Eaton Powerware 9125 Manuel utilisateur

Powerware 9125 (9910-E64) UPS

Installation Guide for IBM Applications

Special Symbols

The following are examples of symbols used on the UPS or accessories to alert you to important

information:

RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the

associated warning should be observed.

CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for

additional information, such as important operating and maintenance

instructions.

This symbol indicates that you should not discard the UPS or the UPS batteries

in the trash. This product contains sealed, lead-acid batteries and must be

disposed of properly. For more information, contact your local recycling/reuse or

hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic

equipment (WEEE) in the trash. For proper disposal, contact your local

recycling/reuse or hazardous waste center.

IBM, pSeries, AIX, xSeries, AS/400, OS/400, and RS/6000 are registered trademarks and iSeries, OpenPower, and

i5/OS are trademarks of International Business Machines Corp.

Eaton, Powerware, X-Slot, LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton Corporation

or its subsidiaries and affiliates.

Burndy is a registered trademark of Framatone Connectors International.

reproduced in any way without the express written approval of Eaton Corporation.

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 i

Table of Contents

1 Installation 1.........................................................

Parts List 1..........................................................................

Setup and Installation 4.................................................................

Tools Required 4....................................................................

Rack-Mount Setup 5.................................................................

Installing the Internal Batteries 12........................................................

Tower Setup 13.....................................................................

EBM Installation 17.....................................................................

PDM Installation 18.....................................................................

PDM Rear Panels 20....................................................................

UPS Installation 21.....................................................................

Remote Emergency Power-off Installation 22...................................................

Power Connections and Startup 23..........................................................

Typical Power Connections 28..............................................................

2 Operation 37..........................................................

Turning the UPS On 37...................................................................

Starting the UPS on Battery 37.............................................................

Turning the UPS Off 38...................................................................

Initiating the Battery Test 38...............................................................

Transferring the UPS to Bypass Mode 39......................................................

Operating Modes 39....................................................................

Normal Mode 40....................................................................

Battery Mode 41....................................................................

Bypass Mode 42.....................................................................

Standby Mode 42....................................................................

3 Communication Options 43..............................................

i5, iSeries, or AS/400 and Serial Server Interface Overview 44.......................................

Serial (TTY) Interface Overview 47...........................................................

p5 or pSeries with Logical Partitions Interface Overview 48.........................................

4 Service and Support 49.................................................

TABLE OF CONTENTS

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1

This page intentionally left blank.

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 1

Chapter 1 Installation

Parts List

IBM part numbers are subject to change without notice.

Table 1. E64 Base Configuration (42R8073)

Quantity IBM MN IBM FC IBM PN Eaton®PN Description

E64 –42R8073 103003635-3992 UPS 6000 VA, 4200W (in shipping carton or factory-installed in

rack)*

103006314 (1) Left Rail Assembly*

103006315 (1) Right Rail Assembly*

157606083-003 (2) Mounting Brackets*

180500167-203 (4) Mounting Bracket Screws (#6-32×3/8”)*

1 – – 42R8074 103003946-3992 E64 Accessory Kit

2 – – 42R4316 103003217-3991 Battery Trays

* If the UPS is factory-installed in an IBM rack, these items are pre-assembled.

Table 2. E64 Application Matrix

IBM

PN Eaton PN Description

i5/

iSeriest

Tower

IEC

i5/

iSeries

Tower

NEMA

p5/

pSeries®

Tower

IEC

p5/

pSeries

Tower

NEMA

p5/

pSeries

Rack

i5/

iSeries

Rack

–6571 42R4318 103003918-3991 NEMA

PowerPass®

Distribution

Module (PDM)

– 1 – 1 – –

–6572 42R4319 103003919-3991 IEC PDM 1 – 1 – – –

–2939* 42R4332 103004741-5591 Relay-Serial

Card and Cable

Kit (DB-9,

1.8m/6 ft; DB-25,

9.1m/30 ft)

1 1 – – – 1

* Maximum: One FC 2934 or 2939 per E64 UPS.

NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide

INSTALLATION

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1

Table 3. E64 Options Matrix

IBM

Eaton

PN Description

i5/

iSeries

Tower

IEC

i5/

iSeries

Tower

NEMA

p5/

pSeries

Tower

IEC

p5/

pSeries

Tower

NEMA

p5/

pSeries

Rack

i5/

iSeries

Rack

–2934* 39J4824 116750221-001 ConnectUPSt-X

Web/SNMP Card

– – Min: 0, Max: 1 –

–6645 42R8075 103003387-3992 Extended Battery

Module (EBM)

Min: 0, Max: 4

– – 42R8076 103003947-3992 EBM Accessory

Kit

1 per FC 6645

* Maximum: One FC 2934 or 2939 per E64 UPS.

NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide

Table 4. E64 Accessory Kit (42R8074)

Quantity Eaton PN Description

1164201513 Powerware 9125 Two-in-One UPS (5000/6000 VA) User’s Guide

1164201697 Powerware 9125 (9910-E64) Installation Guide for IBM Applications

1103004870 Software Suite CD

1157604790-002 UPS Lower Front Cover

1116750226-001 Serial Cable (RJ-45 to DB-9, 1.8m/6 ft)

1124102044-001 Serial Cable (DB-9 to DB-9, 1.8m/6 ft)

1157606088-001 Battery Retaining Bracket

2180500222-022 Battery Retaining Bracket Screws (M4×10 mm)

405147635-3 Pedestals

4180500136-202 Pedestal Mounting Screws (M4×8 mm)

1103002843-3992 Rail Hardware Kit (metric):

S(8) M5×12 Pan-Head Screws

S(8) M5×10 Flat-Head Screws

S(4) M5×16 Hex-Head Screws

S(4) M5 Clip Nuts

S(2) Square-Hole Adapter Plates

INSTALLATION

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 3

Table 5. E64 6645 EBM Components (42R8075)

Quantity IBM MN IBM FC IBM PN Eaton PN Description

1 — 6645 42R8075 103003387-3992 E64 6645 EBM 3U High (in shipping carton or

factory-installed in rack)*

103006308 Accessory Kit*:

S(1) EBM Front Cover (157604790-002)

S(1) Left Rail Assembly (103006173)

S(1) Right Rail Assembly (103006172)

1 — — 42R8076 103003947-3992 EBM Accessory Kit

* If the EBM is factory-installed in an IBM rack, these items are pre-assembled.

Table 6. EBM Accessory Kit (42R8076)

Quantity Eaton PN Description

1164201518 Powerware 240V Extended Battery Module (EBM 240) User’s Guide

1103002843-3992 Rail Hardware Kit (metric):

S(8) M5×12 Pan-Head Screws

S(8) M5×10 Flat-Head Screws

S(4) M5×16 Hex-Head Screws

S(4) M5 Clip Nuts

S(2) Square-Hole Adapter Plates

2157605902-003 Joining Brackets

4180500153-306 Joining Bracket Screws (M4×10 mm)

Table 7. FC 6571 PDM (42R4318)

Quantity Eaton PN Description

1103003918-3991 FC 6571 PDM

1103005205 Accessory Kit

S(1) Front Cover (157604790-002)

S(1) Powerware 9125 Two-in-One PDM (5000/6000 VA) User’s Guide (164201519)

S(2) Joining Bracket (157605902-003)

S(4) Joining Bracket Screws (M4×10 mm) (180500153-306)

INSTALLATION

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1

Table 8. FC 6572 PDM (42R4319)

Quantity Eaton PN Description

1103003919-3991 FC 6572 PDM

1164201519 Powerware 9125 Two-in-One PDM (5000/6000 VA) User’s Guide

1103006383 Accessory Kit

S(1) Front Cover (157604790-002)

S(2) Joining Bracket (157605902-003)

S(4) Joining Bracket Screws (M4×10 mm) (180500153-306)

2152601971-001 IEC 320-C19 to IEC 320-C20, 16A Equipment Power Cords (4.4m/14 ft)

4152601942-001 IEC 320-C13 to C14, 10A Equipment Power Cords (1.8m/6 ft)

Setup and Installation

The Powerware 9125 E64 UPS is designed for flexible configurations

and can be installed in a rack, as a standalone cabinet, or in a tower

configuration.

NOTE For UPS rack installations: If the UPS is pre-installed in an IBM rack, continue

to “Installing the Internal Batteries” on page 12. If you are installing the UPS in an IBM

iSeries (0550, 0551, 0554, or 0555 types) or pSeries (7014 type) rack, continue to the

following section, “Tools Required.” If you have another type of rack, contact your service

representative (see page 49).

NOTE For UPS standalone cabinet or tower installations: Continue to “Installing

the Internal Batteries” on page 12 to begin the UPS setup.

Tools Required

To assemble the components, the following tools may be needed:

SMedium flat-bladed screwdriver

S#2 Phillips screwdriver

S8mmwrenchorsocket

INSTALLATION

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 5

Rack-Mount Setup

The rail kit can be mounted in 48-cm (19-inch) panel racks from 61 to

76 cm (24 to 30 inches) deep.

NOTE Mounting rails are required for each individual cabinet and are located in the UPS

and EBM cartons. The UPS requires 5U and each EBM requires 3U of rack height. All

hardware is supplied.

NOTE The UPS and any optional cabinets MUST be installed at the bottom of the rack. If

placed in a rack with existing equipment, the rack must be reconfigured to allow the UPS

installation at the bottom of the rack.

Each rail kit requires one (1) of each item in the following list:

SLeft adjustable rail assembly (located in the UPS and EBM cartons)

SRight adjustable rail assembly (located in the UPS and EBM cartons)

SRail hardware kit (located in the E64 UPS and EBM accessory kits)

To install the rail kit(s):

1. Loosen the assembly wing nuts on both rail assemblies and adjust

the rail size for the depth of your rack (see Figure 1).

Rear

Front Rail Assembly

Assembly Wing Nuts

Figure 1. Adjusting the Rail Depth

2. Select the proper holes in the rail for positioning the UPS and any

optional cabinets in the rack.

Place the first rail at the bottom, using positions 1 and 6 for the

front pan-head screws. If you are installing additional rails, place the

next rail 4 holes above the last installed screw (see Figure 2).

INSTALLATION

EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1

Position 1

Position 6

Position 10

Position 15

First Rail

Second Rail

Figure 2. Front Rack Screw Positions

3. Secure the rail to the front of the rack with two pan-head screws

and one adapter plate. Insert the screws through positions 3 and 4

oftherail(seeFigure3).

NOTE Do not tighten the screws until the UPS or EBM is installed.

Autres manuels pour Powerware 9125

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Eaton UPS

Eaton

Eaton Powerware 9390-160/100 Manuel utilisateur

Eaton

Eaton Powerware 9355 Manuel utilisateur

Eaton

Eaton Ellipse PRO 650 FR Manuel utilisateur

Eaton

Eaton 9SX Series Manuel utilisateur

Eaton

Eaton 9155 N Manuel utilisateur

Eaton

Eaton TRIPP LITE Series Instructions de montage

Eaton

Eaton 9PX 1000i Manuel utilisateur

Eaton

Eaton 700VA Manuel d'utilisation

Eaton

Eaton Powerware 9395 Manuel utilisateur

Eaton

Eaton 9PXM Manuel utilisateur

Eaton

Eaton Pulsar Series Manuel utilisateur

Eaton

Eaton Powerware 9125 Manuel utilisateur

Eaton

Eaton Ellipse MAX 600 Manuel utilisateur

Eaton

Eaton 93PM-150(400) Manuel utilisateur

Eaton

Eaton Powerware 9125 Manuel utilisateur

Eaton

Eaton 9395 UPS and Plus 1 UPS 650825 kVA Manuel utilisateur

Eaton

Eaton MPS12-30 Mode d'emploi

Eaton

Eaton Powerware 9390 Manuel utilisateur

Eaton

Eaton Power Xpert 9395 550/275 Manuel utilisateur

Eaton

Eaton Power Xpert Plus 1 Manuel utilisateur

Eaton

Eaton Pulsar Series 650 Manuel utilisateur

Eaton

Eaton 91PS UPS 8-40 kW Manuel

Eaton

Eaton Tripp Lite SmartOnline Series Manuel utilisateur

Eaton

Eaton 93PM IBC-L Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur