Dymo 1570 Manuel utilisateur

DYMO 1570

Adjusting Space on Label Ends

For more blank spaces before and after messages: Turn the tape feeder (B) .

For less blank spaces: Turn the tape feeder (B) in reverse, emboss the message, turn feeder

forward, and cut.

To center a message: Advance completed label 3 spaces (5 space for 1530 Office Mate I)

Squeeze tape cutter.

Troubleshooting

Label shows letters instead of blank space: Squeeze handle half way until you hear a click,

then release.

Letters too light: Squeeze harder by holding the upper end of the handle.

Tape jam: In the unlikely event the tape does not feed properly, remove the tape wheel, discard

left over tape ends, and replace the wheel.

Preparing Problem Surfaces

Use non-residual solvents (i.e., alcohol, acetone) to clean oily or greasy surfaces. If the surface is

rough or porous, coat it with a sealer (i.e. shellac, lacquer). Once stuck, water will not affect the

label. Do not apply labels to surfaces exceeding 140 F.

1. Load Tape

Expose 3" of the tape, open the tape compartment (A), and insert so that ‘U’ shape opening in the

tape cartridge points down. Insert the tape into the feed slot and thread forward until visible.

Close the tape compartment to lock in the tape.

2. Advance Tape

By turning the feeder (B) or with several half-squeezes (squeeze until click sound is audible) of

the handle (F), advance the tape 1/4" past front of embosser.

3. Emboss Letters

Turn the wheel (E) until the desired letter aligns with selector. Squeeze the handle (F) firmly and

repeat for each letter. To space between words, half-squeeze handle until click is heard.

DO NOT HOLD WHEEL WHILE EMBOSSING.

4. Cut Tape

Squeeze the cutter (C) and remove excess tape from the end of the embosser.

5. Apply Label

Pull the end of the tab to strip the backing. Apply tape to a clean dry surface.

6. Change Wheel

Push wheel right to left and remove. Snap in the new wheel.

DO NOT SQUEEZE HANDLE WHILE CHANGING WHEEL.

Table des matières

Autres manuels Dymo Étiqueteuse

Dymo

Dymo LabelManager 260P Manuel utilisateur

Dymo

Dymo Cool Clicks Manuel utilisateur

Dymo

Dymo MobileLabeler Manuel utilisateur

Dymo

Dymo LP300 Manuel utilisateur

Dymo

Dymo LabelManager 220P Manuel utilisateur

Dymo

Dymo Rhino 5200 Hard case Kit by Manuel utilisateur

Dymo

Dymo RhinoPRO 5000 Manuel utilisateur

Dymo

Dymo LW 450 Manuel utilisateur

Dymo

Dymo ExecuLabel LM450 Manuel utilisateur

Dymo

Dymo LP300 Manuel utilisateur

Dymo

Dymo Rhino 6500 Manuel utilisateur

Dymo

Dymo 1575 Manuel utilisateur

Dymo

Dymo LabelWriter SE300 Manuel utilisateur

Dymo

Dymo LabelMANAGER 150 Guide de démarrage rapide

Dymo

Dymo LabelMANAGER 150 Manuel utilisateur

Dymo

Dymo Rhin 4200 Manuel utilisateur

Dymo

Dymo LabelManager 500TS Manuel utilisateur

Dymo

Dymo Rhino 3000 Industrial Label Printer Manuel utilisateur

Dymo

Dymo RhinoPRO 1000 Manuel utilisateur

Dymo

Dymo LetraTag XR Manuel utilisateur

Dymo

Dymo 2000 Manuel utilisateur

Dymo

Dymo LabelManager 500TS Manuel utilisateur

Dymo

Dymo LetraTag Manuel utilisateur

Dymo

Dymo LabelPOINT 100 Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur