Ei Electronics MCP401RC Manuel utilisateur

MCP401RC Manual Call Point

Disconnect the AC mains power supply from the circuit that is to

be used to power the smoke/heat alarms and the MCP401RC.

Install the Smoke/Heat/CO Alarms as per the Installer

Instructions supplied with the alarms.

Select a suitable location where the MCP401RC can be easily

accessed. The unit should not be exposed to dripping or splashing.

Route the wiring (Live, Neutral, Interconnect/Control and Earth)

to the MCP401RC siting location. A minimum 0.75mm2cable

should be used.

With the 25mm screws provided, fix the mounting box to the wall.

SURFACE MOUNTING BOX

FRONT COVER

OPERATING ELEMENT

SCREW (2)

3.5 x 25mm

Figure 1

Installation & Wiring

Figure 2

To additional Ei Alarms

if required

(compatible alarms

listed above)

Figure 3

When the black spot on the front face of the MCP401RC is pressed, an alarm signal will be sent along the

interconnect line and all interconnected alarms will sound. The MCP401RC switch element can be reset using

the plastic key supplied.

PLEASE NOTE:The MCP401RC is designed for use with the following models of Smoke/Heat/CO Alarms

- Ei161RC, 164RC, 166RC, 141, 144, 146, 151TL, 154TL, 156TLH, 2110, 261ENRC, 261DENRC.

WARNING: This Manual Call Point should be installed by a qualified electrician in accordance with the

Requirements for Electrical Installations published by the Institute of Electrical Engineers (BS7671 current edition).

A maximum of 4 MCP401RC units can be installed on one system in addition to 12 interconnect alarms.

B16073-R2-MCP401RC-UC-ENG 14/10/08 4:24 PM Page 1

P/N B16073 Rev 2

Testing

It is recommended that the MCP401RC is tested directly after installation and then at least monthly.

Test that the MCP401RC call point triggers the alarm(s) by pressing the black spot on the front cover. A

striped warning indicator should drop down into view on the front face (visible through the clear plastic

window). Check that each alarm in the system is sounding.

Reset the MCP401RC by following the instructions in the Resetting section below. The alarms should stop

sounding.

Now turn off the mains power to the system. Repeat the test above (this checks the rechargeable back-up

in the unit). Reinstate the mains power to the system. The MCP401RC will operate in standby with mains

off for over 6 months. With the Manual Call Point triggered it can give an alarm signal for over 16 hours.

The crossed out wheelie bin symbol that is on your

product indicates that this product should not be disposed

of via the normal household waste stream. Proper

disposal will prevent possible harm to the environment or

to human health. When disposing of this product please

separate it from other waste streams to ensure that it can

be recycled in an environmentally sound manner. For

more details on collection and proper disposal, please

contact your local government office or the retailer where

you purchased this product.

Aico Ltd. Mile End Business Park,

Maesbury Rd, Oswestry,

Shropshire, SY10 8NN, U.K.

Tel: 0870 7584000 www.aico.co.uk

Ei Electronics. Shannon, Ireland.

Tel: +353 (0)61 471277 www.eielectronics.com

Connect the wiring as shown in Figures 2 & 3 previously. Note: the Earth connection is for convenient

termination of the earth conductor and is not required for the safety of the unit. The wiring should be

installed securely (e.g. tie wrap together) to prevent a hazard if one becomes detached.

Carefully slide the front cover and circuit board diagonally into the mounting box, top section first (see Figure 4).

Then carefully locate the top of the front cover onto the top of the wall plate and hinge down to snap

securely in place (see Figure 5).

Reconnect the AC mains power to the circuit and check that the green mains indicator lights on the

Smoke/Heat/CO Alarms are on.

Figure 4 Figure 5

To reset the unit, insert the

reset key into the hole in the

bottom of the front cover. The

striped warning indicator

should disappear. With the key

still inserted, twist it anti-

clockwise until the operating

element clicks back into place,

then remove the reset key (see

Figure 6).

Figure 6 Figure 7

To detach the front cover,

remove the security screw and

insert the reset key into the

bottom of the cover. With the

key firmly inserted, hinge the

bottom of the cover away from

the wall plate/ mounting box

(the reverse motion to fitting).

See Figure 7.

Resetting Opening Unit / Removal

B16073-R2-MCP401RC-UC-ENG 14/10/08 4:24 PM Page 2

Table des matières

Autres manuels Ei Electronics Détecteur de fumée

Ei Electronics

Ei Electronics Ei603MRF Manuel utilisateur

Ei Electronics

Ei Electronics Ei405TY RF Optical Manuel utilisateur

Ei Electronics

Ei Electronics Ei 405C Manuel

Ei Electronics

Ei Electronics Ei Ei168RC Manuel utilisateur

Ei Electronics

Ei Electronics EiA600 Series Manuel utilisateur

Ei Electronics

Ei Electronics Ei 105C Optical Manuel utilisateur

Ei Electronics

Ei Electronics EI129 Manuel utilisateur

Ei Electronics

Ei Electronics Ei160e Series Manuel utilisateur

Ei Electronics

Ei Electronics Ei3105RF Optical Manuel utilisateur

Ei Electronics

Ei Electronics Ei151TL Instructions d'installation

Ei Electronics

Ei Electronics Ei3024 Manuel utilisateur

Ei Electronics

Ei Electronics Easichange Series Manuel utilisateur

Ei Electronics

Ei Electronics EIB140RC Series Manuel utilisateur

Ei Electronics

Ei Electronics B16009-R0-160RC Series Manuel utilisateur

Ei Electronics

Ei Electronics Ei161e Manuel utilisateur

Ei Electronics

Ei Electronics EI 100B Standard Manuel

Ei Electronics

Ei Electronics Ei140e Series Manuel utilisateur

Ei Electronics

Ei Electronics Ei 151TLR Ionisation Manuel utilisateur

Ei Electronics

Ei Electronics Ei141 Ionisation Manuel utilisateur

Ei Electronics

Ei Electronics aico Ei146e Manuel utilisateur

Ei Electronics

Ei Electronics EI 100L Emergency Light Manuel utilisateur

Ei Electronics

Ei Electronics Ei 105B Manuel utilisateur

Ei Electronics

Ei Electronics Ei 169 Manuel utilisateur

Ei Electronics

Ei Electronics Ei 156TLR Optical Manuel utilisateur

Manuels Détecteur de fumée populaires d'autres marques

x-sense

x-sense SD19-W Manuel utilisateur

BRK electronic

BRK electronic First Alert P1010 Manuel utilisateur

FireAngel

FireAngel Thermoptek ST-622 Manuel utilisateur

teko

teko Astra-42A Manuel utilisateur

Safetec

Safetec SDS-2/6 Manuel du propriétaire

Siemens

Siemens PE-11C Manuel utilisateur

System Sensor

System Sensor DH500ACDC Manuel utilisateur

Resolution Products

Resolution Products RE612 CryptiX Manuel utilisateur

First Alert

First Alert PC900V Manuel utilisateur

Eminent

Eminent EM6590 E-Domotica Manuel utilisateur

Carrier

Carrier Kidde Quell Q301 Manuel utilisateur

VESDA

VESDA VLF-500 Manuel utilisateur

ELRO

ELRO FS8110 Manuel utilisateur

Heiman

Heiman SMOKI NS-626PHS Manuel utilisateur

Regin

Regin SDD-S65 Manuel utilisateur

Family Gard

Family Gard FG225 Manuel utilisateur

Greystone

Greystone DSD120 Manuel utilisateur

Aparton

Aparton ASD-10 Manuel utilisateur