Edgewater Networks EdgeMarc 6400LF2 Manuel utilisateur

Page 1 of 10

EdgeMarc 6400LF2

EdgeView 6400LF2

EdgeProtect 6400LF2

Quick Start Guide

Version 1.0

300-6400LF-001

Page 2 of 10

Before You Start

Please read this guide thoroughly as it describes the basic installation of

the device. Additional configuration that is needed to deploy the device in

a specific environment can be performed by using online help.

This guide also provides an example of a typical 6400LF2 deployment

that can be used as a guideline for your installation.

Requirements for Installation

•A computer with a web browser such as Microsoft Internet Explorer or

Netscape Navigator or any other browser of your choice

•At least one Ethernet cross-over cable

Page 3 of 10

Instructions

Step 1 −Connecting the Cables

Figure 1: 6400LF2 Back Panel

1. Connect one end of an Ethernet crossover cable to local LAN port 1 of 6400LF. This port

can be seen in area “B” of Figure 1: 6400LF2 Front Panel. Connect the other end of

the cable to your computer’s Ethernet port.

2. Connect the other end of the Ethernet crossover cable to a PC with a web browser.

3. If AC power supply modules are installed in the chassis, plug one end of the power

adapter into an AC outlet and the other end into the power receptacle on the 6400LF,

noted in area “A” of Figure 1: 6400LF2 Back Panel.

4. If DC power supply modules are installed in the chassis, complete the following steps *:

a) Turn off the DC power supply for the 6400LF2.

b) Attach the grounding cable to the corresponding terminal lug, located in area “A”

of Figure 1: 6400LF2 Back Panel.

Page 4 of 10

c) Connect the positive and negative cables to their corresponding terminals, also

located in area “A” of Figure 1: 6400LF2 Back Panel.

d) Turn on the DC power supply for the 6400LF2.

5. Turn the power switch “on”, as shown in area “A” of Figure 2: 6400LF2 Front Panel (see

the following page).

Figure 2: 6400LF2 Front Panel

a) To learn more about safety requirements and recommendations for AC and DC

power supplies, review “Power Supply Modules” in the 6400LF2 Hardware

Installation Guide .

Page 5 of 10

Page 6 of 10

Step 2 −Configuring the 6400LF2

You can configure the 6400LF2 EdgeMarc and 6400LF2 EdgeProtect appliances using

a simple web-based user interface. Configure the 6400LF2 EdgeView appliance using

YaST, a pre-installed, LINUX-based system management tool.

Configuring the 6400LF2 EdgeMarc and 6400LF2 EdgeProtect

You can configure the 6400LF2 EdgeMarc and 6400LF2 EdgeProtect appliance using a web

browser such as Internet Explorer or Netscape Navigator. The 6400LF2 is shipped with the

pre-configured IP address 192.168.1.1 for the LAN port .

Requirement: To connect a PC directly to the appliance, you must use an ethernet

crossover cable.

To connect to the 6400LF2 EdgeMarc and 6400LF2 EdgeProtect, follow these steps:

1. Assign static IP address 192.168.1.2 with subnet 255.255.255.0 to a PC

2. Connect the PC to LAN port 2 (also labeled as NIC2) of the 6400LF2 using the ethernet

crossover cable

3. Launch a web browser on the PC and enter the URL string: 192.168.1.1. Press Return

The login window appears

4. Enter the username root and the password default to log into the system

The initial 6400LF2 main configuration menu appears

Page 7 of 10

5. Select Network and start configuring the 6400LF2 appliance.

Note

For secure network management on an EdgeMarc or EdgeProtect 6400LF2 appliance,

change the default user name and password as described in the VOS for EdgeMarc User

Manual.

Configuring the 6400LF2 EdgeView

You can configure the 6400LF2 Edgeview appliance using YaST, a pre-installed,

LINUX-based system management tool. Access YaST from the command line

interface of the EdgeView appliance.

To connect to the 6400LF2 Edgeview appliance, follow these steps:

1. Connect a PC with a cross-over Ethernet cable to Port 1 of the EdgeView

chassis.

2. Since Port 1 is 192.168.1.1, configure your PC to have the IP address of

192.168.1.2, subnet mask of 255.255.255.0 and default gateway of 192.168.1.1.

3. Make sure you can ping 192.168.1.1 from your PC.

4. Open your favorite SSH application on your PC and SSH to the EdgeView.

(Note: The new LF chassis only accept SSH v2. In PuTTY, go to the SSH tab on

the left and under Preferred SSH Protocol Version, select 2)

5. Log into the CLI.

6. Type ‘yast’ at the # prompt. The configuration page appears as follows:

Page 8 of 10

7. Continue to configure the EdgeView appliance as described in “Chapter 2.

Getting Started” of the EdgeView 6400 User Manual.

Page 9 of 10

Step 3 −Plan Your Configuration

The EdgeMarc 6400LF2 can be deployed as a gateway router in a network. It can also be

deployed in a network behind an existing firewall. Based on your deployment criteria, consult

the following documents for further configuration:

•6400LF2 EdgeMarc Hardware Installation Guide

•VoIP Operating System (VOS) for EdgeMarc User Manual

Helpful Hints

Although not recommended, the EdgeMarc 6400LF2 and IP phones can be installed behind an

existing enterprise firewall. In this instance the firewall will have to be configured to allow access

to and from the EdgeMarc 6400LF’s public IP address for the following ports:

Port Type

Firewall Ports to Open

UDP

161 (SNMP) and 162 (SNMPTRAP)

RTP

1056 to 1255

TCP

SSH TCP 22 for remote management & TCP 80 for WAN

configuration-downloads

Telnet

FTP

TCP 21 for stateful TCP-session control from 6400LF2 to

Edgewater FTP server

MGCP

2427, 2429, 2432, and 2727

NTP ¬

123

SIP

5060 and 5075

IP phones normally point to a local NTP server for their time reference. The NTP port 123

needs to be opened if your network does not have an NTP server.

Please Note: Traffic shaping for this configuration is only available if the enterprise data

devices are also installed behind the 6400LF2 appliance.

Page 10 of 10

The web page configurations for the various 6400LF2 deployments are shown below. The two darker-

shaded rows indicate the minimum configuration required for each deployment.

6400LF2

GUI Configuration

Page

6400LF2 as

Gateway

Router

6400LF2 within existing

infrastructure

6400LF2 behind an

existing firewall

Network

Yes

VoIP/ALG

Yes

NAT

Yes

Optional

Yes

Firewall

Yes

Optional, but

recommended

Optional, but

recommended

DHCP

Yes

Yes (but should be

disabled if DHCP server

already exists)

Yes (but should be

disabled if DHCP server

already exists)

Traffic Shaper

Yes

Optional (depends on

network topology)

Traffic Simulator

Only for

testing

Only for testing

System

As needed

Please visit our website at www.edgewaternetworks.com or contact the Edgewater Technical

Assistance Center at 408.351.7255 for additional information or assistance.

Edgewater Networks, Inc.

2895 Northwestern Parkway

Santa Clara, CA 95051

Phone: (408) 351-7200

[email protected]

Converged Networking. Simplified.

Autres manuels pour EdgeMarc 6400LF2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edgewater Networks Porte

Edgewater Networks

Edgewater Networks ATT110900764 Manuel de la liste des pièces

Edgewater Networks

Edgewater Networks 200AE1 Manuel utilisateur

Edgewater Networks

Edgewater Networks EdgeMarc 4552 Manuel utilisateur

Edgewater Networks

Edgewater Networks 4610W Manuel

Edgewater Networks

Edgewater Networks EdgeMarc 4550 Manuel utilisateur

Edgewater Networks

Edgewater Networks 4610W Manuel utilisateur

Edgewater Networks

Edgewater Networks EdgeMarc 250W Manuel

Edgewater Networks

Edgewater Networks 200AE1 Manuel utilisateur

Edgewater Networks

Edgewater Networks EdgeMarc 250W Manuel utilisateur

Edgewater Networks

Edgewater Networks EdgeMarc 4550 Manuel

Edgewater Networks

Edgewater Networks EdgeMarc 250W Manuel utilisateur

Edgewater Networks

Edgewater Networks 200AE2 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur