Edimax GS-5654LX Manuel utilisateur
GS-5654LX & GS-5654PLX
Quick Installation Guide
05-2021 / v1.0
Contents
IProduct Information.................................................1
I-1 Package Content...............................................................2
I-2 Hardware Overview .........................................................3
I-3 LED Status.......................................................................5
II Installation ..............................................................7
II-1 Mounting the Switch ........................................................7
II-1-1 Placement Tips ........................................................7
II-1-2 Rack Mounting ........................................................8
III Getting Started ......................................................10
III-1 Power.............................................................................10
III-1-1 Connecting to Power ............................................10
III-1-2 Connecting to Network.........................................11
III-1-3 Starting the Web-based Configuration Utility .......11
1
IProduct Information
The EDIMAX Pro GS-5654LX and GS-5654PLX fully utilizes the power of your
office networking for demanding tasks, such as data backup, video
conferencing, high volume transaction processing, large file transferring, and
more.
With smart features such as SNMP v1/v2/v3, PoE PD Alive Check, DHCP
Snooping, QoS, CoS, STP, 802.1Q VLAN, IPv4/IPv6, Port Trunking, IGMP
v1/v2/v3 Snooping and Port Mirroring, the EDIMAX Pro GS- 5654LX web smart
switch provides a cost-effective, reliable, scalable and secure switch solution
for SMB networks.
You can find all supporting documents from the link below or via QR Code:
https://www.edimax.com/download
(Once you’ve visited the Edimax official website, please enter the model no.
“GS-5654LX or GS-5654PLX”into the search box to search for your product.)
2
I-1 Package Content
Before start using this product, please check if there is anything missing in the
package, and contact your dealer to claim the missing item(s):
GS-5408PLG V2
Power Cord
Rack-Mount Kit & Screws
GS-5654LX or
GS-5654LX or GS-5654PLX
QIG
Console Cable
3
I-2 Hardware Overview
GS-5654LX:
No.
Descriptions
1
Reset Button
2
LED (PWR)
3
LED (SYS)
4
LED (SYS ALM)
5
PoE Ports (1~48)
6
SFP+ Port (49~54)
7
Fan
8
Console Port
9
Power Jack
1
2
5
4
3
6
7
8
9
4
GS-5654PLX:
No.
Descriptions
1
Reset Button
2
LED (PWR)
3
LED (SYS)
4
LED (PoE MAX)
5
LED (SYS ALM)
6
PoE Ports (1~48)
7
SFP+ Port (49~52)
8
LED (Link/Act)
9
LED Slide Switch ( Link or PoE Powered)
10
Console Port
11
Power Jack
1
2
4
3
5
6
7
8
9
10
11
5
I-3 LED Status
GS-5654LX:
Function
Status
Description
PWR
On (Green)
Power on
Off
Power off
SYS ALM
On (RED)
System failure (Overheat, wrong voltage)
Off
Device in good condition
SYS
On (Green)
Power on
Off
Power off
Blinking (Green)
System boot up
Link/ACT
(1-48 port)
On (Green)
Link at 1000M
Blinking (Green)
Sending or receiving data
On (Amber)
Link at 10/100M
Blinking (Amber)
Sending or receiving data
Off
Port disconnected or link fail
SPF+
(49-54 port)
On (Green)
Link at 1000Mbps
On (Blue)
Link at 10Gbps
Blinking
(Green or Blue)
Sending data
Off
Port disconnected or link fail
6
GS-5654PLX:
Function
Status
Description
PWR
On (Green)
Power on
Off
Power off
SYS ALM
On (RED)
System failure (Overheat, wrong voltage)
Off
Device in good condition
SYS
On (Green)
Power on
Off
Power off
Blinking (Green)
System boot up
PoE Max
On (Green)
Over PoE max power
Off
Not over PoE max power
Link/ACT
(1-48 port)
On (Green)
Link at 1000M
Blinking (Green)
Sending or receiving data
On (Amber)
Link at 10/100M
Blinking (Amber)
Sending or receiving data
Off
Port disconnected or link fail
SPF+
(49-54 port)
On (Green)
Link at 1000Mbps
On (Blue)
Link at 10Gbps
Blinking
(Green or Blue)
Sending data
Off
Port disconnected or link fail
LED
Slide Switch
Left (Link/Act)
LAN port connection status
Right (PoE)
PoE connection status
NOTE: LED Slide Switch: LAN Port status (Left side) or PoE status (Right side)
Left (Link/Act)
1-48 Port
On (Green)
Link at 1000M
Blinking (Green)
Sending or receiving data
On (Amber)
Link at 10/100M
Blinking (Amber)
Sending or receiving data
Right (PoE)
1-48 Port
On (Green)
Feeding power to PoE Devices
Off
PoE function is not active
Blinking (Green)
PoE Device required power supply over 30W
7
II Installation
This chapter describes how to install and connect your Edimax Switch. Read the
following topics and perform the procedures in the correct order. Incorrect
installation may cause damage to the product.
