Edelbrock 33505 Manuel utilisateur

INSTALLATION INSTRUCTIONS

FOR 1996-2001 VIPER SHOCKS

Catalog #33505

§Please read these instructions entirely before beginning. Proper installation is a must to realize the

maximum performance improvements.

IMPORTANT NOTES:

§Upon initial inspection, some new shocks may have a small amount of oil in the area of the seal. This is a

normal occurrence following manufacture and does not indicate a problem with your shocks.

§Any time you are working under a vehicle, be sure to use the proper jack stands and tire chocks to prevent

any shifting or slipping of the car. Never use a jack only to support the vehicle while changing shocks.

§Inspect shock brackets or mounting points before installation to make sure they are not broken or bent.

§Do not attempt to disassemble these shocks. Return damaged shocks to Edelbrock for any necessary

service or repairs. INSTALLATION

Step 1 Support Viper by frame with jack stands or

on a lift.

Step 2 Remove all four wheels.

Step 3 Removal of front shocks:

Fig. 2

An aluminum block should be placed between arm and

hammer to minimize marking control arm, do not hammer

directly on the arm. It should only require a couple of

sharp taps with a hammer in order to pop from seat. Do

both left and right sides, and remove nuts.

3(a) Loosen upper and lower shock nuts, but do not

remove the bolts at this time. (see Fig. 1).

3(b) If the lower shock nut is to rear, the lower sway

bar end link must be removed in order for the

bolt to have enough clearance for removal.

(see Fig. 1).

Fig. 1

3(c) Removal of lower sway bar endlink

If the tool for unseating the sway bar from the

lower control arm is not available, the following

procedure can be used. (The sway bar end

link is held in place with a tapered seat). In

order to remove:

3(c)1 Loosen lower sway bar end link nut, do

not remove completely

3(c)2 Place jack under the nut

3(c)3 Jack up and apply pressure

3(c)4 Tap control arm with hammer

(see Fig. 2).

3(d) Remove upper and lower bolts to remove

shock. It may need a little gentle persuasion

with a pry bar (see Fig. 3). Bolt should come

out by hand.

Fig. 3

3(e) Shock may be removed through the top.

Step 4 Removal of rear shock Step 6 Disassembly of rear coil springs from shock

4(a) Loosen upper and lower nuts.

4(b) In order to remove bolts, they may need a little

gentle persuasion with a pry bar. Bolt should

come out by hand (see Fig. 3).

4(c) Shock will now come out through the top.

Step 5 Disassembly of front coil springs from

shocks

6(a) Compress coil spring (see Fig. 6).

6(b) Move bump rubber down in order to remove

spring seat retainer (see Fig. 6).

6(c) Release coil spring compressor carefully.

Fig. 6

A coil spring compressor is required to remove the

springs from shocks. All proper safety precautions must

be followed. Consult spring compressor manufacturer

recommended instructions before starting.

5(a) Compress coil spring (see Fig. 4).

Fig. 4

5(b) Move bump rubber up shaft in order to remove

spring seat retainer (see Fig. 5).

Fig. 5

5(c) Release coil spring compressor carefully.

Step 7 Assembly of IAS shocks (Note: Apply anti-

seize compound to threaded collars)

7(a) Adjust all four threaded spring collars

(see Fig. 7).

2 front topped out

2 rear = 5/8” from top of threaded

collar.

Fig. 7

Step 8 Assembly of Front shocks

8(a) Insert coil spring with flat ground end against

threaded collar seat .

7(b) Install and tighten allen set screw with 1/8 allen

wrench (see Fig. 8).

Fig. 8

8(b) Put shock and coil spring in spring

compressor (see Fig. 11).

Fig. 11

7(c ) Slide threaded collar onto shock. It should

seat against snap ring. Front shocks are

easily identified by short threads on the piston

rod (see Fig. 9).

Fig. 9

The rears have long threads on Piston rod

(see Fig. 10).

Fig. 10

8(c) Compress coil spring until lower seat has

enough clearance to install lower seat and

9/16 jamb nut (see Fig. 12).

Fig. 12

Step 9 Rear IAS shocks

IAS shock reuses the O.E.M. large black clevis mount

and must be unscrewed from the shock body.

9(a) Mount clevis in vice with soft jaws, aluminum

preferred as not to mark up the clevis.

Screw jamb nut by hand until it hard stops at end of

threads (see Fig. 13).

Fig. 13

8(d) Apply Loctite to threads, screw rod end on by

hand until it hard stops, tighten jamb nut against

rod end with 1” wrench on rod end using a 7/8”

crowfoot wrench torque nut to 70 ft lbs.

(see Fig. 14).

Fig. 14

8(e) After removing from spring compressor, make

sure spring fits correctly in lower spring pocket.

(see Fig. 15)

Fig. 15

9(b) Using supplied crowfoot wrench (see Fig. 16)

Fig. 16

(Top photo –spanner wrench )

(Bottom photo –crowfoot wrench)

loosen shock body from clevis with ½” drive breaker

bar and crowfoot wrench (see Fig. 17).

Fig. 17

(From the factory, the shock body was torqued to the

clevis with Loctite, so it will require a bit of effort to

remove).

9(c ) Once the clevis and shock body are apart, the

threads need to be cleaned to remove any

grease, Loctite or dirt (use brake cleaner or

parts wash), etc.

9(d) Install the threaded collar on to shock seating it

against snap ring on the IAS shock

(see Fig. 18).

9(e) Install short clevis adapter jamb nut with holes

up towards shock body (see Fig. 18).

9(f) Screw clevis adapter nut on piston rod by hand

until threads stop, install 9/16 jamb nut with

Loctite (see Fig. 18).

9(g) Clamp supplied spanner wrench (see Fig. 16) in

vise (see Fig. 18) to support threaded adapter

torque nut to 75 ft lbs. with 7/8 socket.

Fig. 18

9(i) Assemble shock by screwing the adapter with

Loctite applied into clevis (see Fig. 20),

Fig. 20

screw the adapter in clevis until it bottoms (see

Fig. 21), torque to 70 ft lbs. using same spanner

wrench (see Fig. 16).

Fig. 21

9(j) Screw the thin threaded adapter jamb nut with

Loctite applied until it bottoms and torque to 70-ft

lbs. with spanner wrench.

9(h) Clamp clevis in vise. Install spring on clevis

spring seat (see Fig. 19).

Fig. 19

Step 10 Installing IAS shocks

Reinstallation is reverse of removal.

10(a) Both front and rear may require a little gentle

persuasion with a long pry bar to push control

arms down in order to install bolts (see Fig. 22

and Fig. 22a). Do not torque nuts at this time.

Front lower bolts may be installed with nuts to

the front. This will make it easier for

reassembly.

Fig. 22

Fig. 22a

10(b) Front sway bar end links may now be

reinstalled. Install both left and right at the

same time. After both sides are in position, the

end link to control arm nuts can be torqued to

16 ft lbs.

10(c) Important: After all four shocks are installed,

place jack or jack stand under control arm –

support vehicle to load suspension at ride

height and torque bolts to:

Front (upper and lower) 80-100 ft. lbs.

Rear (upper) 80-100 ft. lbs.

Rear (lower) 130 ft. lbs.

This must be done to pre-load bushing for their

proper position in order for safe and proper

handling. This is a very important step.

10(d) Install and torque wheels to 90 ft. lbs. After

5-10 miles, re-torque wheels to 90 ft. lbs.

Parts List

Qty. Description Qty. Description

2 #33505 Front shock assemblies 1 Crowfoot wrench (for removal of shock from clevis)

2 #34505 Rear shock assemblies 1 Spanner wrench (for installing and torquing of rear

2 Rear rodend clevis adapters threaded clevis adapter and jamb nut)

2 Rear rodend clevis adapter locknuts 1 Loctite tube

4 Upper coilover spring perch 1 Anti-seize

4 Coilover threaded sleeves 1 Hardware kit

4 -set screws

4 -9/16 jam nuts

Enjoy the improved ride and handling from your new Edelbrock IAS shocks.

Edelbrock Corporation

2700 California Street

Torrance, California 90503

Office (310) 781-2222

Fax (310) 320-1187

Toll-Free Tech Line (800) 416-8628

Tech E-mail: [email protected]

PN 84-8152

2001 Edelbrock Corporation Revised 2/01

INSTALLATION INSTRUCTION

PROOFING FORM

Date: 2/20/01

From: Gary Nelson

To: Jack Mayberry

Part No./

Description: PN 33505 –Shocks for 1996-2001 Viper

Reviewed by: Date

Approved by: Date

No. of copies to be printed:

Received by: Date

F0505D

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 6879 Manuel utilisateur

Edelbrock

Edelbrock Performer 70070 Manuel utilisateur

Edelbrock

Edelbrock 4779 Manuel utilisateur

Edelbrock

Edelbrock 68003 Manuel utilisateur

Edelbrock

Edelbrock 70206 Manuel utilisateur

Edelbrock

Edelbrock 5056 Manuel utilisateur

Edelbrock

Edelbrock 5713 Manuel utilisateur

Edelbrock

Edelbrock 66162 Manuel utilisateur

Edelbrock

Edelbrock Performer 7162 Manuel utilisateur

Edelbrock

Edelbrock Victor Series 6570 Manuel utilisateur

Edelbrock

Edelbrock 1711 Manuel utilisateur

Edelbrock

Edelbrock Russell R08364 Manuel utilisateur

Edelbrock

Edelbrock 73802 Manuel utilisateur

Edelbrock

Edelbrock 1400 Manuel utilisateur

Edelbrock

Edelbrock 5724 Manuel utilisateur

Edelbrock

Edelbrock 72000 Manuel utilisateur

Edelbrock

Edelbrock Victor 77459 Manuel utilisateur

Edelbrock

Edelbrock Acura Integra 6737 Manuel utilisateur

Edelbrock

Edelbrock 72279 Manuel utilisateur

Edelbrock

Edelbrock 2114 Manuel utilisateur

Edelbrock

Edelbrock 71001 Manuel utilisateur

Edelbrock

Edelbrock 71852 Manuel utilisateur

Edelbrock

Edelbrock 63-0081 Manuel utilisateur

Edelbrock

Edelbrock 5778 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur