Edelbrock 2114 Manuel utilisateur

Page 1 of 2 Rev. 11/02

Brochure #63-0152

PERFORMER MANIFOLD

MODEL: Non-EGR for Chevrolet 90° V6, 4.3L Vortec

CATALOG #2114

INSTALLATION INSTRUCTIONS

•Please study these instructions carefully before installing your new manifold. If you have any questions or problems,

please call our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or

e-mail us at [email protected].

•EGR SYSTEM: This manifold will not accept stock EGR (exhaust gas recirculation) equipment. Not legal on pollution-

controlled motor vehicles.

•MANIFOLD: This manifold will not accept any O.E.M. carburetor systems. We suggest you use the carburetor listed in

the carburetor recommendations. This manifold was designed for street rod, off-road and marine applications.

•ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. Please review each part listed

in the Installation Items section of the Edelbrock catalog to decide whether more items are required for your specific vehicle

than are mentioned in these instructions.

•MARINE APPLICATIONS: This manifold has been designed to accept either MerCruiser or OMC waterneck housings

using the lateral bolt holes of the waterneck flange in the manifold. Because of carburetor interference, the use of a 1"

high divided carb spacer (such as Edelbrock #8714) may be necessary. Waterneck housings vary, so determine if spacer

is needed prior to installation. If marine carburetor #1409 is used, you must re-calibrate the carburetor with Calibration Kit

#1485. NOTE: Salt water will corrode coolant passageway of manifold and greatly shorten manifold service life.

•CARBURETOR RECOMMENDATIONS: Use only carburetors recommended. If parts required for installation are

unavailable locally, contact Edelbrock directly.

A - Carburetor will work with non-EGR (Exhaust Gas Recirculation) or pre-emission control system.

F - Use carb-to-manifold base gasket supplied with carb.

I - Carburetor has no provision for evaporative canister.

K - Carburetor requires #8008 or #8024 stud, nut and washer kit. Determine length needed before installation.

•GASKETS AND SEALANT

1. Use only original equipment intake gasket set GM #12529196 when installing this Edelbrock manifold. If the original

gasket is in good condition, it may be re-used.

2. Do not use any type of gasket sealer on intake gaskets. The rubber O-rings will seal without chemical sealers.

3. Eliminate the end seals. Use automotive grade RTV silicone instead. Apply a bead of sealant approximately 1/4" high

across the block end seal surface, overlapping the intake gasket at the four corners. This method eliminates end seal

slippage and deterioration.

CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION

Performer #1403 (500 cfm) A, F, I, K (for 4.3L only) (none)

Performer #1404 (500 cfm) A, F, I, K (for 4.3L only) (none)

Performer #1409 (600 cfm) A, F, I (for 4.3L Marine only) #1485 Calibration Kit for Marine Applications

Page 2 of 2 Rev. 11/02

Brochure #63-0152

7 3 2

148 5

Hole Chart

A= 3/8 C= 3/8-16

B= 1/2 D= 5/16-18

Fig. 1

Fig. 2

•MANIFOLD TORQUE - Apply Loctite 222 to the intake bolt threads. Carefully tighten the intake manifold bolts evenly until

the intake manifold has compressed the o-ring section of the gasket. Torque all of the manifold bolts in the sequence

shown in Figure 1 to 11 ft/lbs or 15.0 Nm.

•FIRING ORDER AND CYLINDER NUMBERING - For cylinder numbering and firing order, see Figure #2.

•FINAL TUNING

1. Due to design, the fuel / air mixture and cylinder charging are very efficient with Performer manifolds. Generally speaking,

the stock jetting for the recommended aftermarket carburetors will not need changing. Specific applications may show an

increase in power by enriching the secondary jetting .003 from the stock setting.

2. Installation of aftermarket headers, camshafts or both with an Edelbrock Performer manifold may lean carburetor

calibration. Should this condition occur, re-calibrate with a richer jet.

3. For maximum power, port-match the manifold to the heads.

•CAMSHAFT AND HEADERS

Performer manifolds are compatible with aftermarket camshafts and/or headers. Header Primary tube diameter should be

1-1/2” to 1-5/8”.

•PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the “Part #____”

space. Thank you.

Edelbrock Corporation

2700 California Street

Torrance, CA 90503

Tech Line: 1-800-416-8628

Tech Fax: 310-972-2730

E-Mail: [email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 5761 Manuel utilisateur

Edelbrock

Edelbrock 68642 Manuel utilisateur

Edelbrock

Edelbrock Performer 2261 Manuel utilisateur

Edelbrock

Edelbrock 4700 Manuel utilisateur

Edelbrock

Edelbrock Russell 694300 Manuel utilisateur

Edelbrock

Edelbrock 5682 Manuel utilisateur

Edelbrock

Edelbrock QwikData 91001 Manuel utilisateur

Edelbrock

Edelbrock 5756 Manuel utilisateur

Edelbrock

Edelbrock 2-R Manuel utilisateur

Edelbrock

Edelbrock 66022 Manuel utilisateur

Edelbrock

Edelbrock ENDURASHINE 63-0299 Manuel utilisateur

Edelbrock

Edelbrock 68572 Manuel utilisateur

Edelbrock

Edelbrock 5776 Manuel utilisateur

Edelbrock

Edelbrock 71922 Manuel utilisateur

Edelbrock

Edelbrock 65003 Manuel utilisateur

Edelbrock

Edelbrock Performer 3764 Manuel utilisateur

Edelbrock

Edelbrock 68832 (Ceramic-Coated) Manuel utilisateur

Edelbrock

Edelbrock Performer-Plus 2152 Manuel utilisateur

Edelbrock

Edelbrock 1472 Manuel utilisateur

Edelbrock

Edelbrock 2263 Manuel utilisateur

Edelbrock

Edelbrock 8135 Manuel utilisateur

Edelbrock

Edelbrock 3871 Manuel utilisateur

Edelbrock

Edelbrock 70403 Manuel utilisateur

Edelbrock

Edelbrock 5652 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur