Edimax EN-9230TX-64 Manuel utilisateur

10/100/1000Mbps PCI

Gigabit Ethernet Adapter

User’s Manual

Gigabit Ethernet Adapter

EN-9230TX-64/32

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply

with the limits of a Class B computing devices,

pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications.

If you suspect this product is causing interference, turn

your computer on and off while your radio or TV is

showing interference. If the interference disappears

then when you turn the computer off and reappears then

you turn the computer on, something in the computer is

causing interference.

You can try to correct the interference by one or more

of the following measures :

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment and

receiver.

3. Connect the equipment into an outlet on a circuit

difference from that to which the receiver is

connected.

4. Ensure that all expansion slots (on the back or side

of the computer) are covered. Also ensure that all

metal retaining brackets are tightly attached to the

computer.

1Introduction

Thanks you for purchasing our Gigabit Ethernet Adapter.

This guide is to provide the installation and usage of this

adapter for network installers and users. The Gigabit

network adapter complies to 64-/32-bit (EN-9230TX-32

supports 32-bit only) PCI specification and supports half-

/full- duplex feature which can double network speed.

This adapter supports 1000Mbps(Gigabit), 100Mbps and

10Mbps network speed, 1000BaseT operates on all four

pairs of category 5 UTP cable, 100BaseTX operates on

two pairs of category 5 UTP cable and 10BaseT operates

on Category 3, 4 or 5 UTP cable.

With the Auto-Negotiation technology, network speed is

auto detected. When you connect the adapter to Gigabit

Switch or another Gigabit NIC, the speed will be doubled

to 2000Mbps (1000Mbps Transmit and 1000Mbps

Receive). If you connect the adapter to 100BaseTX hub,

the network speed is 100Mbps. Similarly, if the hub is a

switching hub which supports full duplex function, then

the speed will be doubled to 200Mbps.

This adapter supplies many drivers including NDIS 4, 5

driver for Microsoft Windows 98SE, Me, NT, 2000, XP,

Netware Server 5.x, Netware ODI for DOS, Linux and

Unix. Whatever your requirements are ease of

installation, superior performance or responsive support

backed up by unlimited technical support, this adapter is

the superior choice.

2Features & Specifications

(1) Features & Benefits

ySupports 64-/32-bit (EN-9230TX-32 supports 32-bit

only), 66/33MHz PCI Local Bus Master Version 2.2/2.1.

yComplies with the IEEE 802.3, IEEE 802.3u, IEEE

802.3ab, IEEE 802.3x.

ySupports IEEE 802.3x full duplex flow control.

ySupports IEEE 802.1Q VLAN tagging.

ySupports PCI 2.1 Wake On LAN function.

yPlug and Play installation, auto-setup IRQ and I/O

address.

yAuto-Negotiation, full-/half- duplex.

ySupports Web-based Management.

yProvide three LEDs to indicate network link/activity and

10/100/1000Mbps connections.

(2) Technical Specification

yTopology : Star

yConnector : RJ-45

yStandard : IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX

IEEE 802.3ab 1000BaseT

yTransmission Rate : 10Mbps/20Mbps

100Mbps/200Mbps

1000Mbps/2000Mbps

yHardware Required : IBM compatible PC with

available PCI slot

(PCI 2.2/2.1), 64-/32-bit,

66/33MHz

yIRQ Line : Assigned by system

yI/O Address : Assigned by system

yDrivers : Windows 98SE/Me/NT/2000/XP,

Netware Server 5.x,

Netware ODI for DOS,

Linux and Unix

yLEDs : 10Mbps Link/Activity

100Mbps Link/Activity

1000Mbps Link/Activity

yTemperature : 32-131℉(0-55℃)

yHumidity : 10% to 95% (Non-condensing)

yCertification : FCC Class B, CE Mark, C-tick

yDimension : 163 x 64 mm (EN-9230TX-64)

144 x 63 mm (EN-9230TX-32)

yWeight : 81g (EN-9230TX-64)

76g (EN-9230TX-32)

3Installation

(1) Hardware Installation

To insert the network adapter into your PC, follow the

steps as below :

1. Turn off the computer and remove its cover.

2. Insert the adapter into a PCI slot.

3. Secure this adapter to the rear of the computer

chassis and put back the computer cover.

4. Connect the adapter to the network using twisted-

pair cable.

(2) Driver Installation

Use the drivers supplied by the diskette included in this

product. For detail description, please execute the

readme.exe in the root directory of the diskette

provided by this product.

(3) Hardware Installation for Wake On LAN

This card supports PCI 2.1 Wake On LAN function.

Please refer to following instructions for installation of

Wake On LAN.

A. Hardware Requirement for Wake On LAN

yIf your motherboard supports the PCI 2.1 only, then

the motherboard must provide a 3-pin WOL

connector. (Some computers may require you to

change a setting in your computer’s BIOS or setup

program to enable the WOL feature.)

