Easyconnect FX 1600 garden Manuel utilisateur
notice-2010_66104.indd 1 10/09/2010 09:46:45
Remote Control / switches
• The remote control is not waterproof. It should always be
sheltered from rain all sources of humidity.
• Free from physical obstructions and with fully charged batteries
the effective range of the remote control is 50m.
• If their are physical obstructions and/or the batteries are weak,
the range will be reduced and/or the function altered.
• In case difculties are encountered or in case of malfunction,
change the batteries. Battery charge level affects the quality of the
radio signal and its range.
2 – TECHNICAL CHARACTERISTICS OF THE CONTROL BOX
These boxes are designed for remote (wireless)
electrical power management.
General characteristics
o Usage: Indoor and Outdoor
o Power supply: 230 V ~50 Hz
o Power consumption: 12 Watts
o Temperature range: -10°C to +50°C
o Radio frequency: 433.92 Mhz
¤ Acceptable power levels:
Recommended: 690 W
Maximum: 900 W
¤ Acceptable power levels:
Recommended: 1380 W
Maximum: 1600 W
User guide
FX 1600 garden - FX 900 garden
1 –
USER ADVICE
Control Box
• The receiver is designed for outdoor usage. It can tolerate
humidity, rain and sprayed water
• The receiver must be connected to a domestic 230V electrical
network conform to the standard NF C 15-100 and tted with a
30mA differential power breaker.
• For outdoor usage, the product must be connected to a socket
protected against water spray (IPX4).
Safety advice
• Before usage check that the box and its cabling are not
damaged. If they are damaged do not use the box, which should
be destroyed.
• The receiver box cannot be disassembled.
• Keep the product away from ames or other sources of heat.
• The product is best stored in its original packing.
Incompatible products
• Energy saving light bulbs
• Light animation or dimmer devices
• Lighting equipped with a transformer
12V, 24V, etc....
notice-2010_66104.indd 10-11 10/09/2010 09:46:46
Additional characteristics
¤ SAFETY :
The box is equipped with an automatic fuse, which cuts the circuit
when follow types of malfunction are detected:
• Cable break / short circuit
• Overheating of the system
• Power supply over voltage
• Power consumption is too high
The system restarts after removal or replacement of the faulty
item (a 10 minute delay may be necessary to allow the box to
cool down.)
¤ MEMORY :
The last function used is memorised
When the system is powered up after a long period of inactivity,
or a total power loss, the receiver will automatically start up with
the last used function.
¤ INDENTIFICATION CODE (ID):
Individual identication system
Each box has an integral identification code used for
filtering radio messages. Only the messages with the
correct identification code will be executed. This allows
the use of a multitude of different control boxes each with
individual management without creating conflicts.
¤ AUTOMATIC ACQUISITION:
Allows simple addition/replacement of transmitters
The boxes contain a system, which allows the addition or
replacement of transmitters. The system therefore allows easy
evolution and access to many applications.
3 –
SYSTEM SET UP
Control Box
• If the product does not light up, press either the ON/OFF
button or the FUNCTION button.
Remote Control
• Fit the batteries and shut the box.
• Press the ON/OFF and INTENSITY buttons (to get the basic
xed function.)
• Press on the other FUNCTIONS to vary the light effects.
• Connect the Male connecter (input) to the
power supply and the Female connector
(output) to the lights.
notice-2010_66104.indd 12-13 10/09/2010 09:46:46
4 –
FUNCTIONS
« Lighting effects »
With this box many different light effects are possible. The 28
functions of the controller allow the creation of good quality
ambiance to meet all needs...
¤ ON & OFF
¤ INTENSITY : Steady & Variation of Light intensity
With this function the light intensity can be varied from 10% to
100% to create a subdued ambience.
¤FLASH : Flashing effects
With this function slower or more rapid ashing effects can be
created for lit displays or for Christmas decoration.
¤ SAGA : Progressive effects
With this effect the lighting intensity can be varied with cycles
that are more or less rapid. This allows the progressive lighting
of trees, monuments or other objects that could benet from
such effect.
¤ OPTION : Scrolling function
This specic function is only possible with those products that
have a scrolling system. The scrolling function makes light
effects run throughout your installation. Several effects and
speed are available.
Use (+) or (–) to vary each function (7 positions pour each
function).
5 –
REPLACEMENT / AQUISITIONS
Simply add, modify or replace transmitters according to your
needs...
ON/OFF switches
1. Press and hold the “RESET” button on the
control box
2. Press and hold the “FUNCTION” button
on the control box
3.
Press twice on the power switch(es) to launch the setup sequence.
4. Release the “RESET” button
5. Release the “FUNCTION” button
Remote control
1. Press and hold the “RESET” button on the
control box
2. Press and hold the “FUNCTION” button on
the control box
3.
Press twice on the “ON/OFF” button to launch the setup sequence.
4. Release the “RESET” button
5. Release the “FUNCTION” button
Movement detector
1. Press and hold the “RESET” button on
the control box.
2. Press and hold the “FUNCTION” button on
the control box.
3. Activate signal (Red light)
¤ GREY detector – The signal is activated when the last battery
is inserted
¤ GREY/BLACK detector – The signal is activated by pressing
the button « INIT »
4. Release the button “RESET”
5. Release the button “FUNCTION”
Before any acquisition,
ensure that the box and the light are power on
Once the 5 steps are finished,
If acquistion did not ok, renew the 5 steps until obtaining the result.
notice-2010_66104.indd 14-15 10/09/2010 09:46:47
notice-2010_66104.indd 24 10/09/2010 09:46:48
Ce manuel convient aux modèles suivants
1
Table des matières
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
