Eaton Powerware 9355 Manuel utilisateur

Powerware Series

Eaton 9355 Tie Cabinet

Installation Guide

For use with Eaton®9355 20/30 kVA UPSs

Class A EMC Statements

FCC Part 15

NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

ICES-003

This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment Regulations ICES‐003.

Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du Canada.

IEC 62040-2

Some configurations are classified under IEC 62040-2 as “C2 UPS for Unrestricted Sales Distribution.”

Eaton, Powerware, Powerware Hot Sync, and X-Slot are registered trademarks of Eaton or its subsidiaries and affiliates. Greenlee is a registered

trademark of Greenlee Textron. National Electrical Code and NEC are registered trademarks of National Fire Protection Association, Inc. All other

trademarks are property of their respective companies.

written approval of Eaton.

Special Symbols

The following are examples of symbols used on the UPS or accessories to alert you to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such

as important operating and maintenance instructions.

This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This product

contains sealed, lead‐acid batteries and must be disposed of properly. For more information, contact your

local recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the

trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

ON - Indicates that the switch is in the ON position.

OFF - Indicates that the switch is in the OFF position.

PHASE - The word “phase.”

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality i

Table of Contents

1 Introduction 1........................................................

2 Safety Warnings 3....................................................

3 Tie Cabinet Installation 7...............................................

4 Installing Options 19...................................................

Powerware Hot Sync CAN Bridge Card 19....................................................

5 Service and Support 27.................................................

6 Warranty 29..........................................................

Limited Factory Warranty 29..............................................................

TABLE OF CONTENTS

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality 1

Chapter 1 Introduction

A Tie Cabinet can be installed as a wall-mounted bypass or to provide support for a

parallel system for redundancy or extra capacity.

A wall-mounted bypass switch is used to bypass the UPS during maintenance or

servicing, providing wrap-around bypass for UPS service without shutting down the

load.

A parallel (load sharing) system provides more capacity than a single UPS and can

provide backup, depending on the load and configuration. In addition, when one UPS

is taken out of service for maintenance or is not operating properly, a redundant UPS

continues to supply uninterrupted power to the critical load. A parallel Powerware Hot

Sync®CAN Bridge Card provides connectivity for system metering and operational

mode control. The parallel system consists of two to four UPSs, each with a parallel

CAN Bridge Card and a parallel cabinet.

Figure 1 shows the Eaton 9355 UPS.

Figure 1. The Eaton 9355 UPS

INTRODUCTION

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality 3

Chapter 2 Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and maintenance of

the UPS and batteries. Please read all instructions before operating the equipment and save this manual for

future reference.

DANGER

This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED

SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.

WARNING

SThis UPS contains its own energy source (batteries). The UPS output may carry live voltage even when

the UPS is not connected to an AC supply.

STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity controlled,

indoor environment, free of conductive contaminants. Ambient temperature must not exceed 40°C

(104°F). Do not operate near water or excessive humidity (95% maximum).

STo reduce the risk of fire, connect only to a circuit provided with 125 amperes maximum branch circuit

overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70.

SOutput overcurrent protection and disconnect switch must be provided by others.

CAUTION

SBatteries can present a risk of electrical shock or burn from high short circuit current. Observe proper

precautions. Servicing should be performed by qualified service personnel knowledgeable of batteries

and required precautions. Keep unauthorized personnel away from batteries.

SProper disposal of batteries is required. Refer to your local codes for disposal requirements.

SNever dispose of batteries in a fire. Batteries may explode when exposed to flame.

SAFETY WARNINGS

Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality

Consignes de Sécurité

CONSIGNES DE SÉCURITÉ IMPORTANTES

CONSERVER CES INSTRUCTIONS

Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute procédure

d'installation et de maintenance des batteries et de l'onduleur. Veuillez consulter entièrement ces

instructions avant de faire fonctionner l'équipement et conserver ce manuel afin de pouvoir vous y reporter

ultérieurement.

DANGER!

Cet onduleur contient des TENSIONS MORTELLES. Toute opération d'entretien et de réparation doit être

EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ. AUCUNE PIÈCE RÉPARABLE PAR

L'UTILISATEUR ne se trouve dans l'onduleur.

AVERTISSEMENT!

SCette onduleur possède sa propre source d'alimentation (batteries). Il est possible que la sortie de

l'onduleur soit sous tension même lorsque l'onduleur n'est pas connectée à une alimentation CA.

SPour réduire les risques d'incendie et de décharge électrique, installer l'onduleur uniquement à

l'intérieur, dans un lieu dépourvu de matériaux conducteurs, où la température et l'humidité ambiantes

sont contrôlées. La température ambiante ne doit pas dépasser 40 °C. Ne pas utiliser à proximité d'eau

ou dans une atmosphère excessivement humide (95 % maximum).

SAfin de réduire les risques d'incendie, n'effectuez le raccordement qu'avec un circuit muni d'une

protection de surintensité du circuit de dérivation maximum de 125 ampères conformément au Code

Électrique National (National Electrical Code) des États-Unis ANSI/NFPA 70.

SLa protection de surintensité de sortie ainsi que le sectionneur doivent être fournis par des tiers.

ATTENTION!

SLes batteries peuvent présenter un risque de choc électrique ou de brûlure provenant d'un courant de

court-circuit haute intensité. Observez les précautions appropriées. L'entretien doit être réalisé par du

personnel qualifié connaissant bien les batteries et les précautions nécessaires. N'autorisez aucun

personnel non qualifié à manipuler les batteries.

SUne mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements en vigueur dans

votre localité.

SNe jamais jeter les batteries au feu. L'exposition aux flammes risque de les faire exploser.

Autres manuels pour Powerware 9355

Table des matières

Autres manuels Eaton UPS

Eaton

Eaton Powerware 9395 Manuel

Eaton

Eaton 9PX Instructions de montage

Eaton

Eaton 5S 550 Manuel utilisateur

Eaton

Eaton Ellipse ECO 500 Manuel utilisateur

Eaton

Eaton FERRUPS Manuel utilisateur

Eaton

Eaton Powerware 9170+ UPS 3-18 kVA Manuel utilisateur

Eaton

Eaton BladeUPS none Manuel utilisateur

Eaton

Eaton 5E Instructions de montage

Eaton

Eaton DX-EMC34 Series Manuel

Eaton

Eaton 93PM G2 Series Manuel

Eaton

Eaton Powerware 9390 Manuel utilisateur

Eaton

Eaton 9E-IN 1K Manuel utilisateur

Eaton

Eaton 9395XC Manuel utilisateur

Eaton

Eaton Powerware 9135 Manuel utilisateur

Eaton

Eaton UPS 225275 kVA Powerware 9395 Guide de dépannage

Eaton

Eaton 9E Manuel utilisateur

Eaton

Eaton Powerware 5125 Manuel utilisateur

Eaton

Eaton Powerware 9125 Manuel utilisateur

Eaton

Eaton Powerware BladeUPS Guide rapide

Eaton

Eaton Powerware 9135 Manuel utilisateur

Eaton

Eaton 5P 650i Manuel utilisateur

Eaton

Eaton 93PM IBC-L Manuel

Eaton

Eaton Ellipse ECO 500 Manuel utilisateur

Eaton

Eaton EX 2200 RT 2U Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur