Elation EVLED256 Video Wall Manuel utilisateur

EVLED256 Video Wall

Quick Start Guide

I. PC and Controller connections

1. Connect EVLED VSC controller to the graphics card on the PC with the included DVI cable. Connect EVLED VSC RJ11 port to the RS232

port on the PC with the included RS232 signal cable as pictured below. If your PC does not include RS232, use the included RS232 to

USB convertor.

2. On your PC, set up a secondary or clone display. A flashing green LED on the rear of the EVLED VSC indicates successful

communication.

One end of DVI cable connects with sending card in EVLED VSC controller

Connect theRS232 data cable into your PC (Use the RS232 to USB convertor if you

don’t have RS232 on your PC). Connect RJ11 end into the EVLED-VSC. The other end of DVI cable connects with PC graphic card

EVLED VSC Controller

ELATION

II. Power and data cable connection map. (Example map: 3 rows by 3 columns). This connection type is only recommended for up to 20

panels. When using more than 20 panels, an EVLED VDS data splitter should be used. Contact your Elation representative for a

custom connection map.

III. Application of Software

1. Launch LED Set software; click “Parameter” as pictured below.

Parameter

2. A password window will pop up as pictured below. Input password “168” and click “Ok”.

3. Sending card resolution set up: If your screen works in 1024×768 resolution mode, there is no need to select another display mode. If it does not,

click the “Display mode” drop down tab and select the correct displayresolution for your screen. Click “Save on sender” to confirm.

4. Installation of receiving card: Click “Receiver” tab. Window should display as pictured below.①Click “Load from files”→select

“EVLED256.RCG” ②Click “Send to receiver”→③Click “Save on receiver”.

Switch to “Receiver” setup screen

1. Load EVLED256.RCG panel profile 2. Send profile to receiver 3. Saving profile to sending card

(See next page for more info)

Select Profile (EVLED256.RCG)

5. Mapping and setup: (For example: to map 3 rows and 3 columns, setup should be as pictured below)

Update the quantity of screens if using more than one main screen→In “Type”, select “virtual pixel display”→set rows and columns for your

screen→select pixel points of each panel (The pixel points for each EVLED256 is 16x16)→set the map based on the signal connection (Ztype

connection as pictured below). Follow steps 1 – 9 in order. (1). Input number of screens

(2). Click “Update display QTY”

(3). Type: select “virtualpixel display” (4). Number of panels wide

(5). Number of panels high

(7). Signal connection:

(Front view data connection) (9). Save parameter to sending card.

(6). Input the number of pixel points for each panel. The EVLED256

Panel should be set as16 Width by 16 Height. (8). Send settings to sending card.

*NOTE: The EVELED VSC can control/drive up to 1280x1024 resolution. So if using EVLED256 panels, one (1) EVLED VSC controller

can drive a wall size of up to 80 panels wide by 64 panels high. Up to ten (10), EVLED256, panels can be connected into a single 20A

circuit.

6. Adjust play area start position: By default, the X/Y start position coordinates are 0 for X and 0 for Y. These coordinates place the play area in

the upper left corner of your PC monitor.

The X start point refers to the width of your monitor. The Y start point refers to the height of your monitor. Simply input the number of pixels that

you want the play area of your screen moved to then click “Set New”. For example, if I wanted to move my play area down 50 pixels, I’d input a

value of 50 into the “Start Y” box and click “Set New”. The play area will immediately move down and display whatever is currently in that area onto

your video wall.

Autres manuels pour EVLED256 Video Wall

Autres manuels Elation Équipement d'éclairage

Elation

Elation Elar Quad Par Manuel utilisateur

Elation

Elation ELAR ELAR IPX Manuel utilisateur

Elation

Elation Design Spot 300E Manuel utilisateur

Elation

Elation Color Spot 575 Manuel utilisateur

Elation

Elation CHORUS LINE 8 Manuel utilisateur

Elation

Elation SIXBAR 500 Manuel utilisateur

Elation

Elation Waterfall 250 Pro Manuel utilisateur

Elation

Elation KL FRESNEL 8 FC Manuel utilisateur

Elation

Elation SIXPAR 100WMG Manuel utilisateur

Elation

Elation CUEPIX BATTEN Manuel utilisateur

Elation

Elation PowerWash 250 Manuel utilisateur

Elation

Elation ELAR Tri Brick Manuel utilisateur

Elation

Elation KL FRESNEL 8 PO Manuel utilisateur

Elation

Elation SIXPAR 200WMG Manuel utilisateur

Elation

Elation Level Q7 IP Manuel utilisateur

Elation

Elation Pro FS 1000 Manuel utilisateur

Elation

Elation VISION 575 Manuel utilisateur

Elation

Elation FUZE PAR Z175 Manuel utilisateur

Elation

Elation Power Spot 700 CMY II Manuel utilisateur

Elation

Elation Opti Tri 30 Manuel utilisateur

Elation

Elation UNI BAR Manuel utilisateur

Elation

Elation PROTEUS HYBRID Manuel utilisateur

Elation

Elation Event Cylinder RF Manuel utilisateur

Elation

Elation ELED TW Strip Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur