Elatec TWN4 MultiTech 2 HF Manuel utilisateur

TWN4

MultiTech Mini

DocRev5, February 5, 2019

Elatec GmbH

Contents

1Introduction............................................... 3

2Dimensions............................................... 4

3Connectors............................................... 5

4UsingPIOption ............................................ 6

4.1 SIO Chip soldered on PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.2 SAM Card Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5Disclaimer ............................................... 7

Page 2of 7

1 Introduction

TWN4 MultiTech Mini is a module to be integrated on custom PCB. It has a built-in HF antenna and subset

of IOs compared to TWN4 Core Module. TWN4 Mini Reader is currently available as version TWN4 Mini

Reader MIFARE NFC.

Page 3of 7

2 Dimensions

Below are the dimensions of the TWN4 MultiTech Mini. All dimensions in mm unless otherwise stated.

Page 4of 7

3 Connectors

The TWN4 Mini Reader has two on-board single row headers with 8 positions each. The pins of these two

connectors are together enumerated from 1 to 16.

• Single row header

• Pitch 2.54mm

• Pin shape square 0.635mm

Pin Pin Name Function

1 RESET- Low active TTL input with internal pull-up resistor for hard re-

set.

2 PWRDWN- Low active TTL input with internal pull-up resistor for turning

off the voltage regulator.

3 GND Ground

4 VIN Unregulated input to on-board voltage regulator

5 RXD- Low active TTL input with internal pull-up resistor of asyn-

chronous RXD to COM1.

6 TXD- Low active TTL output (push/pull) of asynchronous TXD from

COM1.

7 Res. Reserved for future use (intended for SCK from SPI host in-

terface).

8 Res. Reserved for future use (intended for SS- from SPI host inter-

face).

9 VCC Internaly regulated 3.0V power supply. To be used for SAM1.

10 SAM_IO I/O line for SAM1.

11 GPIO3 GPIO3, I/O pin for general purposes.

12 GPIO2 GPIO2, I/O pin for general purposes.

13 GPIO1 GPIO1, I/O pin for general purposes.

14 GPIO0 GPIO0, I/O pin for general purposes.

15 SAM_CLK Clock output for SAM1

16 SAM_RST Reset output for SAM1

Page 5of 7

4 Using PI Option

To use the PI Option, e.g. to read the PAC bits from an iCLASS transponder, a SIO processor is needed.

This can be either a SIO chip which is soldered directly on a PCB or a SAM card incorporating the SIO

processor.

4.1 SIO Chip soldered on PCB

The SIO processor has to be added to the design of the mainboard. The chip shall be connected to the

SAM-pins of the TWN4 Mini Reader.

Recommended schematic:

4.2 SAM Card Connection

A SAM socket has to be added to the design of the mainboard. The SAM socket shall be connected to the

SAM-pins of the TWN4 Mini Reader.

Following SAM sockets are recommended:

• Molex 47388-2001

• Molex 47308-0001

Recommended schematic:

Page 6of 7

5 Disclaimer

Elatec reserves the right to change any information or data in this document without prior notice. The

distribution and the update of this document is not controlled. Elatec declines all responsibility for the use

of product with any other speciﬁcations but the ones mentioned above. Any additional requirement for a

speciﬁc custom application has to be validated by the customer himself at his own responsibility. Where

application information is given, it is only advisory and does not form part of the speciﬁcation.

All referenced brands, product names, service names and trademarks mentioned in this document are the

property of their respective owners.

Page 7of 7

Autres manuels pour TWN4 MultiTech 2 HF

Table des matières

Autres manuels Elatec Unité de contrôle

Elatec

Elatec TWN3 LEGIC NFC M Manuel utilisateur

Elatec

Elatec TWN4 PALON SQUARE M LF HF Manuel d'utilisation et d'entretien

Elatec

Elatec TWN4 MultiTech 2 HF Manuel utilisateur

Elatec

Elatec TWN4 MULTITECH LEGIC M Manuel d'utilisation et d'entretien

Elatec

Elatec TWN4 Slim LEGIC Manuel utilisateur

Elatec

Elatec TWN4 MultiTech 2 HF Manuel utilisateur

Elatec

Elatec TWN3 MIFARE Manuel utilisateur

Elatec

Elatec TWN3 LEGIC NFC Manuel utilisateur

Elatec

Elatec TCP3 3.0.3.1 Manuel utilisateur

Elatec

Elatec TWN3 MINI Manuel utilisateur

Elatec

Elatec TWN4 MULTITECH LEGIC M Manuel utilisateur

Elatec

Elatec TWN4 PALON SQUARE M LF HF Manuel utilisateur

Elatec

Elatec TWN4 MultiTech 2 HF Manuel d'utilisation et d'entretien

Elatec

Elatec TWN4 MultiTech 2 HF Manuel utilisateur

Elatec

Elatec TWN4 MultiTech 2 HF Note de version

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur