-ended home theater RCA input

COAX 1 COAX1 Coaxial S/PDIF input up to 192 kHz/24 bit

COAX 2 COAX2 Coaxial S/PDIF input up to 192 kHz/24 bit

TosLink 1 TOSLNK1 Optical S/PDIF input up to 96 kHz/24 bit

TosLink 2 TOSLNK2 Optical S/PDIF input up to 96 kHz/24 bit

Tuner TUNER Analog single-ended RCA input

USB USB Asynchronous High Speed USB 2.0 input up to

192kHz/24bit

Navigator buttons (

See illustration "front panel", page 8.)

Button Function Description

UP Volume Up Increases the volume level.

DOWN Volume Down Decreases the volume level.

LEFT Select source left Selects previous source

RIGHT Select source right Selects next source

Navigator window

(

See illustration "front panel", page 8.)

ENG

Error codes

If the PI 2D is not working properly, the display will show an error code.

For other troubleshooting please contact your local dealer or our support

department. All contact information you will find at www.electrocompaniet.no

Error text Description What to do

DC L DC voltage left channel Please contact service center.

DC R DC voltage right

channel

DC DC left + right channels

OVRLD L Overload left channel

Make sure that the + and – leads

of the loudspeaker cables are

not shorted, and that the speaker

cables are not in contact with the

chassis of PI 2D.

OVRLD R Overload right channel

OVRLOAD Overload left+right chan-

nels

TEMP L Left channel overheated The ampliﬁer is overheated. This

is caused by either playing to

loud for a long period of time,

or not enough free space on the

sides or above the PI 2D.

Turn down the volume and make

sure there is enough free space

around the ampliﬁer.

TEMP R Right channel overheated

TEMP Left+Right channels

overheated

ENG

1. Mute on/off.

(Hold 1-2 sec to set into standby mode.)

2. CD - switch to CD input.

3. TUN - switch to Tuner input.

4. COAX1 - switch to COAX1 input.

5. TOSLink 1 - switch to TOSLink 1 input.

6. COAX2 - switch to COAX2 input.

7. TOSLink 2 - switch to TOSLink 2 input.

8. USB - switch to USB input.

9. AUX - switch to AUX input.

10. No function on PI 2D.

11. AMP DIM - turn display on/off.

12. DVD - switch to DVD/Blu-ray input.

13. Vol Up - increases the volume level.

14. Vol Down - decreases the volume level.

15. HT - switch to Home theater input.

Remote control operating guide

ENG

1. Mute on/off.

(Hold 1-2 sec to set into standby mode.)

2. CD - switch to CD input.

3. TUN - switch to Tuner input.

4. COAX1 - switch to COAX1 input.

5. TOSLink 1 - switch to TOSLink 1 input.

6. COAX2 - switch to COAX2 input.

7. TOSLink 2 - switch to TOSLink 2 input.

8. USB - switch to USB input.

9. AUX - switch to AUX input.

10. No function on PI 2D.

11. AMP DIM - turn display on/off.

12. DVD - switch to DVD/Blu-ray input.

13. Vol Up - increases the volume level.

14. Vol Down - decreases the volume level.

15. HT - switch to Home theater input.

Important Notice

For optimal sonic performance, the PI 2D should be burned in for a

minimum time of 72 hours. If the PI 2D has been switched off, allow two

hours of warm-up for optimal sonic performance. It is normal for the

PI 2D to feel warm. A good rule of thumb is to allow at least 3 - 5 cm

(1 - 2 inches) of air sidewise, and 5 - 8 cm(2 - 3 inches) above the PI 2D

If service is needed

Your dealer will have all relevant information regarding the service

centre in your area and will ensure that your unit is serviced with mini-

mum delay. If, for some reason, there are no service facilities available

in your country, please contact Electrocompaniet for assistance:

ELECTROCOMPANIET AS

BREIVIKVEIEN 7

4120 TAU

NORWAY

Web: www.electrocompaniet.no

The end-user is responsible for all shipping charges, insurance and all

re-importation and duty charges. When shipping a product to the fac-

tory for service, always include the following:

1. A sales slip or other proof of purchase if repair is claimed under warranty.

2. A proforma invoice with value of goods, stating that the amplifier is

being returned to Norway for repair.

3. An accompanying letter describing faults, symptoms, or problems with

the unit.

4. Always ship the unit in its original carton and packaging material

to prevent damage in transit. Electrocompaniet will not cover damages

incurred in transit.

If you require further information concerning the operation of the unit or

if you have any questions related to service, please do not hesitate to

contact your dealer or national distributor.

ENG

PI 2D High Performance Balanced Integrated Amplif

ier - DAC

MODEL:PI 2D

ELECTROCOMPANIET

MADE IN NORWAY

DIGITAL INPUT ANALOG INPUT

RIGHT OUTPUT LEFT OUTPUT

USB TOSLINK1 TOSLINK2 COAX1 COAX2

CAUTION

RISK OF ELECTRICAL SHOCK

The removal of the top cover may cause

electric shock. No user servicebale parts inside.

Refer to authorized service personnel.

Do not exprose to moisture or rain.

8910 11 12 13 14

6 7

4 5

321

1. Standby button

2. Display

3. Previous input

4. Volume down

5. Next input

6. Volume up

PI 2D front panel illustration

ENG

PI 2D High Performance Balanced Integrated Amplif

ier - DAC

MODEL:PI 2D

ELECTROCOMPANIET

MADE IN NORWAY

DIGITAL INPUT ANALOG INPUT

RIGHT OUTPUT LEFT OUTPUT

USB TOSLINK1 TOSLINK2 COAX1 COAX2

CAUTION

RISK OF ELECTRICAL SHOCK

The removal of the top cover may cause

electric shock. No user servicebale parts inside.

Refer to authorized service personnel.

Do not exprose to moisture or rain.

8910 11 12 13 14

6 7

4 5

321

1. USB audio input

2. Optical digital input 1, TOSLink1

3. Optical digital input 2, TOSLink2

4. Coaxial digital input 1

5. Coaxial digital input 2

6. Power inlet

7. Serial number and voltage.

8. Right speaker output

9. Balanced analog right CD input

10. Balanced analog left CD input

11. DVD/Blu-ray analog input

12. Tuner analog input

13. AUX analog input

14. Home theater analog input (HT)

15. Left speaker output

PI 2D back panel illustration

ENG

PC / MAC

DVD / Blu-ray player

CD player

Media Player

MODEL : PI 2D

ELECTROCOMPANIET

MADE IN NORWAY

DIGITAL INPUT ANALOG INPUT

RIGHT OUTPUT LEFT OUTPUT

USB TOSLINK1 TOSLINK2 COAX1 COAX2

CAU T I O N

RISK OF ELECTRICAL SHOCK

The removal of the top cover may cause

electric shock. No user servicebale parts inside.

Refer to authorized service personnel.

Do not exprose to moisture or rain.

How to connect the system

Table des matières

Autres manuels ELECTROCOMPANIET Amplificateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW-250 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6DS Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI4 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW220 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6D Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW 250R Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 80D Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECP1 MC Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.8 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW 180 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW600 NEMO Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI2 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW400 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI3 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW 180 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.9 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET EC4R Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.7 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECC-1 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW 800 M Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET PI-1 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET AW 120 Manuel utilisateur

ELECTROCOMPANIET

ELECTROCOMPANIET PI-2 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur