Dynamite TAZER 12T Manuel utilisateur
Specications
Operation ....................................... Proportional forward,
proportional reverse with
braking delay
Input Voltage.................................. 4-cell (4.8 volts) to
6-cell (7.2 volts) DC
Peak Current .................................. 900 amperes
Continuous Current........................ 46 amperes
Full-On Resistance......................... 0.0014 ohms
Frequency ...................................... 2 kHz
BEC output..................................... 4.8 VDC, 1 amp max.
Overload Protection........................ Thermal
Dimensions.................................... 1.25" x 1.02" x .888"
(38.6mm x 26.2mm x
22.5mm)
Weight............................................ 1.2 oz (34 g)
Mounting the Speed Control
Mount the Tazer™12T ESC in the location specified by your
vehicle’s instruction manual. Use the double-sided foam tape
(included) to secure the speed control in position.
NOTE: Be sure all wiring connections can be reached
prior to mounting.
Use double-sided foam tape to secure the side of the switch to a
convenient location on the chassis or shock tower.
Wiring Diagram
Wiring the Receiver
NOTE: The Tazer 12T uses the motor battery to supply
power to the receiver through the servo wires. There is
no need for a separate receiver battery.
• See your radio’s instruction manual for proper
connection. Typically, channel 2 is used to control
the throttle.
• There are 3 wires involved in the universal receiver
connector. It is directly compatible with JR®, Hitec,
Airtronics Z, New KO and Futaba J systems.
• Older Airtronics or KO radio systems must use a
modified wiring order.
• The positive (red) and negative (brown) wires must
be reversed to operate with these radio systems. To
remove the wires from the plug, use a small jewelers
screwdriver to pry up the plastic tab associated
with each wire. Gently slide the brown wire out of the
plug. Repeat on the red wire and replace in the
opposite positions.
• Install the plug referencing the wire colors on the
steering servo for proper polarity.
Motor Capacitors
If the motor you are using (12 turns or more) does not have
3 capacitors already attached, you must install them. The
monolithic capacitors help prevent motor noise which
lessens radio glitches. Some motors have internal capacitors
that are not visible without removing the endbell. Check the
motor’s instructions to confirm if capacitors are present in
your motor. If your motor does not have capacitors, they can
be purchased at your local hobby shop. Follow the directions
below for proper connection.
1. Using a small file, scuff up an area on the motor can between
the positive and negative tabs (see figure 2).
2. Take one of the capacitors and solder one
wire to the positive motor tab with the
other wire positioned over the scuffed
area on the motor housing (see figure 3).
3. Use another capacitor and solder one
wire to the negative motor tab with the
other wire positioned over the scuffed
area as well.
4. Solder both wires to the motor housing
(see figure 4). A high wattage soldering
iron may be necessary.
5. Solder the third capacitor from the
positive to the negative motor tabs
(see figure 5).
6. Use side cuts to remove excess
capacitor wires.
Some forward-only ESCs require a shotky
diode attached to the motor for noise
suppression. Be certain there IS NOT a
diode attached to the motor when using the
Tazer 12T or any other reversing electronic
speed control.
Connecting the Motor Wires
If your motor has pre-attached male bullet connectors, press
the orange motor wire into the plug that is wired to the positive
motor terminal. The black wire is
connected in the same manner to the
negative motor tab (see figure 6).
If your motor does not have male
bullet connectors, you may purchase
them from your local hobby shop.
(“Motor Connector Wire DLR1055”).
Caution: To detour glitches caused by RF (radio
frequency) noise, route all wires and the receiver
antenna away from motor leads. Secure with tie wraps
(not included).
Connecting the Battery
The Tazer 12T comes pre-wired with a Tamiya-style connector,
compatible with most battery packs. Use battery packs from
4-cell (4.8-volt) to 6-cell (7.2-volt) sub-C size battery pack.
1. Be sure the on/off switch is in the “off” position.
2. Connect a fully charged battery pack to the speed control’s
battery connector.
Adjusting the Transmitter
NOTE: Refer to the radio instructions for specific
information on transmitter setup.
1. Set the “throttle reversing” switch to the NORMAL position.
(This may need to be reversed on some brands of radios.)
2. Set the “throttle trim” to the CENTER position.
3. Set the “throttle exponential” to MINIMUM or ZERO.
4. Set the “ATV” to 100%.
5. If your transmitter has an adjustable trigger (or stick) position,
move it to the 70/30 position.
Speed Control Programming
NOTE: While in the programming mode, no power is
applied to the motor.
1. Turn on the transmitter’s power switch. (Be sure the transmitter
batteries are fully charged).
2. Turn the ESC switch on.
3. Press and release the setup button. The red and green LEDs
will light.
4. Move the throttle to the full throttle position and press the
programming button. The green LED will remain lit and the red
LED will go out. (If the ESC does not sense throttle movement
in 3 seconds by the transmitter, it will exit the programming
mode and you will have to begin again.)
5. Now move the throttle to full reverse and press the
programming button. The red LED will glow and the green
LED will go out.
6. Return the throttle stick to neutral and press the programming
button. The green LED will glow and the red LED will go out,
indicating programming is complete.
During normal operation, the green LED indicates neutral and the
red LED indicates full forward and full reverse.
Selecting Forward Only or
Forward/Reverse Mode
The Tazer 12T has 2 modes: Forward only mode and Foward
and Reverse mode. The Forward Only mode can be selected for
racing purposes. When the ESC is powered on, the LED will flash
for 2 seconds: the color of the LED indicates which mode the
ESC is operating in:
Forward and Reverse Mode–The Green LED will Flash
Forward Only Mode–The Red LED will flash.
To change modes, push the set button and turn on the ESC. The
LED will flash, indicating the new mode has been selected. Note
the color of the LED to determine the mode of your ESC.
Instruction Manual
Thank you for choosing the Dynamite®brand. We know that
you, the customer, are the reason that we are in business.
Your satisfaction is our number one priority. With this in
mind, we have produced this product to be of the highest
quality, performance and reliability, and at a “value-packed”
price. We hope it provides you with hours of enjoyment in
your next R/C project.
Features
• High power FET control with proportional forward
and reverse.
• High frequency design delivers smooth
speed transition.
• Thermal Overload Protection prevents damage due to
over-current conditions that automatically reset.
• Pre-wired with Tamiya battery plug, bullet-style motor
connectors, and universal receiver plug that fits JR®,
Futaba J and Hitec radios.
• Designed to operate with stock motors
(12 turns or higher).
• Push-button programming makes setup a breeze.
TAZER 12T
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Orange (+)
Black (–)
CONNECT ESC
TO CH.2
POWER SWITCH
STEERING SERVO
TAMIYA 7.2V CONNECTOR
BATTERY
MOTOR
+
+
--
Troubleshooting Guide
Symptom Solution
Steering servo operates but the motor does not run Programming is not complete. Re-program the ESC by
following the programming instructions.
Speed control connected to receiver incorrectly. Refer to
manufacturer’s instructions.
Motor defective. Test motor independently, repair or
replace as needed.
Low batteries. Charge as needed.
Overload Protection enabled. Check motor
and connections.
Steering and motor do not function Receiver wired incorrectly. Check polarity and orientation
of control plugs.
Radio inoperational. See radio instruction manual.
Batteries discharged. Recharge or replace.
Full speed not attainable Transmitter adjusted improperly. See radio instructions
for proper adjustment.
ESC programmed incorrectly. Reprogram.
Motor slows but will not stop Throttle trim may be set improperly. See radio
instruction manual.
ESC program does not match transmitter.
Re-program ESC.
Reduced radio range / Interference Motor capacitors broken/missing. Repair or replace.
Motor noise. Move receiver further away from ESC, motor
and wiring.
Transmitter batteries low. Replace batteries.
Interference transmitted on or near radio frequency.
Relocate or change radio channels (see manufacturer’s
instructions).
If you as the Purchaser or user are not prepared to accept the
liability associated with the use of this Product, you are advised
to return this Product immediately in new and unused condition
to the place of purchase.
Law: These Terms are governed by Illinois law (without regard to
conflict of law principals).
Safety Precautions
This is a sophisticated hobby Product and not a toy. It must be
operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe
and responsible manner could result in injury or damage to the
Product or other property. This Product is not intended for use
by children without direct adult supervision. The Product manual
contains instructions for safety, operation and maintenance. It is
essential to read and follow all the instructions and warnings in
the manual, prior to assembly, setup or use, in order to operate
correctly and avoid damage or injury.
Questions,Assistance, and Repairs
Your local hobby store and/or place of purchase cannot provide
warranty support or repair. Once assembly, setup or use of the
Product has been started, you must contact Horizon directly. This
will enable Horizon to better answer your questions and service
you in the event that you may need any assistance. For questions
or assistance, please direct your email to productsupport@
horizonhobby.com, or call 877.504.0233 toll free to speak to a
service technician.
Inspection or Repairs
If this Product needs to be inspected or repaired, please call for
a Return Merchandise Authorization (RMA). Pack the Product
securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors
of shipping without additional protection. Ship via a carrier that
provides tracking and insurance for lost or damaged parcels, as
Horizon is not responsible for merchandise until it arrives and is
accepted at our facility. A Service Repair Request is available at
www.horizonhobby.com on the “Support” tab. If you do not have
internet access, please include a letter with your complete name,
street address, email address and phone number where you can
be reached during business days, your RMA number, a list of
the included items, method of payment for any non-warranty
expenses and a brief summary of the problem. Your original sales
receipt must also be included for warranty consideration. Be sure
your name, address, and RMA number are clearly written on the
outside of the shipping carton.
Warranty Period
Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties
that the Products purchased (the “Product”) will be free from
defects in materials and workmanship at the date of purchase by
the Purchaser
Limited Warranty
(a) This warranty is limited to the original Purchaser
(“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE PURCHASER. This warranty covers only
those Products purchased from an authorized Horizon dealer.
Third party transactions are not covered by this warranty. Proof
of purchase is required for warranty claims. Further, Horizon
reserves the right to change or modify this warranty without
notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR
REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT
THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF
THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall
be that Horizon will, at its option, (i) repair or (ii) replace, any
Product determined by Horizon to be defective. In the event of
a defect, these are the Purchaser’s exclusive remedies. Horizon
reserves the right to inspect any and all equipment involved in a
warranty claim. Repair or replacement decisions are at the sole
discretion of Horizon. This warranty does not cover cosmetic
damage or damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or modification of or to any part
of the Product. This warranty does not cover damage due to
improper installation, operation, maintenance, or attempted repair
by anyone other than Horizon. Return of any goods by Purchaser
must be approved in writing by Horizon before shipment.
Damage Limits
HORIZON SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS
OR PRODUCTION OR COMMERCIAL LOSS IN
ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE,
OR STRICT LIABILITY. Further, in no event shall the liability of
Horizon exceed the individual price of the Product on which
liability is asserted. As Horizon has no control over use, setup,
final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting
liability.
Distributed exclusively by Horizon Hobby Inc.
www.horizonhobby.com
©2007 Horizon Hobby, Inc.
Warranty Inspection and Repairs
To receive warranty service, you must include your original sales
receipt verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be repaired or
replaced free of charge. Repair or replacement decisions are at
the sole discretion of Horizon Hobby.
Non-Warranty Repairs
Should your repair not be covered by warranty the repair will
be completed and payment will be required without notification
or estimate of the expense unless the expense exceeds 50%
of the retail purchase cost. By submitting the item for repair
you are agreeing to payment of the repair without notification.
Repair estimates are available upon request. You must include
this request with your repair. Non-warranty repair estimates will
be billed a minimum of ½ hour of labor. In addition you will
be billed for return freight. Please advise us of your preferred
method of payment. Horizon accepts money orders and cashiers
checks, as well as Visa, MasterCard, American Express, and
Discover cards. If you choose to pay by credit card, please
include your credit card number and expiration date. Any
repair left unpaid or unclaimed after 90 days will be considered
abandoned and will be disposed of accordingly. Please note:
non-warranty repair is only available on electronics and model
engines.
Electronics and engines requiring inspection or repair should be
shipped to the following address:
Horizon Service Center
4105 Fieldstone Road
Champaign, Illinois 61822
All other Products requiring warranty inspection or repair should
be shipped to the following address:
Horizon Product Support
4105 Fieldstone Road
Champaign, Illinois 61822
Please call 877-504-0233 with any questions or concerns
regarding this product or warranty.
10295
Autres manuels Dynamite Système de contrôle
