ECS P4VXASD2+ Manuel utilisateur

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 5.0a

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment onto an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that

may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 5

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 24

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 36

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction................................................................................................ 1

Checklist.................................................................................................... 1

Standard Items................................................................................................. 1

Features .................................................................................................... 2

Choosing a Computer Case....................................................................... 3

Mainboard Components ............................................................................ 4

CHAPTER 2 5

Installing the Mainboard 5

Safety Precautions..................................................................................... 5

Quick Guide............................................................................................... 5

Installing the Mainboard in a Case............................................................. 6

Checking Jumper Settings......................................................................... 6

Setting Jumpers ............................................................................................... 6

Checking Jumper Settings ............................................................................... 7

Jumper Settings ............................................................................................... 7

Connecting Case Components.................................................................. 9

The Panel Connectors.................................................................................... 10

Installing Hardware.................................................................................. 12

Installing the Processor.................................................................................. 12

Installing Memory Modules .......................................................................... 15

Installing a Hard Disk Drive/CD-ROM......................................................... 16

Installing a Floppy Diskette Drive................................................................. 18

Installing Add-on Cards................................................................................. 18

Connecting Optional Devices........................................................................ 20

Connecting I/O Devices........................................................................... 22

External Connector Color Coding................................................................. 23

CHAPTER 3 24

Using BIOS 24

About the Setup Utility............................................................................. 24

The Standard Configuration........................................................................... 24

Entering the Setup Utility.............................................................................. 25

Using BIOS.............................................................................................. 26

Standard CMOS Features.............................................................................. 26

Advanced Setup Page.................................................................................... 27

Power Management Setup Page .................................................................... 29

PCI/Plug and Play Setup Page....................................................................... 31

Load Optimal Settings................................................................................... 32

iii

Load Best Performance Settings.................................................................... 32

Features Setup Page....................................................................................... 32

CPU PnP Setup Page..................................................................................... 34

Hardware Monitor Page................................................................................. 34

Change Password........................................................................................... 35

Exit................................................................................................................ 35

CHAPTER 4 錯誤! 尚未定義書籤。

Using the Mainboard Software 錯誤! 尚未定義書籤。

About the Software CD-ROM.....................................

錯誤

尚未定義書籤。

Auto-installing under Windows 98..............................

錯誤

尚未定義書籤。

Running Setup.............................................................錯誤! 尚未定義書籤。

Manual Installation.....................................................

錯誤

尚未定義書籤。

Utility Software Reference.........................................

錯誤

尚未定義書籤。

Introducing the Mainboard

Thank you for choosing this mainboard. This mainboard has a Socket-478

processor socket for Intel Pentium 4 type of processors supporting front side

bus (FSB) speeds up to 533 MHz.

This mainboard incorporates the VIA P4X333 Northbridge and

VT8235/8233A(CE) Southbridge chipsets that support AC 97 audio codec,

and provide Ultra DMA 33/66/100/133 function. If the VT8235 SB is installed,

the mainboard supports built-in USB 2.0 providing higher bandwidth, imple-

ments Universal Serial Bus Specification Revision 2.0 and is compliant with

UHCI 1.1 and EHCI 0.95; if the VT8233A(CE) SB, it doesn’t support USB2.0

and without LAN. This mainboard has four 32-bit PCI slots, one 4xAGP slot,

one CNR (Communications and Networking Riser) slot, and an onboard

10BaseT/100BaseTX Network interface (optional).

There is a full set of I/O ports including two PS/2 ports for mouse and key-

board, two serial ports, one parallel port, one MIDI/game port and maximum

six USB ports --two back-panel ports and onboard USB headers make four

extra USB ports by connecting the Extended USB Module to the mainboard.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• This User’s Manual

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• Software support CD

• One Retention Module

Processor • The PGA Socket 478

• Supports Intel Pentium 4 series CPUs

• Supports up to 533 MHz Front-Side Bus

Chipset The P4X333 Northbridge and VT8235 / 8233A(CE)

Southbridge in this chipset are in accordance with an innova-

tive and scalable architecture with proven reliability and

performance. Refer below for the combination and respective

details:

NB SB Function

P4X333 VT8235 Support 533 MHz FSB, Ultra

DMA ATA 133 and DDR333

P4X333 VT8233A(CE) Support 533 MHz FSB, Ultra

DMA ATA 133 and DDR333.

Without LAN and USB 2.0

• An advanced V-Link memory controller architecture

that provides the bandwidth up to 533 MB/s and per-

formance necessary for even the most demanding

Internet and 3D graphics

• Support for an 4xAGP interface providing vivid 3D

graphics and video performance

• An ATA 133 interface on the chipset, which helps

boost system performance by providing a high-speed

connection to ATA 133 Hard Disk Drives, delivering

maximum sustained data transfer rates of 133 MB/sec

Additional key features include support for six USB ports,

an AC 97 link for audio and modem, hardware monitoring,

and ACPI/OnNow power management.

Memory • The mainboard accommodates 2 DDR + 2 SDR 168 pin,

3.3V DIMM sockets with a total capacity of 1 GB system

memory

• Supports DDR up to 333MHz (enhanced) memory bus

AGP This mainboard includes a 4xAGP slot that provides four times

the bandwidth of the original AGP specification. AGP technol-

ogy provides a direct connection between the graphics sub-

system and memory so that the graphics do not have to com-

pete for processor time with other devices on the PCI bus.

AC’ 97 Audio

Codec

(VT1612A)

• Compliant with AC’97 2.1 specification

• Three Audio Jacks – Line-Out, Line-In and Microphone-In

• Sound Blaster, Sound Blaster Pro Compatible

• Digital I/O compatible with consumer mode S/PDIF

• Advanced power management support

Expansion

Options

• Four 32-bit PCI slots capable of Ultra DMA bus mastering

with transfer rates of 33/66/100/133 MB/sec

• An 4xAGP slot

• A CNR (Communications and Networking Riser) slot

Integrated I/O The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• Two serial ports

• One parallel port

• One MIDI/game port

• Six USB ports (two back-panel ports, onboard USB

headers providing maximum four extra ports: headers

USB1 & USB2)

• Audio jacks for microphone, line-in and line-out

Fast Ethernet

LAN

(for VT8235 SB

only)

• Built-in 10BaseT/100BaseTX Ethernet LAN

• VT8235 integrates Fast Ethernet MAC and VT6103 LAN

PHY in compliance with IEEE802.3u 100BASE-TX,

10BASE-T and ANSI X3.263 TP-PMD standards

• In compliance with ACPI 1.0 and the Network Device

Class Power Management 1.0

• High Performance achieved by 100Mbps clock generator

and data recovery circuit for 100Mbps receiver

USB 2.0

(for VT8235 SB

only)

• Compliant with Universal Serial Bus Specification Re-

vision 2.0

• Compliant with Intel’s Enhanced Host Controller

Interface Specification Revision 0.95

• Compliant with Universal Host Controller Interface

Specification Revision 1.1

• PCI multi-function device consists of two UHCI Host

Controller cores for full-/low-speed signaling and one

EHCI Host Controller core for high-speed signaling

• Root hub consists 4 downstream facing ports with

integrated physical layer transceivers shared by UHCI

and EHCI Host Controller

• Support PCI-Bus Power Management Interface

Specification release 1.1

• Legacy support for all downstream facing ports

BIOS

Firmware This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters and memory timing

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 305 x 244 mm. Choose a case that

accommodates this form factor.

Note: Any jumpers or connectors on your mainboard that cannot be found on

the layout are for manufacturing test only.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

• Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

• Leave components in the static-proof bags they came in.

• Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 4

Installing the Mainboard in a Case Go to page 6

Setting Jumpers Go to page 6

Installing Case Components Go to page 9

Installing the CPU Go to page 12

Installing Memory Go to page 15

Installing a HDD and CD-ROM Drive Go to page 16

Installing a FDD Go to page 18

Installing Add-on Cards Go to page 18

Connecting Options Go to page 20

Connecting Peripheral (I/O) Devices Go to page 22

Refer to the following illustration and instructions for installing the mainboard

in a case:

This illustration shows an ex-

ample of a mainboard being

installed in a tower-type case:

Note: Do not overtighten

the screws as this

can stress the main-

board.

Most system cases have

mounting brackets installed in

the case, which correspond to

the holes in the mainboard.

Place the mainboard over the

mounting brackets and secure

the mainboard onto the mount-

ing brackets with screws.

2. Secure the mainboard with

screws where appropriate.

1. Place the mainboard

over the mounting brackets.

Ensure that your case has an I/O template that supports the I/O ports and

expansion slots on your mainboard.

This section explains how to set jumpers for correct configuration of the main-

board.

Setting Jumpers

Use the mainboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the

jumper caps are placed on the correct pins.

The illustrations below show a 2-pin jumper.

When the jumper cap is placed on both pins,

the jumper is SHORT. If you remove the

jumper cap, or place the jumper cap on just

one pin, the jumper is OPEN.

This illustration shows a 3-pin

jumper. Pins 1 and 2 are SHORT.

Short Open

123

Table des matières

Autres manuels ECS Carte mère

ECS

ECS 661GX-M2 V5 Manuel utilisateur

ECS

ECS H61H2-M3 Manuel utilisateur

ECS

ECS L7VTA2 Manuel utilisateur

ECS

ECS 945GCT-M3 Manuel utilisateur

ECS

ECS Motherboard Manuel utilisateur

ECS

ECS 915P-A Manuel utilisateur

ECS

ECS 945GCT-M Manuel utilisateur

ECS

ECS 945GCD-I330 Manuel utilisateur

ECS

ECS Q77H2-TI Manuel utilisateur

ECS

ECS IC43T-A Manuel utilisateur

ECS

ECS H97I-DRONE Manuel utilisateur

ECS

ECS 945GSED-I Manuel utilisateur

ECS

ECS G41T-M7 Manuel utilisateur

ECS

ECS NFORCE6M-A Manuel utilisateur

ECS

ECS A47G Series Manuel utilisateur

ECS

ECS TIGD-CI3 Manuel utilisateur

ECS

ECS KV2 Extreme Manuel utilisateur

ECS

ECS P33T-A Manuel utilisateur

ECS

ECS Motherboard Manuel utilisateur

ECS

ECS 651C-M Manuel utilisateur

ECS

ECS A960M-M2 Manuel utilisateur

ECS

ECS G41T-M6 Manuel utilisateur

ECS

ECS A780GM-A Ultra Manuel utilisateur

ECS

ECS 865GV-M Deluxe Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur