EBN X-POS 850 Manuel utilisateur

Service Manual

X-POS 850

Copyrights

document is subject to change without prior notice in

order to improve reliability, design and function and does

not represent a commitment on the part of the

manufacturer.

This document contains proprietary information

protected by copyright. All rights are reserved. No

part of this manual may be reproduced by any

mechanical, electronic, or other means in any form

without prior written permission of the manufacturer.

All trademarks are property of their respective

owners

Liability Disclaimer

In no event will the manufacturer be liable for direct,

indirect, special, incidental, or consequential

damages arising out of the use or inability to use the

product or documentation, even if advised of the

possibility of such damages.

The information in this document is subject to

change without notice

Copyrights

Contents

Copyrights .................................................................................................i

Liability Disclaimer ...................................................................................i

Contents....................................................................................................ii

1. Before You Start ...................................................................................1

1.1. Tools Suggested .......................................................................................... 1

2. Opening the Device and HDD Removal .............................................2

2.1 How to Remove the Hinge Covers............................................................... 2

2.2 How to Install the Hinge Cover..................................................................... 2

2.2 HDD Removal ................................................................................................ 3

3. Mainboard side Components Replacement.......................................5

4.. Front-Panel side Component Replacement......................................9

1. Before You Start

1. Please unplug the power cable before you start to work.

2. Please read and follow the instructions in this document carefully. Failure to

follow these instructions could damage your device and void the warranty.

1.1. Tools Suggested

All procedures in this document require the following tools:

#0 Phillips screwdriver #1 Phillips screwdriver

(Magnetized suggested) (Magnetized suggested)

1.5 mm hexagon socket spanner

(Magnetized suggested)

Chapter 1 1

Chapter 2

2. Opening the Device and HDD Removal

2.1 How to Remove the Hinge Covers

1. Hold the upper hinge cover and push the mark.

2. Lift the upper hinge cover.

2.2 How to Install the Hinge Cover

1. Holding the lower hinge cover and pushing it softly against the rear side of the

device.

2. Align the five tenons of the upper hinge cover onto the mortises shown below

and push the mark.

3. Join the upper and lower hinge covers as directions shown below.

2.3 HDD Removal

1. Remove the screw in the blue circle and pull the HDD tray out.

2. Disconnect the SATA cable and HDD power cable.

3. Remove the HDD as shown below.

Chapter 2 3

Chapter 2

4. Un-tighten four screws and remove the base from the POS device..

5. Un-tighten two screws.

6. Open the back panel.

3. Mainboard side Components Replacement

1. Open the two ejectors on the slot by pushing them, and remove the RAM

from the slot.

2. Align and insert the new RAM into the slot and push both ends of the

RAM down until the ejectors snap into place.

3. Disconnect the SATA cable the HDD power cable from the main board.

4. Disconnect the speaker cable from the main board, and un-tighten the

four screws and then remove the speaker assembly.

Chapter 3 5

Chapter 3

5. Disconnect: 1. LCD cable, 2. inverter cable and 3. touch panel cable.

6. Disconnect: 1. Parallel port cable and 2. COM cable.

7. Disconnect: 1. Parallel port cable and 2. COM cable.

8. Loosen the four screws and disconnect the MSR cable connector.

9. Loosen the two screws by 1.5 mm hexagon socket spanner as shown

below.

10.Remove the mainboard.

Chapter 3 7

Table des matières

Autres manuels EBN Terminal tactile

EBN

EBN XPOS72-5B-A16G Manuel utilisateur

EBN

EBN X-POS956 Manuel utilisateur

EBN

EBN DNPOS70P-5BTH-N3700 Manuel utilisateur

EBN

EBN POS-7012EG-370 Manuel utilisateur

EBN

EBN EZPPC70-2B-C1G Manuel utilisateur

EBN

EBN POS50A-5B-LX800 Manuel utilisateur

EBN

EBN SPPC70-5B-C1G Manuel utilisateur

EBN

EBN POS60-8B-C1G Manuel utilisateur

EBN

EBN DNPOS70P-5BTH-N3700 Manuel utilisateur

EBN

EBN Solid POS 70 Series Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

EBN

EBN X-POS 850A Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

Prestel

Prestel VCS-G2PRO Manuel utilisateur