Elation FUZE PENDANT Manuel utilisateur

FUZE PENDANT™

user manual

and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and

identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL.

information now allowed by statutory or judicial law or hereinafter granted. Product names used in

this document may be trademarks or registered trademarks of their respective companies and are

hereby acknowledged. All non-ELATION brands and product names are trademarks or registered

trademarks of their respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for

property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect

economic loss associated with the use or reliance of any information contained within this document,

and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and

operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 |323-832-9142 fax | www.elationlighting.com |[email protected]

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

+31 45 546 85 66 |+31 45 546 85 96 fax |www.elationlighting.eu |[email protected]

Elation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

DOCUMENT VERSION

Due to additional product enhancements, an updated version of this

document may be available online. Please scan the QR Code with

your mobile device or visit www.elationlighting.com for the latest

revision/update of this manual before installation and/or

programming.

Date

Document

Version

Software

Version ≥

DMX

Channel Modes

Notes

01/16/20

1.0

1.01H

Dimmer1CH, Dimmer Color 4CH, RGBWL

5CH, RGBWL 16bit 10CH, Standard 10CH,

Extended 17CH, HSI 4CH, HSI Extended 9CH

Preliminary release.

02/25/20

1.1

1.2

NO CHANGE

Updated overview and system

menu.

04/06/20

1.2

NO CHANGE

Updated Optional Accessories.

CONTENTS

General Information

Warranty Returns (USA Only)

Safety Guidelines

Maintenance Guidelines

Overview

Optional Accessory Installation Guidelines

Fixture Installation Guidelines

E-FLY Wireless Set Up Guidelines

System Menu

Dimmer Modes

DMX Channel Functions

Color Temperature Table

Virtual Gel Swatch Book Table

Error Codes

Specifications

Dimensional Drawings

Optional Accessories | FCC Statement

GENERAL INFORMATION

INTRODUCTION

Please read and understand the instructions in this manual carefully and thoroughly before attempting

to operate this fixture. These instructions contain important safety and use information.

UNPACKING

Every fixture has been thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If the carton

is damaged, carefully inspect the fixture for damage, and be sure all accessories necessary to install

and operate the fixture have arrived intact. In the event damage has been found or parts are missing,

please contact our customer support team for further instructions. Please do not return this fixture to

your dealer without first contacting customer support. Please do not discard the shipping carton in

the trash. Please recycle whenever possible.

BOX CONTENTS

45°Lens

Pendant Bracket Kit

Locking IP65 Power Cable

CUSTOMER SUPPORT

Contact ELATION Service for any product related service and support needs.

Also visit forums.elationlighting.com with questions, comments or suggestions.

ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

323-582-3322 | Fax 323-832-9142 | [email protected]

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

+31 45 546 85 63 | Fax +31 45 546 85 96 | [email protected]

REPLACEMENT PARTS please visit parts.elationlighting.com

IMPORTANT NOTICE!

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR

MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS

TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND

GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND

ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.

WARRANTY RETURNS (USA ONLY)

To obtain warranty service, a Retur n M a t e r i a l s A u t h o r i z a t i o n ( R M A ) n u m b e r m u s t f i r s t b e o b t a i n e d f rom

ELATION. It is the Customer’s responsibility to provide product proof of purchase and serial number by

acceptable evidence such as an invoice copy or an approved ELATION Extended Warranty Certificate

(“EWC”) and any relevant maintenance records at the time warranty service is sought. Failure to provide

acceptable evidence of product proof of purchase or EWC and any relevant maintenance records may be

cause for denial of warranty service.

Products returned for warranty service must be sent without any accessories (i.e., power, data, and safety

cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn doors, lens, hoses, nozzles, rack

mounting hardware, etc.), must be boxed using the original and/or suitable packaging materials (double-

box and foam) that provides ample product protection for ground and/or air freight transit, and must be

shipped freight pre-paid and insured to ELATION in Los Angeles, CA or an ELATION Authorized Service

Center. The RMA number must be clearly written on the outside of the return box, and a brief description

of the problem and the RMA number must be documented and included in the box.

Products returned for warranty service without an RMA number clearly marked on the outside of the

package will be refused and returned to the shipper at the Customer’s expense. Products returned for

warranty service, which are received damaged due to inadequate and/or improper packaging and/or due

to damage caused by shipping carrier, may incur additional repair charges before warranty service begins

and/or may void this warranty. If any product accessories (included and/or optional) are shipped with the

product, ELATION and/or the ELATION Authorized Service Center shall have no liability what so ever for

the loss and/or damage to any such accessories, nor the safe return thereof. If the requested warranty

repairs or service (including parts replacement) are within the terms of this warranty, ELATION will pay

return ground transportation shipping charges to a single designated point within the United States.

SAFETY GUIDELINES

This fixture is a sophisticated piece of electronic equipment. To guarantee a smooth operation, it is

important to follow all instructions and guidelines in this manual. Elation Professional is not

responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard

of the information printed in this manual. Only qualified and/or certified personnel should perform

installation of this fixture and only the original rigging and mounting hardware included with this

fixture or available optional accessories should be used for installation. Any modifications to the

fixture and/or the included and optional rigging and mounting hardware will void the original

manufacturer’s warranty and increase the risk of damage and/or personal injury.

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID

YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM

MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF

SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE

MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY

WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

INDOOR / DRY LOCATIONS USE ONLY!

DO NOT EXPOSE FIXTURE TO RAIN AND/OR MOISTURE!

MINIMUM DISTANCE TO OBJECTS/SURFACES

IS 1.0 FOOT (0.3 METER)

MINIMUM DISTANCE OF FLAMMABLE MATERIALS

FROM THE SURFACE IS 1.6 FEET (0.5 METER)

MAXIMUM AMBIENT OPERATING TEMPERATURE IS 113°F (45°C)

SAFETY GUIDELINES

DO NOT TOUCH the fixture housing during operation.

DO NOT shake fixture, and avoid brute force when installing and/or operating fixture.

DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if any of the power cord

connectors are damaged or do not fit into the fixture securely with ease.

NEVER force a power cord connector into the fixture. If the power cord or any of its connectors are

damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

TURN OFF the power and allow approximately 15 minutes for the fixture to cool down before serving.

ALWAYS disconnect fixture from power before performing any service and/or cleaning procedure.

ONLY handle power cord by the plug end, never pull plug out by tugging the wire portion of the cord.

During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture.

This is a normal process and is caused by excess paint in the interior of the casing burning off from the

heat associated with the LED and will decrease gradually over time.

Consistent operational breaks will ensure fixture will function properly for many years.

ONLY use the original packaging and materials to transport the fixture for service.

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an

extended life. The frequency of cleaning depends on the environment in which the fixture operates:

damp, smoky or particularly dirty environments can cause greater accumulation of dirt on the

fixture’s optics. Clean periodically with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life.

There are no user serviceable parts inside this fixture, please refer all other service issues to an

authorized Elation service technician. Should you need any spare parts, please order genuine parts

from an authorized Elation dealer.

Please refer to the following points during routine inspections:

• A detailed electric check by an approved electrical engineer every three months, to make sure the

circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during

normal operation resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware and rigging points

(ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the

fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously

injure a person(s).

• Electric power supply cables must not show any damage, material fatigue or sediments.

• NEVER remove the ground prong from the power cable.

OVERVIEW

1. Locking Power Connector

2. DMX Input – 5-pin XLR Male

3. DMX Output – 5-pin XLR Female

4. Wired Power Input Cable Gland

5. Wired DMX Cable Gland

6. Power Input Switch

7. Emergency Power Input Terminal

OVERVIEW

POWER CONNECTIONS

Power may be provided to the fixture by means of an industry standard locking power connector (1).

Alternately, for more permanent installations, a power line may be wired to the fixture by connecting a

line to the wired power input cable gland (4). A wiring block is located directly behind this gland,

with wire terminals for Live (L), Neutral (N), and Floating Ground (FG). This terminal block is accessed

by removing the center plate in the connection panel.

Additionally, the fixture may be configured to draw power from either input by means of the power

input switch (6). The fixture will draw power from the locking power connector (1) when the switch

is set to the “EXT” position, or the wired power input cable gland (4) when the switch is set to the

“INT” position.

DMX CONNECTIONS

DMX communication to and from the fixture may be provided by the DMX 5-pin male XLR input (2)

and the DMX 5-pin female XLR output (3). Alternately, for more permanent installation, a DMX line

may be wired to the fixture by connecting the line to the wire DMX cable gland (5). A wiring block is

located directly behind this gland, with wire terminal for DMX +, DMX -, and DMX GND. This terminal

block is accessed by removing the center plate in the connection panel. The terminal block also

contains two additional terminals for 10V+ and 10V-, but these terminals are discussed in the following

section.

0-10V / CONTACT CLOSURE CONNECTION

The terminal block that is used for the hard-wired DMX connections also includes terminals for 10V+

and 10V-. These two terminals may be used to connect the fixture to a current sink 0-10V dimmer to

enable adjustment of lighting intensity, or they may be used to connect the fixture to a contact closure

such as a wall switch or an emergency alarm panel.

EMERGENCY POWER

The emergency power input terminal (7) can be connected to a 25-48V DC power source in order

to provide emergency lighting in the event of loss of AC power. The DC power source should be rated

for 15W or 20W in order to provide sufficient power for the fixture to operate for a minimum of 90

minutes. Please note that neither color nor light output will be adjustable when the fixture is operating

in this mode, as the fixture has been optimized for maximum runtime at the required light levels.

Please note that it is the responsibility of the user to determine the system design, wiring, and

illumination levels required by law for emergency lighting systems in the locality in which the

system will be operating. Emergency lighting must comply with all applicable national, state,

and local standards.

Table des matières

Autres manuels Elation Luminaire

Elation

Elation ELED QA Strip Manuel utilisateur

Elation

Elation Design Spot 575B Manuel utilisateur

Elation

Elation DESIGN WASH 250 Manuel utilisateur

Elation

Elation E SPOT III Manuel utilisateur

Elation

Elation TVL1000-II Manuel utilisateur

Elation

Elation PRS022 Manuel utilisateur

Elation

Elation ZW19 Manuel utilisateur

Elation

Elation ACL BAR Manuel utilisateur

Elation

Elation PROTEUS HYBRID Manuel utilisateur

Elation

Elation COLOUR CHORUS 48 Manuel utilisateur

Elation

Elation PLATINUM FLX Manuel utilisateur

Elation

Elation Vision Scan 250 Manuel utilisateur

Elation

Elation TVL F1WW Manuel utilisateur

Elation

Elation ProTron LED Manuel utilisateur

Elation

Elation ELAR TRI PAR IP Manuel utilisateur

Elation

Elation Power Spot 575IE II Manuel utilisateur

Elation

Elation Platinum Beam 5R Extreme Manuel utilisateur

Elation

Elation ACL 360i Manuel utilisateur

Elation

Elation FUZ418 Manuel utilisateur

Elation

Elation PIXEL BAR 40 Manuel utilisateur

Elation

Elation ELAR EX TRIBAR Manuel utilisateur

Elation

Elation TVL2000 II Manuel utilisateur

Elation

Elation 60TM Manuel utilisateur

Elation

Elation FUZE SFX WH Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur