DYNA Products SC-12 Manuel utilisateur
Models:
SC-12, SC-12XP, SC-14, SC-15, SC-16
FIREWOOD PROCESSORS
OPERATOR’S MANUAL
FACTORY SERVICE AND SUPPORT
888-820-3962 Toll Free
231-734-4433 Local Phone
231-734-3681 Fax
6228 60th Ave
Evart, MI 49631 USA
Visit our website for a list of US Dealers.
www.dyna-products.com
Factory Located in Evart, MI
Made in the USA
Introduction ...................................................................................4
Warranty Information.................................................................5
Safety Information.......................................................................8
DYNA SC-12/SC-12XP Firewood Processor.................... 25
DYNA SC-14 Firewood Processor....................................... 30
DYNA SC-15 Firewood Processor....................................... 37
DYNA SC-16 Firewood Processor....................................... 43
DYNA Diagram............................................................................50
Maintenance Tips........................................................................55
Parts Lists.......................................................................................57
TABLE OF CONTENTS
4
THANK YOU for purchasing your DYNA Firewood Processor.
DYNA Products continues to be a market leader in the small
to mid-size rewood processor category. Constant innovation,
attention to detail, and customer feedback are the main driving
forces behind our steady growth.
!IMPORTANT!! Please read and understand this entire
Operator’s Manual before setting up and operating your
processor. Operators must familiarize themselves with the
safety, mechanical and maintenance specications along with
operational instructions to ensure the successful, safe and long
lived use of your processor.
If you have any questions, contact us anytime!
888-820-3962 Toll Free
231-734-4433 Local Phone
Visit our website at dyna-products.com
INTRODUCTION
This manual is to provide the owner/operator with specications
and procedures for safety of operations, maintenance, and
repair of your DYNA Firewood Processor. Safety should always
be kept in mind when this machine is being operated, serviced,
stored and transported.
5
This equipment comes with a 12 month limited warranty. If any
product or part is proved to be defective within 12 months from
date of purchase, by reason, of improper workmanship and/or
material we will replace, or repair at our discretion, the part or
product at no charge to you.
To obtain warranty service, the customer must deliver the part
or product to the factory address at their expense. A copy of the
original sales invoice is required when requesting warranty work.
The warranty is limited to 60 days on the saw bar and 90 days
on the splitter wedge and the conveyor belt. The saw chain is
not covered. The KOHLER and HONDA engines are warrantied
according to their factory warranty (typically 2 years). The CAT/
KUBOTA engines are also warrantied according to their vendor.
(typically 2 years)
The above warranty does not cover defects caused by
modication, alteration, or repair of the part or product in question,
by anyone other than the manufacturer. Physical abuse to, or
misuse of the product or use or assembly thereof in any manner
contrary to the accompanying instructions and will void warranty.
DYNA FIREWOOD PROCESSOR LIMITED WARRANTY
(EXPLANATION OF APPLICATION)
During the warranty period the manufacturer of the DYNA
Firewood Processor will provide the customer replacement or
defective parts which qualify for warranty at no charge. It is
the customer’s responsibility to replace defective parts unless
special arrangements are made with selling dealer or with the
manufacturer. Labor costs for replacing chains, bearings, all
hydraulic components, or any “bolt on” components such as splitter
head, splitter back post, log decks, and engine are not reimbursed
to customer. Defective parts are to be returned to DYNA Products
at the customer’s expense.
Any unapproved repairs or modications attempted by any
individual voids all warranty and liability obligations from the
manufacturer. It is the customer’s responsibility to deliver the
WARRANTY INFORMATION
6
WARRANTY INFORMATION
machine to a Dealer or engine service center. Arrangements must
rst be made with either the manufacturer or the selling dealer. The
manufacturer does not normally reimburse the customer for any
traveling costs that occur in such cases.
All engine (CAT, KUBOTA, KOHLER, or HONDA) warranties are
handled through their manufacturer. (typically 2-3 years) These do
not come under the warranty covered by DYNA Products. Contact
info provided below.
CAT..............................................................................231 734 4433
KUBOTA Engine Power.............................................. 262 560 3214
KOHLER General Power............................................ 800 508 3246
HONDA Pace Equipment ........................................... 800 686 3128
Proper storage and adequate lubrication is important for this
machine. Engine oil and coolant levels must be checked daily.
Failure to replace wear parts or maintaining proper adjustments
can cause consequential damage. Impairments caused by neglect
on any of these issues are not covered by manufacturer’s warranty.
Fire or heat damage caused by failure to remove canvas engine
cover is not covered by manufacturer’s warranty. This refers
to damages of any kind to the cover, engine, or any part of the
machine.
Transport damages such as road wrecks or any collision of any
sort during transit are not covered by manufacturer’s warranty.
Bolts and nuts should be checked periodically. All shielding
and guarding must be properly installed and functional to keep
warranties valid.
7
WARRANTY INFORMATION
Certain wear parts are not covered under this warranty. Saw bar,
saw chain, canvas covers, and tires are not covered under any
circumstances. Splitting wedge and discharge conveyor belt
limited to the rst 90 days.
Hydraulic components must be returned with all ports plugged
or capped. Any contamination within the component will void
the warranty. All components must be complete as shipped from
factory.
Warranty is only valid when the machine has been operated under
normal circumstances and was properly maintained according to
manufacturer recommendations. Any damages caused by foreign
material or logs that are larger than rated for this model are not
covered by this warranty.
Owner agrees while requesting any warranty claims or
reimbursements that only replacement parts or repairs of existing
defective parts will be provided.
8
This manual is to provide the machine owner/operator with
specications and procedures for safe operations, maintenance,
and repair of this DYNA Firewood Processor. Safety should
always be kept in mind as this machine is being operated,
serviced, stored and transported. The noteworthy words are
described below as each issue is addressed in the following
pages.
Noteworthy Word Likelihood of
Occurrence
Degree of Injury or
Damage
!DANGER Will occur if warning is
ignored
Severe
!WARNING Can occur if warning is
ignored
Severe
!CAUTION Will or can occur if
ignored
Minor or Severe
NOTICE Important, but not
hazard related
Minor
This equipment was designed and manufactured with safety
in mind. This by itself will not prevent injury. It is the operator’s
responsibility in practicing good judgment during operation of this
machine. It is important that all safety procedures are followed as
described in this manual. The operator has the full responsibility
to follow all OSHA and ANSI guidelines.
!DANGER
Any person that is intoxicated or mentally impaired by alcohol or
any form of drugs must stay at least 100’ away from the machine.
Any unreasonable and senseless behavior is prohibited anywhere
near the general vicinity of the machine. Any person operating the
machine in such condition could result in severe injury or death.
IMPORTANT SAFETY INFORMATION
9
!WARNING
Improper use of this machine can result in severe injury or death.
Only qualied personal are allowed to operate this machine. All
potential operators must be trained and familiarized with this
manual before operating the DYNA Firewood Processor
!WARNING
It is the responsibility of the owner of this DYNA Firewood
Processor to train and qualify the operators of this machine. The
owner also assumes the authority and responsibility to insure that
all operators are practicing the “Safety of Operation” described
in this manual while operating, transporting and servicing this
machine. Performing scheduled preventive maintenance and
following manufacturer’s repair recommendations is the owner’s
responsibility and the lack thereof can cause machine harm and
personal endangerment. Any unapproved modications or repairs
without manufacturers approval will void all warranties and can
cause damage to the machine and result in severe personal
injury or death.
NOTICE
The manufacturer of the DYNA Firewood Processor reserves the
right to make modications or changes to this machine without
advanced notice. It is the owner’s responsibility to stay current
with all advancements in safety procedures that are required by
the manufacturer of the DYNA Firewood Processor. See more
information in the Warranty Section, page 5-7.
IMPORTANT SAFETY INFORMATION
10
SAFETY OF OPERATION
!DANGER
This machine was built and designed with your safety in mind.
Your physical well-being is important to us. Decals and guarding
were installed on your machine for your safety. It will only serve
as your protection if the decals are read, understood, and
followed as indicated. Guarding should be left installed and
maintained.
All operators or potential operators are to read and understand
the complete owner’s manual. It is the owner of this machine’s
responsibility to insure that all individuals operating this machine
are properly trained and qualied according manufacturer’s
recommendations. Any individual who has not read and
understood this owner’s manual and decals is NOT qualied to
operate this machine. The operator’s safety is dependent on the
individual’s knowledge of this machine and how to safely operate
this machine at full potential.
!WARNING
Almost all accidents occur when proper operator safety
procedures are not followed or machine has not been properly
maintained and/or adjusted to manufacturer recommendations.
Operator mistakes normally occur when the individual has
operated the machine for a length of time. After the operator
is accustomed to the machine the alertness and cautiousness
has a tendency to fade away. Reaching into splitter area while
splitter is in motion, steadying the log while feeding log forward or
holding onto the wood while saw is in function are some common
mistakes made when accidents happen. Usually these mistakes
are made by experienced operators. Always maintain the initial
operator alertness throughout all the time spent operating this
machine.
IMPORTANT SAFETY INFORMATION
Ce manuel convient aux modèles suivants
4
Table des matières
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
