Dyna-Glo BF10PTDG/PMDG Manuel utilisateur

VENT-FREE

BLUE FLAME

GAS WALL HEATER

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

WARNING: This appliance is equipped for

(natural or propane) gas. Field conversion is not

permitted.

- Do not store or use gasoline or other ammable vapors and Iiquids in vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency or the

gas supplier.

This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is

installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Air For Combustion and Ventilation section on page 8 of this manual.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases.

C US

ANS Z21.11.2-2013

Gas Fired Room Heaters

Volume II - Unvented Room Heaters

IMBF - 2016-04-18

MODEL #

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday or

email us at [email protected].

Propane

BF10PTDG/PMDG

BF20PTDG/PMDG

BF30PTDG/PMDG

Natural Gas

BF10NTDG/NMDG

BF20NTDG/NMDG

BF30NTDG/NMDG

WARNING: Read the Installation & Operating Instructions before using this appliance.

IMPORTANT: Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in possible injury to persons or a re

hazard and will void the warranty.

TABLE OF CONTENTS

Important Safety Information ............................................................................................................3

Product Features..............................................................................................................................6

Air For Combustion and Ventilation .................................................................................................. 8

Installation ...................................................................................................................................... 11

Operation........................................................................................................................................ 18

Care and Maintenance ...................................................................................................................22

Troubleshooting..............................................................................................................................23

Replacement Parts.........................................................................................................................27

Warranty ......................................................................................................................................... 28

PRODUCT SPECIFICATIONS

SERIES

BF10PTDG/PMDG BF20PTDG/PMDG

MAX BTU 10,000 20,000

MIN BTU 8,000 16,000

Fuel Type Propane Propane

Ignition

Electronic Push Button Electronic Push Button

Manifold Pressure 10 in. W.C. 10 in. W.C.

Inlet Gas Pressure

Maximum 14 in. W.C. 14 in. W.C.

*Minimum (*For purposes of input adjustment) 11 in. W.C. 11 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

20.00 in. x 17.32 in. x 9.49 in 24.02 in. x 20.94 in. x 10.08 in.

Fan Ratings (Select Models) 120V/60Hz,18W, 0.15A 120V/60Hz,18W, 0.15A

SERIES BF30PTDG/PMDG

MAX BTU 30,000

MIN BTU 24,000

Fuel Type Propane

Ignition Electronic Push Button

Manifold Pressure 10 in. W.C.

Inlet Gas Pressure

Maximum 14 in. W.C.

*Minimum (*For purposes of input adjustment) 11 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

24.09 in. x 28.07 in. x 10.51 in.

Fan Ratings (Select Models) 120V/60Hz,18W, 0.15A

SERIES BF30NTDG/NMDG

MAX BTU 30,000

MIN BTU 15,000

Fuel Type Natural Gas

Ignition Electronic Push Button

Manifold Pressure 5 in. W.C.

Inlet Gas Pressure

Maximum 14 in. W.C.

*Minimum (*For purposes of input adjustment) 6 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

24.09 in. x 28.07 in. x 10.51 in.

Fan Ratings (Select Models) 120V/60Hz,18W, 0.15A

SERIES BF10NTDG/NMDG BF20NTDG/NMDG

MAX BTU 10,000 20,000

MIN BTU 5,000 10,000

Fuel Type Natural Gas Natural Gas

Ignition Electronic Push Button Electronic Push Button

Manifold Pressure 5 in. W.C. 5 in. W.C.

Inlet Gas Pressure

Maximum 14 in. W.C. 14 in. W.C.

*Minimum (*For purposes of input adjustment) 6 in. W.C. 6 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

20.00 in. x 17.32 in. x 9.49 in. 24.02 in. x 20.94 in. x 10.08 in.

Fan Ratings (Select Models) 120V/60Hz,18W, 0.15A 120V/60Hz,18W, 0.15A

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate,

or service this heater. Improper use of this heater can cause serious injury or death from burns, re,

explosion, electrical shock, and carbon monoxide poisoning.

IMPORTANT SAFETY INFORMATION

Installation and repair should be done by a qualied service person. The appliance should be

inspected before use and at least annually by a professional service person. More frequent

cleaning may be required due to excessive lint from carpeting, bedding material, etc. It

is imperative that control compartments, burners and circulating air passageways of the

appliance be kept clean.

WARNING: Any change to this heater or its controls can be dangerous.

WARNING: Carefully supervise young children when they are in the room with the heater.

WARNING: Heater becomes very hot when operating. Children and adults should be alerted

to the hazard of high surface temperatures and should stay away to avoid burns or clothing

ignition Heater will remain hot for a time after shutoff. Allow surfaces to cool before touching.

WARNING: Make sure any panel, safety screen or guard removed for servicing an appliance

is replaced prior to operating the heater

WARNING: Keep the appliance area clear and free from combustible materials, gasoline, and

other ammable vapors and liquids.

WARNING: Do not place clothing or other ammable material on or near the appliance. Never

place any objects on the heater.

WARNING: Due to high temperatures, locate this appliance out of trafc and away from

furniture and draperies.

This appliance is intended for supplemental heating.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the u with

headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get

fresh air immediately! Have heater serviced. Some people are more affected by carbon monoxide than

others. These include pregnant women, people with heart or lung disease, people who are

anemic, those under the inuence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS: Natural and Propane/LP gases are odorless. An odor-making

agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas

can fade. Gas may be present even though no odor exists. Make certain you read and understand all

warnings. Keep this manual for reference. It is your guide to operating this heater safely.

If the heater is being installed in a residential garage, it must be secured rmly to the

wall, a minimum of 18 in. (457mm) above the oor. The heater must be located so that it

is protected against any possibility of damage by a moving vehicle, etc.

Raising the heater will reduce BUT NOT eliminate the possibility of lighting the vapor of any

ammable liquids which may be improperly stored or accidentally spilled. If the smell of

gasoline is present, do not operate this heater until the area has been properly ventilated.

WARNING:

CALIFORNIA PROPOSITION 65

Fuels used in gas or oil red appliances and the products of combustion of such fuels contain

chemicals known to the state of California to cause cancer, birth defects or other reproductive

harm. This product contains chemicals, including lead and lead compounds, known to the state of

California to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

WARNING: Do not use any accessories not approved for use with this heater.

SAFETY INFORMATION

1. Do not place Propane/LP supply tank(s) inside any structure. Place Propane/LP supply tank(s)

outdoors.

2. Only the BF10 series can be installed in a bedroom. When installing in a bedroom

the heater MUST be mounted to the wall (See Wall Mounting, Page 14). All other models cannot

be installed in a bedroom. These units are not approved for bathroom use.

3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing

(ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available.

See Air for Combustion and Ventilation, pages 7 through 9. If heater keeps shutting off, see

Troubleshooting, pages 22 through 25.

4. Keep all air openings in front, top and bottom of heater free of objects and debris to ensure

adequate air for proper combustion.

5. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting

off, have it serviced.

6. Do not run heater:

• Where ammable liquids or vapors are used or stored.

• Under dusty conditions.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater and pilot off. If

heated, the vapors from these products may create a white powder residue within burner box or

on adjacent walls or furniture.

8. Do not use heater if any part has been under water. Immediately call a qualied service technician

to inspect the room heater and to replace any part of the control system and any gas control

which has been under water.

9. Turn off and unplug heater and let cool before servicing. Only a qualied service person should

service and repair heater.

10. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

11. WARNING: Do not allow fans to blow directly into the heater. Avoid any drafts that alter

burner ame patterns.

12. WARNING: Do not operate heater if the tempered glass panel is not secured, broken, or

missing. Only replace the tempered glass panel with parts and/or components provided by

GHP Group, Inc.

13. SAVE THESE INSTRUCTIONS.

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air and cuts off main burner gas in the

event of ame out.

LEG KIT (SELECT MODELS)

2 support legs and 4 support leg screws are included for oor mounting the heater. See page 13.

NOTE: This is an optional accessory and is not required for operation of the heater.

ELECTRONIC PUSH BUTTON IGNITION SYSTEM

This heater is equipped with an electronic push button ignition system. This system requires

one AAA battery (provided).

THERMOSTAT HEAT CONTROL (SELECT MODELS)

The control automatically cycles the burner on and off to maintain a desired room

temperature. See page 24.

FAN KIT (SELECT MODELS)

The fan kit helps to distribute the warmed air into the space more rapidly.

NOTE: This is an optional accessory and is not required for operation of the heater.

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in

the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-red

supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale

of the unit.

In the State of Massachusetts, unvented propane or natural gas-red space heaters shall

be prohibited in bedrooms and bathrooms.

In the State of Massachusetts the gas cock must be a T-handle type. The State of

Massachusetts requires that a exible appliance connector cannot exceed three feet

in length.

LOCAL CODES

Install and use heater with care. The installation must conform with local codes or, in the absence of

local codes, with the latest edition of The Nation Fuel Gas Code, ANSI Z223.1/NFPA 54

*Available from:

American National Standard Institute, Inc. National Fire Protection Association, Inc.

1430 Broadway 1 Batterymarch Park

New York, NY 10018 Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit, restrict

and or have special requirements for vent-free heaters.

PREPARING FOR INSTALLATION

Before beginning assembly or operation of the product, make sure all parts are present.

Compare parts with package contents list. If any part is missing or damaged, do not attempt

to assemble, install or operate the product. Contact customer service for replacement parts.

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to heater for shipping

3. Verify all contents are present.

NOTE: Support Leg Screw (M4*15) (Select Models), Wood Screw (ST4.8*45-16),

Expansion Bracket Screw(ST4.8*15-16), and Expansion Bracket come with (2) extra each.

4. Check heater for any shipping damage. If heater is damaged, promptly inform dealer where you

bought the heater.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces

approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (.3 Kw) of gas input

per hour. An unvented room heater is intended as a supplemental heater rather than a primary heat

source. In most supplemental heat applications, the water vapor does not create a problem.

In most applications, the water vapor enhances the low humidity atmosphere experienced during

cold weather.

The following steps will help ensure that water vapor does not become a problem:

1. Be sure the heater is the proper size for the application, including adequate combustion air and

circulation air.

2. If there is high humidity, a dehumidier may be used to help lower the water vapor content

of the air.

3. Do not use an unvented room heater as the primary heat source.

Expansion

Bracket x 4

Expansion Bracket

Screw (ST4.8*15-16) x 4

Wall Hanging

Spacer x 2

Wood Screw

(ST4.8*45-16) x 4

Expansion Bracket

Tool x 1

Wall Hanging

Spacer Screw

(M4*25) x 2

Wall Mounting

Bracket x 1

Support Leg Screw

(M4*15) x 4

(Select Models)

Support Leg x 2

(Select Models)

AAA Battery x 1

PREPARING FOR INSTALLATION

AIR FOR COMBUSTION AND VENTILATION

CAUTION: This heater shall not be installed in a room or space unless the required volume of

indoor combustion air is provided by the method described in the National Fuel Gas Code, ANSI

Z223.1/NFPA54, the International Fuel Gas Code, or applicable local codes.

PRODUCING ADEQUATE VENTILATION

All spaces in homes fall into one of the three following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 8 through 10 will help you classify your space and provide adequate ventilation.

Conned and Unconned Space

A conned space as a space whose volume is less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw)

of the aggregate input rating of all appliances installed in that space and an unconning space as a

space whose volume is not less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate

input rating of all appliances installed in that space. Rooms connecting directly with the space in

which the appliances are installed*, through openings not furnished with doors, are considered a

part of the unconned space.

This heater shall not be installed in a conned space or unusually tight construction unless provisions

are provided for adequate combustion and ventilation air.

* Adjoining rooms are connecting only if there are doorless passageways or ventilation

grills between them.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and venti-

lation. However, in buildings of unusually tight construction, you must provide additional

fresh air.

Unusually tight construction is dened as construction where:

a) walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder

with a rating of one perm (6x10-11kg per pa-sec-m2) or less with openings gasketed or sealed

and

b) weather stripping has been added on windows that can be opened and on doors and

c) caulking or sealants are applied to areas such as joints around window and door frames,

between sole plates and oors, between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air.

See “Ventilation Air From Outdoors” (page 10). If your home does not meet all of the

three criteria above, proceed to “Determining Fresh-Air Flow For Heater Location”.

PREPARING FOR INSTALLATION

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Conned or Unconned Space

Use this worksheet to determine if you have a conned or unconned space.

Space: Includes the room in which you will install heater plus any adjoining rooms with

doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space Length × Width × Height = cu. ft. (volume of space)

Example: Space size 20 ft. (length) × 16 ft.(width) × 8 ft. (ceiling height) = 2560 cu. ft. (volume

of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these

rooms to the total volume of the space.

2. Divide the space volume by 50 cu. ft. to determine the maximum BTU/hr the space can support.

_______ (volume of space) ÷ 50 cu. ft.= (Maximum BTU/hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum BTU/hr the space

can support)

3. Add the BTU/hr of all fuel burning appliances in the space.

Vent-free heater _________ BTU/hr

Gas water heater* ________BTU/hr

Gas furnace _____________BTU/hr

Vented gas heater ________BTU/hr Example:

Gas heater logs __________BTU/hr Gas water heater 30,000 BTU/hr

Other gas appliances*+ ____BTU/hr Vent-free heater + 26,000 BTU/hr

Total = ____BTU/hr Total = 56,000 BTU/hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.

_______ BTU/hr (maximum the space can support)

_______ BTU/hr (actual amount of BTU/hr used).

Example : 51,200 BTU/hr (maximum the space can support) 56,000 BTU/hr (actual amount of

BTU/hr used)

The space in the above example is a conned space because the actual BTU/hr used is more than

the maximum BTU/hr the space can support.

You must provide additional fresh air. Your options are as follows:

a) Rework worksheet, adding the space of an adjoining room. If the extra space provides an

unconned space, remove door to adjoining room or add ventilation grills between rooms. See

“Ventilation Air From Inside Building,” page 10.

b) Vent room directly to the outdoors. See “Ventilation Air From Outdoors”, page 10.

c) Install a lower BTU/hr heater if lower BTU/hr size makes room unconned. If the actual BTU/hr

used is less than the maximum BTU/hr the space can support, the space is an unconned space.

You will need no additional fresh air ventilation.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Dyna-Glo Chauffage

Dyna-Glo

Dyna-Glo RA125DGD Manuel de service

Dyna-Glo

Dyna-Glo RMC-KFA45T, RMC-KFA65T, RMC-KF Manuel utilisateur

Dyna-Glo

Dyna-Glo KFA80H Manuel

Dyna-Glo

Dyna-Glo BFSS20LPT-2P Manuel utilisateur

Dyna-Glo

Dyna-Glo KFA50H Manuel

Dyna-Glo

Dyna-Glo RMC-KFA70TDGP Manuel utilisateur

Dyna-Glo

Dyna-Glo IR6PTDG-1/PMDG-1 Manuel utilisateur

Dyna-Glo

Dyna-Glo HeatAround360 Manuel

Dyna-Glo

Dyna-Glo WORKHORSE FA43 Series Manuel

Dyna-Glo

Dyna-Glo KFA80C Manuel utilisateur

Dyna-Glo

Dyna-Glo WORKHORSE Series Manuel

Dyna-Glo

Dyna-Glo SF70DGD Manuel

Dyna-Glo

Dyna-Glo RMC-KFA50DGP Manuel

Dyna-Glo

Dyna-Glo PROFESSIONAL OHIR18LV Instructions de montage

Dyna-Glo

Dyna-Glo SF70DGD Manuel utilisateur

Dyna-Glo

Dyna-Glo KFA50WH Manuel

Dyna-Glo

Dyna-Glo DELUX KFA50DGDR Manuel utilisateur

Dyna-Glo

Dyna-Glo WK95C6C Manuel utilisateur

Dyna-Glo

Dyna-Glo RMC- 95C6 Manuel utilisateur

Dyna-Glo

Dyna-Glo DELUX LPFA43DGD Manuel

Dyna-Glo

Dyna-Glo EG4800DGP Instructions d'installation et d'utilisation

Dyna-Glo

Dyna-Glo EG5000DGC Instructions d'installation et d'utilisation

Dyna-Glo

Dyna-Glo RMC-LPC25DG Manuel du propriétaire

Dyna-Glo

Dyna-Glo RA18LPDG Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur