Edelbrock 68512 Manuel utilisateur

Rev. 5/06 - DA/mc Catalog #68512, #68513

Brochure #63-68512

Page 1 of 2

SHORTY HEADER

for 1987-1991 Dodge Dakota Truck (All),

3.9L V6 Engine

Catalog #68512, #68513

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before installing your new Shorty Header. If you have any questions, please call

our Technical Hotline at: 1-800-416-8628 from 7:00 am - 5:00 pm, Monday-Friday, Pacific Standard Time or e-mail

us at [email protected]. Please fill out and mail your warranty card.

HEADERS: These components are designed to improve the exhaust efficiency of the Dodge 3.9 Litre V6 engine with E.F.I.

(Electronic Fuel Injection). These tubular manifolds are a direct replacement for the factory exhaust manifolds. A

performance gain can be expected by the installation of this system. This system does not require welding for installation

and retains all O.E.M. emissions equipment.

SUGGESTED TOOLS FOR INSTALLATION:

❑3/8" ratchet socket set with extensions and sockets ❑Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Combination set of open-end wrenches ❑Liquid penetrant, anti-seize compound

SPECIAL NOTICE: This Edelbrock part has received an Executive Order (E.O. #) from the California Air Resources Board

(C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions

equipment certification, we have included a silver fan shroud decal to help testing personnel verify that this part is a legal

replacement part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your fan shroud

next to the existing emission and engine specification decal. Do not cover your original equipment specification decal with

the Edelbrock fan shroud decal.

WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your

headers. Those products can cause excessive heat and moisture buildup resulting in corrosion and early

failure of the system.

NOTE: High temperature spark plug wires and boots are recommended to withstand heat from Headers.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

HARDWARE SUPPLIED

Catalog #68512 (Ceramic-Coated), #68513 (Ti-Tech Coated)

Qty.Description Qty.Description

❑1 #25-9275 Header left side (#68512) ❑2 Hex nuts; 5/16” - 24

❑1 #25-9276 Header right side (#68512) ❑4 Hex nuts; 3/8” - 16 (plated)

❑1 #25-9020 Header left side (#68513)

❑2 Hex nuts; 10-32

❑1 #25-9021 Header right side (#68513)

❑1 Band clamp; 1-1/2”

❑4 Hex bolts; 3/8” - 16 x 2” ❑2 Star washers; 3/16” (internal)

❑2 Manifold gaskets ❑1 Round head screw; 10-32 x 1-3/4”

❑1 Heat stove plate ❑ 2 Studs; 5/16” x 1-1/2”

❑1 Hex cap screw; 10-32 x 1/2” ❑2 Lockwashers; 5/16”

❑1 Flat washer; 3/16” ❑4 Lockwashers; 3/8”

Rev. 5/06 - DA/mc Catalog #68512, #68513

Brochure #63-68512

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: (800) 416-8628

Office: (310) 781-2222

E-Mail: [email protected]

• DISASSEMBLY

1. Disconnect negative cable from battery.

2. Use penetrating oil on all nuts and bolts to be

removed. This will prevent the possibility of

broken or stripped nuts and bolts.

3. Remove O2 sensor (1987 only) being careful

not to rupture or destroy the unit. WARNING:

Do not clean this unit in any solvent and do not

damage wire.

4. Unbolt air injection tubes from both manifolds.

5. Unbolt exhaust pipes from both exhaust

manifolds.

6. Unbolt and remove both exhaust manifolds.

7. Install 5/16"x 1-1/8" studs (supplied) in second

hole on left side and third hole on right side

(where OEM bolts were located on exhaust

manifolds).

8. Clean and inspect all sealing surfaces before

assembly.

• ASSEMBLY - LEFT SIDE

1. Place manifold port gasket over studs (be sure

surface is clean).

2. Install TES manifold over studs, install OEM cup

washers, nuts and additional nut provided in

kit, then tighten evenly.

3. Bolt air injection tube to manifold using OEM

gasket (do not tighten at this time).

4. Bolt exhaust pipe to TES manifold using 3/8" x

2" bolts, nuts, and lock washers provided in kit

(do not tighten at this time).

5. Install O2 sensor using anti-seize on threads

and torque to 30 ft./lbs.

• ASSEMBLY - RIGHT SIDE

1. Place heat stove plate on top of TES manifold,

insert 1-3/4" long round head screw through

plate and down between front primary tubes

adjacent to port flange. Place 3/16" flat

washer and lock washer over screw, then start

nut (do not tighten at this time).

2. Place band clamp over rear primary tube at the

front and attach to heat stove using 3/16" bolt,

lock washer, and nut provided in kit. Secure

heat stove plate at this time.

3. Rubber mud guard attached to fender well

must be trimmed to clear TES manifold tubes.

4. Remove the manifold and trim the necessary

material from the mud guard.

5. Place manifold port gasket over studs (be sure

surface is clean).

6. Install TES manifold over studs; install OEM cup

washers, nuts, and additional nut provided in

kit, then tighten evenly.

7. Bolt air injection tube to manifold using OEM

gasket and tighten both sides at this time.

8. Bolt exhaust pipe to manifold using 3/8" x 2"

bolts, nuts, and lock washers provided in kit.

9. Tighten both right and left side exhaust pipe

connections.

10. Connect negative cable to battery.

11. Be sure that all brake and fuel lines have

adequate clearance.

12 Start engine and bring up to normal running

temperature, then turn off and let cool.

13. When cool, re-tighten all manifold nuts and

bolts.

INSTALLATION INSTRUCTIONS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 66722 Manuel utilisateur

Edelbrock

Edelbrock 68722 Manuel utilisateur

Edelbrock

Edelbrock 396-502 Manuel utilisateur

Edelbrock

Edelbrock Super Victor Race Manifold 2928 Manuel utilisateur

Edelbrock

Edelbrock 6009 Manuel utilisateur

Edelbrock

Edelbrock 63-0081 Manuel utilisateur

Edelbrock

Edelbrock 4737 Manuel utilisateur

Edelbrock

Edelbrock Performer 70011 Manuel technique

Edelbrock

Edelbrock 65022 Manuel utilisateur

Edelbrock

Edelbrock QwikData 91001 Manuel utilisateur

Edelbrock

Edelbrock E-TEC 170 Manuel utilisateur

Edelbrock

Edelbrock 7798 Manuel utilisateur

Edelbrock

Edelbrock Performer-Plus 2201 Manuel utilisateur

Edelbrock

Edelbrock 65063 Manuel utilisateur

Edelbrock

Edelbrock 262-400 Manuel utilisateur

Edelbrock

Edelbrock Cat-Back Exhaust System 5714 Manuel utilisateur

Edelbrock

Edelbrock 5223 Manuel utilisateur

Edelbrock

Edelbrock 5276 Manuel utilisateur

Edelbrock

Edelbrock 65232 Manuel utilisateur

Edelbrock

Edelbrock 2828 Manuel utilisateur

Edelbrock

Edelbrock 70405 Manuel utilisateur

Edelbrock

Edelbrock 305 Manuel d'instructions

Edelbrock

Edelbrock 72961 Manuel utilisateur

Edelbrock

Edelbrock 6879 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur