E-Joe EPIK SE Manuel utilisateur

EPIKSEUSERMANUAL

48V 500W EDITION

Please, read before operating your new bicycle

INTRODUCTION

Congratulations on the purchase of your new electric bicycle! We want to make you happy and believe your new bicycle will

bring you lots of fun.

We ask that you, please, read this manual thoroughly, paying special attention to the safety warnings before you start riding

your bicycle.

Please, observe traffic regulations and do not lend your bicycle to anyone who is unfamiliar with it. The bicycle can only be

legally used on the road by a person aged 14 years and older.

We strongly advise you to always wear a bicycle helmet when using your e-bike. If you are unfamiliar with cycling, we

suggest taking a cycling proficiency course prior to using your bicycle.

Before you ride your bike for the first time, please, make absolutely certain that it has been correctly assembled. You can do

this either by taking it to your nearest bicycle shop or if you are proficient in bicycle mechanics you can do the inspection

yourself. You must make certain you have the pedals, saddle, handlebar, and other items correctly fitted.

Test your brakes every time prior to using the bicycle and remember the bicycle will not stop as quickly in wet or icy

conditions as it would on a dry road.

Frequently check your tire pressure. It should be 60 psi or 4.1 bars. Low tire pressure will result in damage to the tires and

will massively reduce your speed and range.

NEVER drink alcohol and ride your electric bike. The use of alcohol greatly reduces reflexes and limits your ability to ride

safely. Even a small amount of alcohol will limit your ability to be safe on the road.

e-JOE cares for the environment and encourages its customers to properly dispose of e-JOE products in accordance with

local regulations. When you need to dispose of a lithium-ion battery, please, either dispose of the unwanted battery through

an approved recycler or send it back to us and we will make sure it is properly recycled.

Happy cycling!

YOURFRIENDSATE-JOEBIKE

OPENINGYOURBICYCLE

When receiving your bicycle, your package should contain the following items:

●The main body of the electric bike consisting of:

○Frame

○Rear wheel

○Gear and chain

○Rear brake

○Battery

○Rear fender

●The handlebar subassembly

○This subassembly is still connected to the main body by the brake/shifter cables and electrical wires. The

handlebar has the brake levers and the gear controls already assembled. Additionally, the left handle has

an LCD Power Assist Display with an integrated control for the throttle power-assisted mode.

●The seat (or saddle) attached to the pedestal stem

●The front wheel with the front brakes

●The front wheel fender with supports

●Front and rear LED lights

●Rear rack

●Pedals (2)

●Battery charger (in a separate box)

●Battery keys (2)

After unpacking, please, do not discard the box and protective material until you test the bike and make certain it is in good

working condition. Contact your dealer or e-JOE Bicycle if any of these parts are missing.

STRUCTUREOFYOURE-BIKE

Currently, electric bicycles can be divided into two classes: TAG (Twist-and-go) and PAS (Pedal Assist System). EPIK SE

belongs in the second classification. Refer to the picture below for structure and parts.

MAINSPECIFICATIONS

BIKE

Weight (with battery)

50 lbs.

Max Capacity

300 lbs.

Dimension

65” x 27” x 46”

Max Speed

20 mph

Full Charge Distance

up to 30 miles (depending on terrain and rider’s weight)

Climbing Grade

≤ 10%

Pedal Assist System

Thumb Throttle Control & 5 Level Pedal Assist

Frame

6061 Aluminum Alloy (Foldable Design)

Tires

20” x 1.75” Kenda Puncture Resistant

Seat

Selle Royal Hertz Trekking Saddle

Brakes

Front/Rear: TEKTRO 180 Rotor Disc Brakes

Gearing

7-speed Shimano Tourney TX-55

Accessories

LCD Display, Fenders, Rear Rack, Magnet Clip, Front/Rear LED Lights

MOTOR

Description

Rear Brushless Geared Hub Motor

Max Riding Noise

60 dB

Power

500 Watt Rated with 700 Watt Peak

Rated Efficiency

80%

BATTERY

Type

LG 18650-Cells Lithium Ion

Voltage

48V

Capacity

10.4A

CHARGER

Input Voltage

110-240 V

Charging Time

4-6 hrs.

How to Charge

Direct charge: Connect plug with a plug receptacle

ASSEMBLY

EPIK SE folding electric bicycle is shipped 98% assembled. In order to fully assemble the bike and prepare it for the first

use, follow these simple steps:

Step 1: Packing Material

Remove all packing and protective material and put aside. Do not discard the box or any shipping material until you test the

bike and make certain it is in good working order.

Step 2: Frame & Handlebar

Unfold the bike’s frame and lock it as shown on page 17. Stand the main body of the electric bike on the kickstand. Insert

the stem of the handlebar subassembly into the steering column that is at the front of the main body frame. Adjust the

handlebar position as instructed on page 8. Unfold the handlebar stem and lock it by following the instructions on page 16.

Step 3: Wire Harness

The earlier bike editions do not require connecting the wires after unpacking. If you have purchased the latest edition of the

bike (2018), it is necessary to connect the main wire harness with the bike components. To connect the electric wires, first,

stand in the front of the bike and locate the main wire harness with the green e-JOE logo. Connect the wires by matching

the colors AND aligning the arrows: LCD display (●gray prongs), and brake levers (●red prongs). Please, see a picture

below for reference:

Double-check the wires and make sure they are securely connected, the arrows are aligned, and the colors are not visible.

BRAKES

EPIK SE has a disk brake system installed on both the rear and the front and is used to control the entire braking system of

the bicycle.

Brake Precautions

●Do not brake too strongly or abruptly, as it will make it easier for you to fall down.

●Remember which wheel is controlled by which brake.

●Incline your body backward to reduce the influence of inertia.

●Adjust the brakes properly. Brake pads gradually wear down normal use. If the brake pads are ground flat, repair or

replace them properly.

●Check whether the braking function and braking power cut-off are working properly.

GEARS

EPIK SE comes withseven (7) gears. To change a gear, grasp the right end of the handlebar and twist up or down to your

desired gear.

●The higher the gear number, the more resistance is given when pedaling.

●If you find that when using the Pedal Assist System you are moving faster than you can comfortably pedal, try

moving to a higher gear.

PEDALS

To attach pedals, begin by identifying the right and left pedals. Look for “L” and “R”

marking on the axles, wrench flats or stickers. If no “L” and “R” markings are seen, use

pedal thread direction to identify pedals. Left threaded pedals (threads sloping upward

to the left) go to the left crank. Right threaded pedals (threads sloping upward to the

right) go to the right crank. See image if in doubt (Left: left-hand threads on the left

pedal. Right: right-hand threads on the right pedal).

Be sure to grease the pedal threads before installation. Choose the appropriate pedal and start it into the correct crank arm

by hand turning the pedal axle toward the front of the bike (both pedals thread in this direction). If it will not start, do not

force it - you are probably trying to install the left pedal on the right side or vice versa. Thread both pedals into the crank

arms as far as you can by hand. Then fully tighten them with a wrench so they do not loosen from pedal pressure. Be

careful to not overtighten the pedals as it may cause difficulties with their removal in the future.

Inflate the tires to proper pressure.

SEATANDHANDLEBARSAFEHEIGHTMARK

Vertical Handle Stem Position

Appropriate adjustments can be made for the vertical handle stem according to personal preference or riding habit, but it is

forbidden to expose the infix notation (also called, the safety line). If used inappropriately, it may cause serious injury to the

rider.

Adjustment Method:

●Unlatch locking lever at the top of the folding pipe.

●Move vertical handle stem to appropriate height making sure not to exceed the safety mark.

●Screw on the lead screw in handle core.

Seat Cushion Position

When you sit on the seat cushion, step on the pedal with your heel and lower the pedal to the lowest possible position. The

height is best suited when the leg can slightly straighten out. If only the tiptoe can step on the pedal or the leg cannot

straighten out slightly, fatigue and sports injuries may occur. Caution should be taken when making suitable height

adjustments for the seat pillar.

The MAX mark line (also called, the safety line or the infix notation), and the mark cannot be higher than tie-in of the seat

cushion. If used inappropriately, serious damage may be caused to the rider.

The angle of the saddle: In order to avoid the forward-tilt when driving, it is best to make slight upward-tilt adjustments for

the front end of the saddle. Appropriate adjustment can be made for pre- and post-position according to personal height,

and it is suitable for the seat post to be in middle position generally.

The lowest height of the seat: Move the quick release handle to “OPEN”. Put the saddle to the lowest position until it cannot

insert. Then move the quick release handle to “CLOSE”. This is the lowest height of the seat.

The highest height of the seat: Move the quick release handle to “OPEN”. Put the saddle to the highest position but not

more than the safe line. Then move the quick release handle to “CLOSE”. This is the highest height of the seat.

BATTERYANDCHARGERACCESS

Battery Access Slot

Make sure the battery is properly seated against its housing in the frame. Insert the key into the lock on the battery head.

Turn the key to remove/lock the battery in the frame.

●NOTE: The keys provided are used ONLY to lock and unlock the battery. Turning the key DOES NOT act as an

ignition for the battery or motor. Please, keep in mind that e-JOE does not carry copies of the keys. It is

recommended to store one key in a safe location in case the first key is misplaced or lost.

Battery ON/OFF Switch

Each EPIK SE battery is equipped with a red ON/OFF switch to preserve the battery when not in use. When the battery is

locked into the frame this switch is accessible through the port on the left side of the frame under the black rubber cap.

When the bicycle is not in use, turn off the red power switch on the battery.

●ON (I) = Battery is powered on. LCD Display can be turned on and the PAS, throttle, and USB port can all be used.

●OFF (O) = Battery is completely powered off. LCD Display will not turn on. PAS, throttle or any other electrical

components cannot be used. The USB will not charge any plugged in devices.

USB Port

Located next to the ON/OFF switch on the battery cap is a USB port. When the battery is locked into the frame, the USB

port is accessible through the port on the left side of the frame. When the battery is turned on, USB port can be used to

charge any device with a USB compatible charger.

●USB charging will use battery life. Be aware of battery level when charging with USB and operating bike

simultaneously.

Battery Charger and Charge Indicator Lights

To see the battery charge level, use the charge indicator on the Electric Assist LCD Display located on the left handlebar.

The battery charger for the EPIK SE is equipped with an LED light indicator that works to help you preserve the battery life

of your bicycle by allowing you to see if your EPIK SE is completely charged.

●Red = Charging

●Green = Fully Charged

Battery Precautions:

●Do not touch the poles of the battery with your hands when the battery is removed for charging. The battery poles

should not be touched with any other metal or other material that conducts electricity.

●While charging, put the battery in a secure place where children cannot reach it.

●Do not use any other charger other than the one that came with your electric bike. If you need another charger,

contact your local dealer or e-JOE Bicycle.

●Do not attempt to open or repair your charger, the electronics contain high-pressure circuits, so do not dismantle by

yourself without a professional.

●Avoid any contact with water while charging; prevent liquids, metal, and metal filings from permeating the charger,

and be careful to not drop or hit the charger which could damage its components.

●Do not put anything on top of the charger while charging; it must be well ventilated to allow the heat that is

generated to dissipate.

●Stop charging the battery immediately if you notice a peculiar smell or the charger gets too hot to touch.

●To prevent premature failure of your battery and for the warranty on your battery to remain in effect, it is

RECOMMENDED to charge and discharge your battery at least once per month. Do NOT use your battery in a very

low state.

●To preserve the life of your battery, it is RECOMMENDED that you do not leave your battery charging for periods

longer than 48 hours.

●It is normal that the distance range will reduce as a result of cells aging or battery use in low or high temperatures.

●When you need to dispose of a lithium-ion battery, either dispose of the unwanted battery through an approved

recycler or send it to e-JOE and we will make sure it is properly recycled.

●Never dispose of batteries in a fire because they may explode.

Autres manuels pour EPIK SE

Table des matières

Autres manuels e-Joe Vélo

e-Joe

e-Joe EPIK SE Manuel utilisateur

e-Joe

e-Joe Koda Manuel utilisateur

e-Joe

e-Joe ANGGUN Manuel utilisateur

e-Joe

e-Joe EPIK SWAN Manuel utilisateur

e-Joe

e-Joe Gadis Manuel utilisateur

e-Joe

e-Joe EPIK SE 2017 Manuel utilisateur

Manuels Vélo populaires d'autres marques

RAMBO

RAMBO R1000X2M-FF-BFD Manuel utilisateur

Vermeiren

Vermeiren SAFARI Manuel utilisateur

Velec

Velec A2/36V Manuel utilisateur

Coswheel

Coswheel A-ONE Manuel utilisateur

Betzold

Betzold 97869 Manuel utilisateur

Cervélo

Cervélo S3 2019 Manuel utilisateur

Tenways

Tenways AGO X Manuel utilisateur

Festo

Festo EGSC-BS-KF Manuel de la liste des pièces

Gio Electric

Gio Electric H1 Volt Manuel utilisateur

GOGOBEST

GOGOBEST GM30 Manuel utilisateur

DAHON

DAHON CIAO - 2009 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Guide de démarrage rapide

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manuel d'instructions

Greyp

Greyp G6 Series Manuel utilisateur

Babboe

Babboe Carve-E Manuel utilisateur

Huka

Huka orthros Manuel utilisateur

Xtracycle

Xtracycle Stoker 2021 Manuel utilisateur

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manuel utilisateur