II-1 Mounting the Switch
There are two ways to physically set up the switch.
Place the switch on a flat surface. To place the switch on a desktop, install
the four rubber feet (included) on the bottom of the switch.
Mount the switch in a standard rack (1 rack unit high).
II-1-1 Placement Tips
Ambient Temperature —To prevent the switch from overheating, do not
operate it in an area that exceeds an ambient temperature of 122°F (50°C).
Air Flow —Be sure that there is adequate air flow around the switch.
Mechanical Loading —Be sure that the switch is level and stable to avoid
any hazardous conditions.
Circuit Overloading —Adding the switch to the power outlet must not
overload that circuit.
Follow these guidelines to install the switch securely.
Put the switch in a stable place such as a desktop, to avoid it falling.
Ensure the switch works in the proper AC input range and matches the
voltage labeled.
Ensure there is proper heat dissipation from and adequate ventilation
around the switch.
Ensure the switch’s location can support the weight of the switch and its
accessories.
Figure 4 - Desktop Installation
8
II-1-2 Rack Mounting
You can mount the switch in any standard size, 19-inch (about 48 cm) wide rack.
The switch requires 1 rack unit (RU) of space, which is 1.75 inches (44.45 mm)
high.
For stability, load the rack from the bottom to the top, with the heaviest
devices on the bottom. A top-heavy rack is likely to be unstable and may tip
over.
When mounting smaller switch products into a standard 19-inch rack, a pair of
extension brackets (sometimes referred to as ears) are needed to adapt the
switch to the rack size.
These extension brackets are mounted on the switch using the screws provided
in the kit, and have two holes that are used to then screw the switch into the
rack.
An example of one type of these extension brackets is shown in the following
figure.
A common problem that occurs during rack mounting is the distance between
the screw holes on the rack. Some racks are made with a uniform distance
between all of the holes, and others have the holes organized into groups (see
photo on the next page for an example).
When organized into groups, the switch must be placed in the rack so that the
holes in the extension brackets line up correctly.
1. Align the mounting brackets with the mounting holes on the switch’s side
panels and secure the brackets with the screws provided.
Figure 5 - Bracket Installation
Autres manuels pour GS-5654LX
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Edimax Changer
Edimax
Edimax EU-HB4S Manuel utilisateur
Edimax
Edimax EU-PC2C Manuel utilisateur
Edimax
Edimax GS-1016 Manuel utilisateur
Edimax
Edimax GS-1008P Manuel utilisateur
Edimax
Edimax EK-16RE Manuel utilisateur
Edimax
Edimax EK-08RE Guide de référence
Edimax
Edimax ES-5824PHG Manuel utilisateur
Edimax
Edimax EK-2U2C Manuel utilisateur
Edimax
Edimax GS-1026 Manuel utilisateur
Edimax
Edimax ES-1008P Manuel utilisateur
Edimax
Edimax Rackmount Fast Ethernet Switch Manuel utilisateur
Edimax
Edimax GS-5424PLG Guide de configuration
Edimax
Edimax EK-PAK2 Guide de référence
Edimax
Edimax PS-3101P Manuel utilisateur
Edimax
Edimax 24 10 Manuel utilisateur
Edimax
Edimax ER-5398S Manuel utilisateur
Edimax
Edimax ES-3116P Manuel utilisateur
Edimax
Edimax 9-Port Desktop Ethernet Hub ER-5390S Manuel utilisateur
Edimax
Edimax EK-PS2C Guide de référence
Edimax
Edimax GS-5008E Manuel utilisateur