•ATX 2.01 power supply.

Note : Please installs only one active WOL adapter per

computer. You can install additional non-WOL

adapters.

(3) Hardware Installation for Wake On LAN

Please follow the next procedure to install the WOL

adapter to PCI 2.1 motherboard.

1. Unpack the 3-pin auxiliary power cable.

2. Insert the 3-pin auxiliary power cable into the

connector on the adapter.

3. Attach the 3-pin auxiliary power cable to the

connector on the PC motherboard.

4Trouble-shooting

If you experience any problems with the adapter, please

make sure the appropriate driver is loaded, the proper

cable is connected to the adapter port and the

hub/switch complies with the adapter specification,

such as 10Mbps 10BaseT, 100Mbps 100BaseTX and

1000Mbps 1000BaseT, then check the LED.

The adapter provides three LEDs to indicate network

status.

10Mbps Link/Activity

The LED indicates if the 10Mbps UTP has been LINK

ok or not. When the light is OFF, it indicates that the

10Mbps UTP port has not been connected or LINK not

ok. When the light is ON, it indicates that the 10Mbps

UTP port LINK ok. When the light is BLINKING, it

indicates that there is traffic flow on the network which

the adapter is connected to.

100Mbps Link/Activity

The LED indicates if the 100Mbps UTP has been

LINK ok or not. When the light is OFF, it indicates

that the 100Mbps UTP port has not been connected or

LINK not ok. When the light is ON, it indicates that

the 100Mbps UTP port LINK ok. When the light is

BLINKING, it indicates that there is traffic flow on the

network which the adapter is connected to.

1000Mbps Link/Activity

The LED indicates if the 1000Mbps (Gigabit) UTP has

been LINK ok or not. When the light is OFF, it

indicates that the 1000Mbps UTP port has not been

connected or LINK not ok. When the light is ON, it

indicates that the 1000Mbps UTP port LINK ok. When

the light is BLINKING, it indicates that there is traffic

flow on the network which the adapter is connected to.

( Wake On LAN )

The PC can not boot up after installing the

adapter.

1. Remove the 3-pin cable from the PC connector.

2. Boot up the PC, run setup program to enable ACPI

or Wake On LAN.

3. Turn off the PC and reconnect the 3-pin cable to the

PC.

4. Boot up the PC again.

The PC does not boot up when a Magic

Packet or Wake Up Frame is sent.

1. Check the specification of this PC meets the

hardware requirement in Chapter 3.

2. Verify the BIOS setting of Wake On LAN is

configured properly. (Please check your computer

owner’s manual or contact your dealer for more

information.)

3. Remove the PC cover and check the 3-pin cable

connection.

4. If the adapter still does not wake up, install a known

good working Wake On LAN adapter and 3-pin

auxiliary power cable in the PC and recheck the PC.

[!] Contact your dealer if problem persist.

product. No part of this manual may be reproduced,

transcribed, stored in a retrieval system, translated into

any language or computer language without the prior

written consent of the manufacturer.

All brand and product names are trademarks and/or

registered trademarks of their respective companies.

TRADEMARKS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edimax Adaptateur

Edimax

Edimax Access Point Guide de l'utilisateur

Edimax

Edimax EU-4208 Manuel utilisateur

Edimax

Edimax EW-7608Pg Manuel utilisateur

Edimax

Edimax EN-9260TX-E Manuel utilisateur

Edimax

Edimax HP-5001 Manuel utilisateur

Edimax

Edimax EW?7711ULC Manuel utilisateur

Edimax

Edimax EW-7722UnD Manuel utilisateur

Edimax

Edimax EW-7612PIn Manuel utilisateur

Edimax

Edimax HP-5102 Manuel utilisateur

Edimax

Edimax EN-9120 Manuel utilisateur

Edimax

Edimax HP-6002AC Manuel utilisateur

Edimax

Edimax EW-7717Un Manuel utilisateur

Edimax

Edimax EW-7611UCB Manuel utilisateur

Edimax

Edimax EW-7811GLN 2.0A Manuel utilisateur

Edimax

Edimax EW-7612UAn V2 Manuel utilisateur

Edimax

Edimax EU-4308 Manuel utilisateur

Edimax

Edimax EU-4206 Manuel utilisateur

Edimax

Edimax EW-7618Ug Manuel utilisateur

Edimax

Edimax EU-4206 Manuel utilisateur

Edimax

Edimax HP-6002 Manuel utilisateur

Edimax

Edimax Edimax Wireless LAN Cardbus Adapter Manuel utilisateur

Edimax

Edimax HP-5102ACK Manuel utilisateur

Edimax

Edimax EN-9230TX-32 Manuel utilisateur

Edimax

Edimax EW-7811UAC Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur