Dwin 2 Manuel utilisateur

Operating Instructions

Read these instructions completely before operating this unit.

Contents subject to change without notice or obligation.

Printed in USA TranScanner 2

Rev. 9

- 2 of 18 -

Table of Contents

Safety Instructions .......................................

Specifications ............................................

Introduction ..............................................

Programming SL-8000 Remote Control to Operate TranScanner 2 5

Installation ............................................ 6

Quick Reference Remote Control Operation .................. 8

The Front Panel Controls.................................. 9

Using The Control Menus ................................... 9

Main Menu ............................................ 9

Video Control Menu.................................... 9

Input Menu ........................................... 10

Aspect Ratio Menu .................................... 10

Setup Menu ........................................... 10

Auto Input Select ................................. 11

Menu Timeout....................................... 11

Rename Inputs...................................... 11

Rename Aspect Ratios............................... 11

Display Setup...................................... 12

IR Setup........................................... 13

Relay Setup........................................ 14

OSG Setup.......................................... 14

TranScanner 2 Aspect Ratio Guide........................... 15

TranScanner 2 RS-232 Control............................... 17

Warranty .................................................. 18

- 3 of 18 -

Safety Instructions

WARNING

HAZARDOUS VOLTAGE

DO NOT OPEN

ATTENTION

COURANT ELECTRIQUE

NE PAS OUYRIR

CAN SHOCK, BURN OR CAUSE SEVERE INJURY OR DEATH. DO NOT

REMOVE THE TOP COVER. REFER SERVICING TO QUALIFIED PERSONNEL.

1. Read and apply all of the safety and operating instructions provided with your video equipment.

2. Keep all safety and operating instruction for future reference.

3. Unplug this video equipment from the wall outlet before cleaning. Never use liquid or aerosol cleaners.

Use only a damp cloth for cleaning.

4. Do not use any attachments or accessories not recommended by the manufacturer as they may cause

hazards.

5. Do not use this video equipment near water. Avoid placing it near a bathtub, kitchen sink, or laundry tub,

in a wet basement, or near a swimming pool.

6. Do not place this video equipment on an unstable cart, stand, or table. The video equipment may fall,

causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or

stand recommended by the manufacturer. Wall or shelf mounting should follow the manufacturer's

instructions, and should use a mounting kit approved by the manufacturer.

6A. Move any appliance and cart combination with care. Quick stops, excessive force, and uneven surfaces

may cause the appliance and a cart to overturn.

7. Side openings in the cabinet are provided for ventilation, and to insure reliable operation of the video

equipment and protect it from overheating. These openings must not be blocked or covered. Never place

the video equipment on a bed, sofa, rug, or other similar surface that may block ventilation openings.

Never place this product near or over a radiator or heat register. Do not place this product in a built-in

installation such as a bookcase or rack unless proper ventilation is provided.

8. Operate only from the type of power source indicated on the marking label. If you are not sure of the type

of power supply to your home, consult your appliance dealer or local power company.

9. This unit is equipped with a three conductor polarized alternating-current line plug. This plug will fit into the

power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet,

contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized

plug.

10. Route power-supply cords so that they will not be walked on or pinched by items placed on or against

them. Pay particular attention to cords at plugs, convenience receptacles, and the points where they exit

the products.

11. Protect your video equipment from lightning during a storm or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet. This will prevent damage to the unit due to lightning

and power-line surges.

12. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

13. Never push objects of any kind into this video equipment through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of

any kind on the video equipment.

14. Do not attempt to service this unit yourself as opening or removing cover may expose you to dangerous

voltages or other hazards. Refer all servicing to qualified service personnel.

15. Unplug this video equipment from the wall outlet, and refer servicing to qualified service personnel under

the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the video equipment.

c. If the video equipment has been exposed to rain or water.

d. If the video equipment does not operate normally by following the operating instructions.

- 4 of 18 -

Adjust only those controls that are covered by the operating instructions as improper

adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the video equipment to normal operation.

e If the video equipment has been dropped or the cabinet has been damaged.

f. When the video equipment exhibits a distinct change in performance.

16. When replacement parts are required, be sure the service technician has used replacement parts

specified by the manufacturer that have the same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other hazards.

17. Upon completion of any service or repairs to this video equipment, ask the service technician to perform

routine safety checks to determine that the system is in safe operating condition.

18. Do not place anything on the video equipment. heavy objects placed on any part of this system will cause

damage.

19. WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

20. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE EXPOSURE.

NOTE 1: This equipment is designed to operate in the USA, Canada and other countries where the

broadcasting system and AC house current is exactly the same as in the USA and Canada.

IMPORTANT INFORMATION FOR THE USER

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communication. However, there is no guarantee that harmful interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or and experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition:

( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept interference received,

including interference that may cause undesired operation.

Note: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may

void the user’s authority to operate the equipment.

- 5 of 18 -

S P E C I F I C A T I O N S

V i d e o In p u t Te r m i n a l s (S e v e n In p u ts )

Composite Video 1 Vp-p 75 Ohm

Component Video

Y: 1 Vp-p 75 Ohm

R-Y: 0.7 Vp-p 75 Ohm

B-Y: 0.7 Vp-p 75 Ohm

S-Video Y: 1 Vp-p 75 Ohm

C: 0.28Vp-p 75 Ohm

RGBS Input 0.7 Vp-p 75 Ohm

H & V Sync Input TTL Levels

RS232 Serial Computer Control

O u tp u t Te r m i n a l s

RGBS Outputs: 0.7 Vp-p 75 Ohm

Negative V & H/C SYNC Output:

1.5 Vp-p 75 Ohm

Horizontal Frequency: 31.5 - 64 kHz

Vertical Frequency: 50 or 60 Hz

P o w e r Re q u i r e m e n ts :

Model TranScanner 2-1 117 VAC 60Hz

Operating range (105 to 130) VAC

Model TranScanner 2-2 220 VAC 50Hz

Operating range (205 to 240) VAC

P o w e r Co n s u m p ti o n : 25 Watt Max

D i m e n s i o n s : (WxHxD)17"x3.5"x13"

A c c e s s o r i e s In c l u d e d :

•Wireless Remote Control

•6' AC Line Cord

•Operator's Manual

•2.5mm DC Jack

O p ti o n a l Ac c e s s o r i e s :

•19" Rack-mount Kit

Introduction

The TranScanner 2 is a variable line multiplier designed for use with projectors that have a scanning frequency

between 31.5kHz to 64kHz.

The TranScanner 2 cannot be used with a conventional television receiver or projector.

The projector or monitor used with the TranScanner 2 must have an RGB+S input and a horizontal scanning

frequency of between 31.5 kHz - 64 kHz.

Operating at this higher frequency, the TranScanner 2 multiplies the number of scanning lines, interpolating the

additional picture information from detail found in the original source material.

The scanning lines visible on conventional large screen displays are virtually eliminated and the new picture is

bright, colorful, and "film like".

The TranScanner 2 provides source switching for nine different inputs including three component ( Y, Cr, Cb ),

two composite video inputs, two S-VIDEO (Y/C) inputs and two RGB H & V Sync inputs.

An infrared wireless remote control with on-screen graphics selects the input source and adjusts all of the

operating controls.

Video controls include: contrast, brightness, color, tint, and sharpness.

Settings for each individual video input may be adjusted and stored separately in the controller's nonvolatile

memory. These settings will be restored each time that input is selected.

Programming SL-8000 Remote Control to Operate the TranScanner 2

The TranScanner 2 is shipped with a factory pre-programmed remote control.

1. Press the “AUX” and the “MUTE” buttons simultaneously. "SET" will appear on the LCD.

2. Enter the TranScanner 2’s brand code: “080”.

3. Press “AUX” button to complete the programming.

To operate other audio and video devices refer to the “SL-8000 Operating Manual”.

- 6 of 18 -

Installation

115 VAC 60 Hz

65 WATTS MAX.

222

RED GREEN BLUE

+12 VDC

100 mA

TranScanner 2 Rear Panel

123

VIDEO INPUTS

RGBS 2

INPUT

Cr1

Cr2

Cb1

Cb2

RS232

CONTROL """"""""

S1 S2

RY1 RY2 22

H SYNC V SYNC C SYNC

OUTPUTS 11

Cr3

Cb3

RGBS 1

INPUT """"

"""""

1. Switched +12VDC Outputs, RY1, RY2 2.5mm DC Plug

2. Red, Green, Blue H, V and C Sync Outputs BNC

3. RGBS Computer Inputs 15 pin HD Socket

4. RS-232 Computer Input 9 pin D Plug

5. S-Video Inputs ( S1, S2 ) 4 pin Mini-Din

6. Composite Video Inputs ( V1, V2 ) RCA Type

7. Component Video Inputs (Y1, Cr1, Cb1) RCA Type

(Y2, Cr2, Cb2)

(Y3, Cr3, Cb3)

1. SWITCHED +12VDC OUTPUTS

The TranScanner 2 has two switched +12 VDC outlets labeled as RY1 and RY2. These outlets may be used to

trigger a relay in an electric screen, projector lift or some other relay activated device. See “Relay Setup” menu

for more details.

2. RED, GREEN, BLUE AND H, V, C SYNC OUTPUTS

The output video signal from the TranScanner 2 to the display device is made via five BNC connectors for Red,

Green, Blue, H and V Sync. High quality 75 Ohm coaxial cables are recommended to connect the output of

TranScanner 2 to the display device.

The composite C Sync output may be used for displays that accept composite sync input.

3. RGBS INPUTS

The RGBS1 and RGBS2 inputs are provided for sources such as personal computers, HD tuners, video

cameras, graphic generators, and other video equipment with an RGB and Sync output.

Since these sources already operate at a horizontal frequency that is higher than conventional NTSC or PAL

video, the TranScanner 2 does not multiply their scan rate. However, the TranScanner 2 provides source

switching for these inputs, converts H & V Sync to composite Sync, provides control of contrast and brightness,

and amplifies RGB video signals to allow the use of longer cable lengths.

The TranScanner 2 will automatically switch to a RGB input if proper Horizontal or Composite Sync is applied at

pin 13 of the D-15 RGB connector.

The pin assignments for the 15 PIN "D" connector are as follows:

1. Red

2. Green

- 7 of 18 -

3. Blue

13. Horizontal Sync

14. Vertical Sync

6-9. Ground

The RGB source must be an analog signal with a horizontal frequency which is compatible with the scanning

frequencies of the projector or monitor.

4. RS-232 COMPUTER INPUT

The RS-232C serial interface is provided for external control of the TranScanner 2 from a central controller, such

as a Home Theater control computer, Smart Home automation system, etc.

For DB9 connector pin-out and RS232 command list please refer to “TranScanner 2 RS232 Control” section.

5. S-VIDEO INPUTS (S1, S2)

The S1 and S2 inputs are provided for video recorders, DVD players, DSS receivers, video cameras and laser

disc players which have an S-VIDEO (Y/C) output. The tape quality from machines with S-VIDEO outputs is

maximized if the tapes were recorded in the S-VIDEO format.

6. COMPOSITE VIDEO INPUTS (V1, V2)

The V1 and V2 inputs are provided for laser disc players, non S-VIDEO tape machines, satellite receivers, video

tuners, video cameras and other equipment which has a composite video output.

7. COMPONENT VIDEO INPUTS (Y-Cr-Cb)

Three component video inputs are provided for DVD players and HD sources.

For an interlaced component video signals such as from a regular DVD player (480i component signal), the

TranScanner 2 provides deinterlacing, scaling and complete picture controls, including a full range of color

saturation and hue controls.

For component video signals from a progressive DVD (480p component signal), or from an HD tuner (1080i or

720p component signal), the TranScanner 2 provides signal transcoding from component to RGB and full range

of picture contrast and brightness controls. Each of these component inputs may be connected to any of 480i,

480p, 1080i or 720p above mentioned component sources. The TranScanner 2 determines which type of

component video signal is applied to its input and processes it accordingly.

- 8 of 18 -

Quick Reference Remote Control Operation

CENTER SUR

GUIDE MENU

POWER

AUD CD TAPE AUX

SAT TV VCR CBL

VOL CH

MUTE T/V

PAUSE

STOP

EXIT PRE.

DELAY -- DELAY +

1 2 3

4 5 6

7 8 9

FAV

SLEEP

INFO

PRO.L

3.CH

ALT

TEST

+10 0 ENTER

----------pip------- SHIFT

TUNER CD TAPE1 TAPE2 PHONO

VCR1 VCR2/SAT LDP AUX TV

M1 M2 M3 M4

LIGHT

HOME THEATER MASTER

SL-8000

SEL

PLAY

]

The remote control furnished with the

TranScanner 2 is a universal remote control

capable of controlling 8 different devices. To

control the TranScanner 2 select “AUX” mode.

1. Press “POWER” button to turn the TranScanner

2 ON or OFF. For discrete ON and OFF IR

commands please refer to “IR Setup” menu.

2. Press “MENU” to display the Main menu, or to

toggle between submenus and the main menu.

3. NUMBERED Buttons – are used for direct

access to inputs.

To select a specific input, press a numbered

button.

Video inputs are “1” and “2”;

S-Video inputs are “3” and “4”;

Component (Y,Cr Cb) inputs are “5”, “6”and “7”;

RGB inputs are “8”and “9”.

4. Press up

or down

]

buttons to sequences

through the on screen menu options.

5. Press left

or right

buttons to adjust and/or

select the on-screen menu options.

6. Press “EXIT” button to clear the on-screen

menus.

7. Press “ENTER” button to perform a selected

function.

For TranScanner 2 the brand code is “080”.

- 9 of 18 -

THE FRONT PANEL CONTROLS

POWER

DWIN

MENU FUNCTION VALUE

ran 2

canner

VARIABLE LINE MULTIPLIER

a\`]

The front panel controls on the TranScanner 2 include a “MENU” button; "up \ and down ]" “FUNCTION” buttons;

left ` and right a“VALUE” buttons; a “POWER” button and an indicator light which is illuminated when the unit is

turned on.

The “MENU” button selects one of four screens with individual adjustments for video settings, input selection,

aspect ratio selection and set-up functions.

When one of the on-screen menus is selected, the up \ and down ]buttons may be used to select individual items

from the menu. The left ` and right abuttons are used to change these control settings.

There are 100 increments for the picture adjustments with "50" being the mid-point. Individual picture settings

can be stored for each one of the nine video inputs. Sharpness adjustment has increments from 0 to 3.

USING THE CONTROL MENUS

Main Menu

The Main menu offers a choice of video controls, input selection,

aspect ratio selection and set-up functions. Press the “MENU”

button to display the Main menu. Scroll up \or ] down the list to

highlight “Video”, then press the “MENU” button on the remote

or on the front panel of the TranScanner 2. A new menu will

appear on the screen. Press “MENU” again to return to the

main menu or press “EXIT” on the remote to clear the screen

immediately. Also the "Time Out" feature will automatically clear

the screen unless another button is pressed approximately ten

seconds after the menu appears on the screen.

Input

Set Up

Video Video 1

Aspect Ratio 4:3 Std

Video Control Menu

Press the “MENU” button to display the Main menu. Use the up \ or ]down buttons to highlight the “Video”

option. Press the “MENU” button again to advance to Video control menu.

Input

Set Up Brightness

Color

Tint

Sharpness

Video

Contrast

Video 1

Contrast 50

Aspect Ratio 4:3 Std

- 10 of 18 -

Use the left `or a right buttons to obtain desired video settings. Once you press the left ` or a right buttons this

menu will be replaced with a single line display at the bottom of the screen. This makes it easier to see the picture

to adjust the control settings. To restore the full menu, press up \ or ]down buttons or the “MENU” button.

Picture setting changes made with the Video menu are saved in non-volatile memory for each of the nine video

inputs. Many video sources are different enough to warrant this fine-tuning and these settings will be

automatically recalled each time video input is switched.

Input Menu

From the Main menu scroll up \ or down ]to highlight the Input

option. Use left `or right abuttons to sequence through input

sources. Input source selections can be made at any time (even

without an on screen menu) by pressing numbers 1 through 9 on

the remote control. The composite video inputs are 1 and 2, S-

Video inputs are 3 and 4, component video inputs are 5, 6 and 7,

the RGB inputs are 8 and 9.

Note: See IR Setup menu for further information.

Input

Video Video 1

Aspect Ratio 4:3 Std

Set Up

Aspect Ratio Menu

From the Main menu scroll up \ or down ]to highlight the Aspect

Ratio option. This enables you to select the aspect ratio in use,

regardless of the input device. Aspect ratio selections can be

made by pressing numbers 1 through 5 on the remote control.

Press “MENU” button again to advance to the Aspect Ratio

menu. Use up \ or down ] buttons to highlight the Aspect Ratio

option. Use left `or right abuttons to select the desired aspect

ratio.

Input

Video Video 1

Aspect Ratio 4:3 Std

Set Up

Set Up Menu

From the Main menu scroll up \ or down ]to highlight the Set Up

option and press the “MENU”button to display the Set Up menu.

No Yes

Menu Timeout √Short

Long

Rename Inputs b

Rename Aspect Ratios b

Display Setup b

IR Setup b

Relay Setup b

OSG Setup b

Auto Input Select

1. 4:3 Std

2. 1.85 A

3. 1.85 LB

4. 2.35 A

5. 2.35 LB

Autres manuels pour 2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dwin Matériel informatique

Dwin

Dwin TransVision 3 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur