East Coast Datacom PDS-1/10G Manuel utilisateur
PDS-1/10G, Portable Emulator
CHASSIS USER’S MANUAL
Revision 1.0
PDS-1/10G Portable Delay Simulato
r
Chassis User's Manual
2
SAFETY WARNING
Always observe standard safety precautions during installation, operation and maintenance of this
product. To avoid the possibility of electrical shock, be sure to disconnect the power cord from the
power source before you remove the IEC power fuses or perform any repairs.
PROPRIETARY NOTICE
The information contained herein is proprietary to East Coast Datacom, Inc. Any reproduction or
redistribution of this publication, in whole or in part, is expressly prohibited unless written
authorization is provided by East Coast Datacom, Inc.
WARRANTY NOTICE
WARRANTIES: East Coast Datacom, Inc. (hereafter referred to as E.C.D.) warrants that its
equipment is free from any defects in materials and workmanship. The warranty period shall be
three (3) years from the date of shipment. E.C.D.'s sole obligation under its warranty is limited to
the repair or replacement of defective equipment, provided it is returned to E.C.D., transportation
prepaid, within a reasonable period. This warranty will not extend to equipment subjected to
accident, misuse, alterations or repair not made by E.C.D. or authorized by E.C.D. in writing.
PUBLICATION NOTICE
This manual has been compiled and checked for accuracy. The information in this manual does
not constitute a warranty of performance. E.C.D. reserves the right to revise this publication and
make changes from time to time in the content thereof. E.C.D. assumes no liability for losses
incurred as a result of out-of-date or incorrect information contained in this manual.
Preface
3
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It provides
information for the installation and use of the chassis. Installation and maintenance should
be performed by experienced technicians only.
This document lists compatible parts available when this document was published. Refer to
the ECDATA.COM web site for updates on supported parts and configurations.
This manual may be periodically updated without notice. Please check the ECDATA.COM
website for possible updates. (http://www.ECDATA.COM).
Notes
If you have any questions, please contact our support team at:
support (at) ecdata.com
Warning! Indicates important information given to prevent equipment/property damage
or personal injury.
Warning! Indicates high voltage may be encountered when performing a procedure.
PDS-1/10G Portable Delay Simulato
r
Chassis User's Manual
4
Contents
Chapter 1 Introduction
1.1 Features ...............................................................................................................................6
Front Features.....................................................................................................................7
Rear Features .....................................................................................................................8
1.2 Optional Mounting Brackets.................................................................................................9
Installing Optional Rack Mounting Brackets......................................................................9
Mounting on a Wall ...........................................................................................................10
1.3 Unpacking the System .......................................................................................................11
1.4 Where to get Replacement Components ...........................................................................11
1.5 Returning Merchandise for Service....................................................................................11
Chapter 2 Maintenance and Component Installation
2.1 Removing Power ................................................................................................................12
2.2 Accessing the
System
........................................................................................................13
2.3 Chassis Components .........................................................................................................14
Optional Storage Drive .....................................................................................................14
Changing PCIe NIC Cards ...............................................................................................15
System Cooling .................................................................................................................16
Appendix A Power Supply Specifications
Appendix B Standardized Warning Statements for AC Systems
Contents
5
Contacting ECDATA.COM
Headquarters
Address: East Coast Datacom, Inc.
245 Gus Hipp Blvd., STE 300
Rockledge, FL 32955 U.S.A.
Tel : +1 (321) 637-9922
Fax: +1 (321) 637-9980
Email: info (at) ECDATA.COM (General Information)
support (at) ECDATA.COM (Technical Support)
Website: www.ECDATA.COM
6
PDS-1/10G Portable Delay Simulator Chassis User's Manual
Chapter 1
Introduction
The PDS-1/10G Network Emulator is a compact embedded appliance, optimized for a Mini-
ITX motherboard. The system supports 32G of RAM, XEON E-2146G and M.2 Flash Drive.
The PDS-1/10G chassis is a state-of-the-art embedded system. During the warranty
period, DO NOT attempt to take apart the system for any repairs.
1.1 Features
The following table provides you with an overview of the main features of the PDS-1/10G.
Features
Chassis
PDS-1/10G
Drives
One M.2 Flash Drive
Power
One 120W AC/DC Power Supply, 12VDC-DC ATX Power Adapter Card
Cooling
Two 4-cm chassis fans for system cooling, One Active CPU Fan
Expansion Slots
One PCIe low profile x8 slot
Motherboard Form Factor
Flex-ATX and Mini-ITX
Dimensions
(WxHxD) 10 x 1.7 x 8.9 in. (254 x 43 x 226 mm)
Front Panel
Power button, Reset button, five LED status indicators
7
Chapte
r
1: Introduction
Front Features
The front of the chassis includes the control panel.
3 4 5 6 7
2 1
Figure 1-1. Chassis Front and Control Panel
Control Panel Features
Item Features Description
1
Power button
The main power switch applies or removes primary power from the power supply
to the server but maintains standby power. To perform most maintenance tasks,
unplug the system to remove all power.
2
Reset button
Resets the system.
3
Information LED
Alerts operator to several states, as noted in the table below.
4 and 5
NIC LED
Indicates network activity on the LAN when flashing.
6
HDD LED
Indicates hard disk drive activity when flashing.
7
Power LED Indicates power is being supplied to the system power supply units. This LED is
illuminated when the system is operating normally.
8
PDS-1/10G Portable Delay Simulator Chassis User's Manual
Information LED
Status Description
Continuously on and
red
An overheat condition has occurred.
(This may be caused by cable congestion.)
Blinking red (1Hz) Fan failure, check for an inoperative fan.
Blinking red (0.25Hz) Power failure, check for a non-operational power
supply.
Solid blue Local UID has been activated. Use this function
to locate the server in a rack mount environment.
Blinking blue Remote UID is on. Use this function to identify
the server from a remote location.
Rear Features
The chassis rear Panel holds input/output ports. ***Picture varies by model purchased***
5 4
3
1 2
Figure 1-2. Rear Chassis View
Rear Chassis Features
Item Features Description
1
Power Input
The main power switch applies or removes primary power from the power supply
to the server but maintains standby power. To perform most maintenance tasks,
unplug the system to remove all power.
2
I/O ports
IPMI LAN, USB, LAN, SFP LAN, VGA
3
RJ45 window
Opening for an optional serial connector using an RJ45 jack
4
PCI window
Standard low-profile
5
K-slot for lock
Accepts a standard Kensington cable locking device (not included).
9
Chapte
r
1: Introduction
1.2 Optional 1U Rack Mounting Brackets
Installing Rack Mounting Brackets
The chassis can be mounted in a rack using two rack brackets and a two-part power adapter
shelf bracket (optional, MCP-290-10110-0B).
1. Attach the rack brackets using three screws through the holes in each bracket to secure
the bracket to the chassis.
2. Install the handles, using two screws through the bracket and into each handle.
Figure 1-5. Installing Rack Mounting Brackets
3. If you are using the optional power adapter bracket, install the power adapter on its bracket.
Place it as shown, then add the retention bracket using two screws.
4. Mount the power adapter bracket assembly on the right side of the chassis using three
screws.
10
PDS-1/10G Portable Delay Simulator Chassis User's Manual
Mounting on a Wall
Optionally, the chassis can be mounted directly on a wall, using holes in the bottom.
1. Measure and install two screws into the wall where you want to mount the server.
2. Hang the server on the screws with the Input/Output ports on the top.
Mounting Holes
Figure 1-6. Mounting on a Wall
Table des matières
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
